Mira Vie User guide

Type
User guide

This manual is also suitable for

Mira Beat and Nectar Shower Fittings
These instructions must be left with the user
Installation and User Guide
Use your thumb or a
soft cloth to wipe any
limescale from the soft
nozzles
Unscrew the hose
from the showerhead
and the shower outlet.
Inspect the hose.
USER MAINTENANCE
Cleaning
Many household cleaners contain abrasives and chemical substances,
and should not be used for cleaning plated or plastic ttings. These
nishes should be cleaned with a mild washing up detergent or soap
solution, and then wiped dry using a soft cloth.
Inspecting the Hose
Important! The shower hose should be inspected periodically for
damage or internal collapse, internal collapse can restrict the ow
rate from the showerhead and may cause damage to the shower.
Remove the shower hose from the shower, inspect and replace the
hose if necessary.
De-scaling the Showerhead
Important! Keeping the showerhead clean and free from limescale
will ensure that your shower and showerhead continue to perform to
their maximum. A blocked showerhead can restrict the ow rate and
may cause damage to your shower.
SPECIFICATION - PRESSURES
Minimum maintained pressure: 0.1 bar (10 kPa) - Maximum
maintained pressure: 5.0 bar (500 kPa)
1230751-W2-A (L16A/B/C)
© Kohler Mira Limited, January 2014
What to do if something goes wrong
If your product does not work correctly refer to this manual for fault diagnosis
and check that it is installed and commissioned in accordance with our
instructions.
If this does not resolve the issue, contact us for help and advice.
Helpdesk Service - Our Customer Services Team is comprehensively
trained and can offer help and advice, spare parts and accessories.
Please provide your model name or number and date of purchase.
Showers Website (www.mirashowers.co.uk)
From our website you can download additional user guides, diagnose
faults, purchase our full range of accessories and popular spares
and refer to our FAQs.
Spares and Accessories - We hold the largest stocks of genuine
Mira spares and accessories. Contact us for a price or visit our
website to purchase items from our accessory range and popular
spares.
01 531 9337
Mira Customer Services
Dept, Cromwell
Road, Cheltenham,
Gloucestershire, GL52 5EP
To Contact Us
E-mail: Visit www.
mirashowers.co.uk/
contactus
To Contact Us: Eire Only
0844 571 5000
Fax: 01 242 282595
E-mail: CustomerServiceEire
@mirashowers.com
CUSTOMER SERVICE
Guarantee
Your product has the benet of our manufacturer’s guarantee which starts
from the date of purchase.
Within the guarantee period we will resolve defects in materials or
workmanship, free of charge, by repairing or replacing parts or product as
we may choose.
This guarantee is in addition to your statutory rights and is subject to
the following conditions:
The product must be installed and maintained in accordance with the
instructions given in this user guide.
Replacement under this guarantee does not extend the original expiry
date. The guarantee on any replacement parts or product ends at the
original expiry date.
The guarantee does not cover:
Non product faults (such as damage or performance issues arising
from incorrect installation, improper use, inappropriate cleaning, lack
of maintenance, build up of limescale, frost damage, corrosion, system
debris or blocked lters) or where no fault has been found with the product.
Compensation for loss of use of the product or consequential loss of
any kind.
Damage or defects caused if the product is repaired or modied by
persons not authorised by us or our appointed representative.
Mira is a registered trade mark of
Kohler Mira Limited.
The company reserves the right to alter
product specications without notice.
FM 14648
The Mira Shower Fittings have been designed for domestic use only,
Mira Showers guarantee the ttings against any defect in materials
or workmanship for a period of one year from the date of purchase.
For non-domestic installations, Mira Showers guarantee the ttings
against any defect in materials or workmanship for a period of one
year from the date of purchase.
For terms and conditions, refer to the back cover of this guide.
GUARANTEE
Mira Nectar
Mira Beat
GENERAL
1. Make sure that the shower ttings are installed by a competent
installer.
2. Installations must comply with Water Regulations (Bye-Laws,
Scotland), and any other Local Regulations and Building
Regulations in force at the time of installation.
3. The shower ttings should be positioned at a convenient height
for all the family. Position the ttings to spray across rather
than towards the opening of the cubicle and also away from
the shower control. Avoid layouts where the shower hose will
be sharply kinked. This may reduce the life of the hose.
4. A hose retaining ring is supplied to prevent the showerhead
from dropping below the spill over level of the bath or shower,
which could lead to contamination from back-siphonage.
The position of the shower and shower ttings must provide
a minimum gap of 25 mm between the showerhead and the
spill over level of any bath, shower tray or basin and 30 mm
between the showerhead and the spill over level of any toilet
or bidet.
5. Do not t any form of ow control in the outlet pipe work if the
shower ttings are installed in conjunction with a product that
requires the ttings to act as a vent (e.g. an electric shower).
6. Wall screws and wall plugs are supplied with this product.
Special consideration should be given to the fixing
arrangements when installing onto a dry lined, stud
partition, shower cubicle or laminated panel wall
structures. Installers may wish to obtain alternative
proprietary cavity fixings, or choose other options,
however, these methods of xing are beyond the scope
of this guide.
Zone of
Backow Risk
30 mm
Minimum
Toilet or Bidet
FC5
Hand Basin
FC3
Bath or Shower
Tray FC3
Electric
Shower
25 mm
Minimum
Hose retaining ring tted and shower ttings xed at a suitable height
preventing dirty water backow
25 mm Minimum
5
7
INSTALLATION
1. We recommend that the slide bar is installed with the ends
ush. Mark the wall xing positions and drill two holes to suit
the wall xings.
Caution! Do not drill into cables or pipes in the wall.
Note! For new installation optimum xing centres 630 mm.
Replacement installation xing centres 630 mm maximum.
2. Install the wall plugs and the mounting brackets and secure
with the wall screws.
Note! Check for vertical alignment before tightening. The
mounting brackets are slotted to aid this alignment. Then fully
tighten.
3. Install the clamp bracket, the hose retaining ring and the slide
bar supports to the slide bar.
4. Make sure that the wall screws are ush with the inside edge
of the mounting brackets.
Fit the slide bar supports over the mounting brackets, then
adjust the slide bar vertically ensuring an equal length of slide
bar protrudes from the top and bottom mounting bracket (or
ush with the end of the slide bar for new installations).
5. Remove the slide bar assembly carefully, preventing any further
movement between the slide bar and the slide bar supports.
6. Tighten the two slide bar clamping screws no more than half
a turn to secure the slide bar supports to the slide bar.
Caution! Overtightening these screws will cause damage.
7. Install the slide bar assembly onto the mounting brackets.
Tighten the 2 x M4 screws with the supplied 3 mm hexagonal
key.
Caution! Do not force assembly on to the mounting brackets,
re-align a slide bar support if required.
Hose and Showerhead Installation
1. Fit a hose seal into the conical nut and screw onto the outlet
of the shower.
Caution! Do not over tighten.
2. Feed the hose through the hose retaining ring.
3. Fit a hose seal into the conical nut and screw onto the
showerhead.
Caution! Do not over tighten.
4. Place the showerhead assembly into the clamp bracket
assembly.
For New Installations Centre Distance 630 mm
For Retrot Installations Centre Distance 630 mm Max.
Shower Hose (1.25 m)
1703.210 (Plastic)
Beat Clamp
Bracket
1703.202 (White)
1703.203 (Chrome)
Slide Bar Support (x2)
(includes screws)
1740.595 (White)
1740.596 (Chrome)
Hose Retaining Ring
1703.449 (White)
1703.199 (Chrome)
Slide Bar
1703.204
(660 mm)
M4 Screws 'A' (x2)
Cap (x2)
1703.196
Note! Ensure an equal length of slide bar top and bottom.
Slide Bar
Clamping
Screw
Note! Do not overtighten the screws
Mounting Pack
Components 'A'
1703.194
Slide Bar Support
Slide Bar
Tighten slide bar clamping
screw no more than 1/2 turn
*
*
Nectar Clamp Bracket
1703.275 (White)
1703.276 (Chrome)
Beat Showerhead
1703.351 (Single
Mode - Chrome)
1703.352 (Single
Mode - White)
1703.353 (Multi
Mode - Chrome)
1703.354 (Multi
Mode - White)
Nectar Showerhead
1703.380 (Single
Mode - Chrome)
1703.381 (Single
Mode - White)
1703.382 (Multi
Mode - Chrome)
1703.383 (Multi
Mode - White)
  • Page 1 1
  • Page 2 2

Mira Vie User guide

Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI