Hussmann IMPACT D5RRI Connecting

Brand
Hussmann
Model
IMPACT D5RRI
Type
Connecting

This manual is also suitable for

Hussmann IMPACT D5RRI is a heavy duty joining system designed to connect multiple D5RRI and D5RRIS merchandisers together to create a continuous refrigerated display. The system includes all the necessary hardware to join the merchandisers together, including gaskets, cap screws, lock washers, flat washers, threaded rods, and hex nuts. The system also includes silicone sealer to help ensure a tight seal between the merchandisers.

The Hussmann IMPACT D5RRI joining system is easy to install and can be completed in just a few steps. First, the front panels of the merchandisers are fastened together using cap screws, flat washers, and lock washers. Next, the merchandisers are drawn together at the rear using cap screws, flat washers, and lock washers. Finally, the canopies of the merchandisers are drawn together using a threaded rod, washers, and nuts.

Hussmann IMPACT D5RRI is a heavy duty joining system designed to connect multiple D5RRI and D5RRIS merchandisers together to create a continuous refrigerated display. The system includes all the necessary hardware to join the merchandisers together, including gaskets, cap screws, lock washers, flat washers, threaded rods, and hex nuts. The system also includes silicone sealer to help ensure a tight seal between the merchandisers.

The Hussmann IMPACT D5RRI joining system is easy to install and can be completed in just a few steps. First, the front panels of the merchandisers are fastened together using cap screws, flat washers, and lock washers. Next, the merchandisers are drawn together at the rear using cap screws, flat washers, and lock washers. Finally, the canopies of the merchandisers are drawn together using a threaded rod, washers, and nuts.

1
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0435047
January, 2003
D5RRI and D5RRIS
Rear Roll-in Dairy
Joining Instruction
Merchandisers
®
PARTS LIST
Item Quantity Description
D5RRI D5RRIS
1. 1 1 Gasket
1
/2 x
1
/2 x 60 (1524 mm)
2. 1 1 Gasket
1
/2 x 1
5
/8 x 120 (3048 mm)
3. 9 5 Cap Screw
5
/16 -18 x 1
1
/4
4. 9 5 Lock Washer
5
/16
5. 9 5 Flat Washer
5
/16
6. 1 1 Threaded Rod
1
/2 -16 x 12 (305 mm)
7. 2 2 Flat Washer
1
/2
8. 2 2 Hex Nut
1
/
2 -16
9. 1 1 Silicone Sealer
Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in
the right end of each merchandiser.
NOTES:
• Be sure merchandisers have been
leveled according to the installation
instructions.
• Be sure factory-installed nut
retainers and alignment pins are in
place.
• Install optional shelf kits after all
merchandisers have been joined.
1
Remove front air grille and
honeycomb from the right end
as shown in Figure 1.
Right Front
Air Grille
Right Front
Honeycomb
Figure 1. Remove Air Grille and Honeycomb
D5RRI
D5RRIS
2
Verify that nut retainers and
alignment pins are installed in
the right-hand end of the left
case in the locations shown in
Figure 2.
P/N 0435047
Merchandisers
®
2
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Alignment Pins
Alignment Pins
Figure 2. Verify Nut Retainer and Alignment Pin Installation
3
Apply Gasket – 1 along the
center of the lower assembly.
Apply Gasket – 2 to cover
foam-to-metal gap at rear and
across top as shown in Figure 3.
Lap gaskets at lower corners.
Check that there are no gaps
between gasket and case.
• Do not stretch gasket,
especially around corners.
• Do not butt gaskets; always lap
joints.
• Remove paper backing after
gasket is applied.
Joining Instruction for D5RRI and D5RRIS
Rear Roll-in Dairy Merchandisers
P/N 0435047
3
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Optional
Low Front
2
Standard
1
1
Note: Case To Be
Sealed And
Gasketed As Shown
2
1
1
/2 in. x
1
/2 x 60
1
/2 in. x 1
5
/8 x 120
1
2
Figure 3. Apply Gaskets
Optional
Low Front
Standard Front
D5RRI
D5RRIS
4
Move second merchandiser
against first, mating alignment
pins with corresponding holes.
5
Fasten fronts together using
Cap Screw – 3,
Flat Washers – 4, and
Lock Washers – 5 as shown in
Figure 4. Tighten only until front
panels touch. Do not tighten
fully.
6
Use Cap Screws – 3 with
Flat Washers – 4 and
Lock Washers – 5 to draw
merchandisers together at rear.
Start at the bottom, then middle,
then top; tighten until gaskets are
compressed.
P/N 0435047
Merchandisers
®
4
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
5
Alignment
Pins
Nut Retainer
9 Places for D5RRI and
5 Places for D5RRIS
3
4
Figure 4. Joining Ends
7
Draw canopies together using
Rod – 6 through top shoe, and
Washers – 7, and Nuts – 8
on each end of rod as illustrated
in Figure 5. Stop when canopies
touch.
8
Apply a bead of Silicone – 9
to the joined merchandisers as
shown in Figure 6. When dry,
replace honeycomb.
Joining Instruction for D5RRI and D5RRIS
Rear Roll-in Dairy Merchandisers
P/N 0435047
5
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
8
7
6
7
8
Silicone Gun
Silicone Gun
Apply Silicone Bead
Apply Silicone Bead
D5RRI
D5RRIS
9
9
Figure 5. Canopy Joining
Figure 6. Applying Silicone
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Hussmann IMPACT D5RRI Connecting

Brand
Hussmann
Model
IMPACT D5RRI
Type
Connecting
This manual is also suitable for

Hussmann IMPACT D5RRI is a heavy duty joining system designed to connect multiple D5RRI and D5RRIS merchandisers together to create a continuous refrigerated display. The system includes all the necessary hardware to join the merchandisers together, including gaskets, cap screws, lock washers, flat washers, threaded rods, and hex nuts. The system also includes silicone sealer to help ensure a tight seal between the merchandisers.

The Hussmann IMPACT D5RRI joining system is easy to install and can be completed in just a few steps. First, the front panels of the merchandisers are fastened together using cap screws, flat washers, and lock washers. Next, the merchandisers are drawn together at the rear using cap screws, flat washers, and lock washers. Finally, the canopies of the merchandisers are drawn together using a threaded rod, washers, and nuts.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents