NXP P80C51SBAA User guide

Brand: NXP

Model: P80C51SBAA

Category: Power generators

Type: User guide

This manual is also suitable for

UM10334

P89LPC9301/931A1 User manual

Rev. 2 — 5 November 2010 User manual

Document information

Info Content

Keywords P89LPC9301/931A1

Abstract Technical information for the P89LPC9301/931A1 device

User manual Rev. 2 — 5 November 2010 2 of 119

Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

Revision history

Rev Date Description

v.2 20101105

• Section 2.3: added low speed oscillator information.

• Section 14.1: added low speed oscillator information.

• Section 14.3: added low speed oscillator information.

• Section 14.5: added low speed oscillator information.

• Table 8: added low speed oscillator information.

v.1 20090409 Initial version

User manual Rev. 2 — 5 November 2010 3 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

1. Introduction

The P89LPC9301/931A1 are single-chip microcontrollers designed for applications

demanding high-integration, low cost solutions over a wide range of performance

requirements. The P89LPC9301/931A1 are based on a high performance processor

architecture that executes instructions in two to four clocks, six times the rate of standard

80C51 devices. Many system-level functions have been incorporated into the

P89LPC9301/931A1 in order to reduce component count, board space, and system cost.

1.1 Pin configuration

1.2 Pin description

Fig 1. TSSOP28 pin configuration

P89LPC9301FDH

P89LPC931A1FDH

002aae451

P2.0

P2.1

P0.0/CMP2/KBI0

P1.7

P1.6

P1.5/RST

P3.1/XTAL1

P3.0/XTAL2/CLKOUT

P1.4/INT1

P1.3/INT0/SDA

P1.2/T0/SCL

P2.2/MOSI

P2.3/MISO

P2.7

P2.6

P0.1/CIN2B/KBI1

P0.2/CIN2A/KBI2

P0.3/CIN1B/KBI3

P0.4/CIN1A/KBI4

P0.5/CMPREF/KBI5

P0.6/CMP1/KBI6

P0.7/T1/KBI7

P1.0/TXD

P1.1/RXD

P2.5/SPICLK

P2.4/SS

Table 1. Pin description

Symbol Pin Type Description

TSSOP28

P0.0 to P0.7 I/O Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. During reset

Port 0 latches are configured in the input only mode with the internal pull-up

disabled. The operation of Port 0 pins as inputs and outputs depends upon the

port configuration selected. Each port pin is configured independently. Refer to

Section 4.1 “

Port configurations” for details.

The Keypad Interrupt feature operates with Port 0 pins.

All pins have Schmitt trigger inputs.

Port 0 also provides various special functions as described below:

P0.0/CMP2/

KBI0

3I/OP0.0 — Port 0 bit 0.

O CMP2 — Comparator 2 output

I KBI0 — Keyboard input 0.

P0.1/CIN2B/

KBI1

26 I/O P0.1 — Port 0 bit 1.

I CIN2B — Comparator 2 positive input B.

I KBI1 — Keyboard input 1.

User manual Rev. 2 — 5 November 2010 4 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

P0.2/CIN2A/

KBI2

25 I/O P0.2 — Port 0 bit 2.

I CIN2A — Comparator 2 positive input A.

I KBI2 — Keyboard input 2.

P0.3/CIN1B/

KBI3

24 I/O P0.3 — Port 0 bit 3. High current source.

I CIN1B — Comparator 1 positive input B.

I KBI3 — Keyboard input 3.

P0.4/CIN1A/

KBI4

23 I/O P0.4 — Port 0 bit 4. High current source.

I CIN1A — Comparator 1 positive input A.

I KBI4 — Keyboard input 4.

P0.5/CMPREF/

KBI5

22 I/O P0.5 — Port 0 bit 5. High current source.

I CMPREF — Comparator reference (negative) input.

I KBI5 — Keyboard input 5.

P0.6/CMP1/KBI6 20 I/O P0.6 — Port 0 bit 6. High current source.

O CMP1 — Comparator 1 output.

I KBI6 — Keyboard input 6.

P0.7/T1/KBI7 19 I/O P0.7 — Port 0 bit 7. High current source.

I/O T1 — Timer/counter 1 external count input or overflow output.

I KBI7 — Keyboard input 7.

P1.0 to P1.7 I/O, I

[1]

Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for

three pins as noted below. During reset Port 1 latches are configured in the input

only mode with the internal pull-up disabled. The operation of the configurable

Port 1 pins as inputs and outputs depends upon the port configuration selected.

Each of the configurable port pins are programmed independently. Refer to

Section 4.1 “

Port configurations” for details. P1.2 to P1.3 are open drain when

used as outputs. P1.5 is input only.

All pins have Schmitt trigger inputs.

Port 1 also provides various special functions as described below:

P1.0/TXD 18 I/O P1.0 — Port 1 bit 0.

O TXD — Transmitter output for serial port.

P1.1/RXD 17 I/O P1.1 — Port 1 bit 1.

I RXD — Receiver input for serial port.

P1.2/T0/SCL 12 I/O P1.2 — Port 1 bit 2 (open-drain when used as output).

I/O T0 — Timer/counter 0 external count input or overflow output (open-drain when

used as output).

I/O SCL — I

C-bus serial clock input/output.

P1.3/INT0

/SDA 11 I/O P1.3 — Port 1 bit 3 (open-drain when used as output).

I INT0

— External interrupt 0 input.

I/O SDA — I

C-bus serial data input/output.

P1.4/INT1

10 I/O P1.4 — Port 1 bit 4. High current source.

I INT1

— External interrupt 1 input.

Table 1. Pin description

…continued

Symbol Pin Type Description

TSSOP28

User manual Rev. 2 — 5 November 2010 5 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

P1.5/RST 6IP1.5 — Port 1 bit 5 (input only).

I RST

— External Reset input during power-on or if selected via UCFG1. When

functioning as a reset input, a LOW on this pin resets the microcontroller, causing

I/O ports and peripherals to take on their default states, and the processor begins

execution at address 0. Also used during a power-on sequence to force ISP mode.

P1.6 5 I/O P1.6 — Port 1 bit 6. High current source.

P1.7 4 I/O P1.7 — Port 1 bit 7. High current source.

P2.0 to P2.7 I/O Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type. During reset

Port 2 latches are configured in the input only mode with the internal pull-up

disabled. The operation of Port 2 pins as inputs and outputs depends upon the

port configuration selected. Each port pin is configured independently. Refer to

Section 4.1 “

Port configurations” for details.

All pins have Schmitt trigger inputs.

Port 2 also provides various special functions as described below:

P2.0 1 I/O P2.0 — Port 2 bit 0.

P2.1 2 I/O P2.1 — Port 2 bit 1.

P2.2/MOSI 13 I/O P2.2 — Port 2 bit 2.

I/O MOSI — SPI master out slave in. When configured as master, this pin is output;

when configured as slave, this pin is input.

P2.3/MISO 14 I/O P2.3 — Port 2 bit 3.

I/O MISO — When configured as master, this pin is input, when configured as slave,

this pin is output.

P2.4/SS

15 I/O P2.4 — Port 2 bit 4.

I SS

— SPI Slave select.

P2.5/SPICLK 16 I/O P2.5 — Port 2 bit 5.

I/O SPICLK — SPI clock. When configured as master, this pin is output; when

configured as slave, this pin is input.

P2.6 27 I/O P2.6 — Port 2 bit 6.

P2.7 28 I/O P2.7 — Port 2 bit 7.

P3.0 to P3.1 I/O Port 3: Port 3 is a 2-bit I/O port with a user-configurable output type. During reset

Port 3 latches are configured in the input only mode with the internal pull-up

disabled. The operation of Port 3 pins as inputs and outputs depends upon the

port configuration selected. Each port pin is configured independently. Refer to

Section 4.1 “

Port configurations” for details.

All pins have Schmitt trigger inputs.

Port 3 also provides various special functions as described below:

P3.0/XTAL2/

CLKOUT

9I/OP3.0 — Port 3 bit 0.

O XTAL2 — Output from the oscillator amplifier (when a crystal oscillator option is

selected via the flash configuration.

O CLKOUT — CPU clock divided by 2 when enabled via SFR bit (ENCLK -TRIM.6).

It can be used if the CPU clock is the internal RC oscillator, watchdog oscillator or

external clock input, except when XTAL1/XTAL2 are used to generate clock

source for the RTC/system timer.

Table 1. Pin description

…continued

Symbol Pin Type Description

TSSOP28

User manual Rev. 2 — 5 November 2010 6 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

[1] Input/output for P1.0 to P1.4, P1.6, P1.7. Input for P1.5.

P3.1/XTAL1 8 I/O P3.1 — Port 3 bit 1.

I XTAL1 — Input to the oscillator circuit and internal clock generator circuits (when

selected via the flash configuration). It can be a port pin if internal RC oscillator or

watchdog oscillator is used as the CPU clock source, and if XTAL1/XTAL2 are not

used to generate the clock for the RTC/system timer.

7IGround: 0 V reference.

21 I Power supply: This is the power supply voltage for normal operation as well as

Idle and Power-down modes.

Table 1. Pin description

…continued

Symbol Pin Type Description

TSSOP28

User manual Rev. 2 — 5 November 2010 7 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

1.3 Logic symbols

Fig 2. P89LPC9301/931A1 logic symbol

PORT 0

PORT 3

TXD

RXD

INT0

INT1

RST

SCL

SDA

002aae448

CMP2

CIN2B

CIN2A

CIN1B

CIN1A

CMPREF

CMP1

XTAL2

XTAL1

KBI0

KBI1

KBI2

KBI3

KBI4

KBI5

KBI6

KBI7

MOSI

MISO

SPICLK

PORT 1

PORT 2

P89LPC9301/

931A1

CLKOUT

User manual Rev. 2 — 5 November 2010 8 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

1.4 Block diagram

Fig 3. Block diagram

HIGH PERFORMANCE

ACCELERATED 2-CLOCK 80C51 CPU

4 kB/8 kB

CODE FLASH

256-BYTE

DATA RAM

PORT 2

CONFIGURABLE I/Os

PORT 0

CONFIGURABLE I/Os

KEYPAD

INTERRUPT

PROGRAMMABLE

OSCILLATOR DIVIDER

CPU

clock

CONFIGURABLE

OSCILLATOR

ON-CHIP RC

OSCILLATOR WITH

CLOCK DOUBLER

internal

bus

CRYSTAL

RESONATOR

POWER MONITOR

(POWER-ON RESET,

BROWNOUT RESET)

002aae447

ANALOG

COMPARATORS

C-BUS

PORT 3

CONFIGURABLE I/Os

P89LPC9301/931A1

TIMER 0

TIMER 1

WATCHDOG TIMER

AND OSCILLATOR

P3[1:0]

P2[7:0]

PORT 1

CONFIGURABLE I/Os

P1[7:0]

P0[7:0]

XTAL2

XTAL1

SCL

SDA

TXD

RXD

UART

REAL-TIME CLOCK/

SYSTEM TIMER

CMP2

CIN2B

CIN2A

CMP1

CIN1A

CIN1B

SPI

SPICLK

MOSI

MISO

User manual Rev. 2 — 5 November 2010 9 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

1.5 Special function registers

Remark: SFR accesses are restricted in the following ways:

• User must not attempt to access any SFR locations not defined.

• Accesses to any defined SFR locations must be strictly for the functions for the SFRs.

• SFR bits labeled ‘-’, ‘0’ or ‘1’ can only be written and read as follows:

– ‘-’ Unless otherwise specified, must be written with ‘0’, but can return any value

when read (even if it was written with ‘0’). It is a reserved bit and may be used in

future derivatives.

– ‘0’ must be written with ‘0’, and will return a ‘0’ when read.

– ‘1’ must be written with ‘1’, and will return a ‘1’ when read.

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 10 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

Table 2. Special function registers

* indicates SFRs that are bit addressable.

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

Bit addressE7E6E5E4E3E2E1E0

ACC* Accumulator E0H 00 0000 0000

AUXR1 Auxiliary

function

A2H CLKLP EBRR ENT1 ENT0 SRST 0 - DPS 00 0000 00x0

Bit addressF7F6F5F4F3F2F1F0

B* B register F0H 00 0000 0000

BRGR0

[2]

Baud rate

generator 0

rate low

BEH 00 0000 0000

BRGR1

[2]

Baud rate

generator 0

rate high

BFH 00 0000 0000

BRGCON Baud rate

generator 0

control

BDH------SBRGSBRGEN00

[2]

xxxx xx00

CMP1 Comparator 1

control register

ACH - - CE1 CP1 CN1 OE1 CO1 CMF1 00

[1]

xx00 0000

CMP2 Comparator 2

control register

ADH - - CE2 CP2 CN2 OE2 CO2 CMF2 00

[1]

xx00 0000

DIVM CPU clock

divide-by-M

control

95H 00 0000 0000

DPTR Data pointer

(2 bytes)

DPH Data pointer

high

83H 00 0000 0000

DPL Data pointer

low

82H 00 0000 0000

FMADRH Program flash

address high

E7H 00 0000 0000

FMADRL Program flash

address low

E6H 00 0000 0000

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 11 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

FMCON Program flash

control (Read)

E4H BUSY - - - HVA HVE SV OI 70 0111 0000

Program flash

control (Write)

E4H FMCMD.7 FMCMD.6 FMCMD.5 FMCMD.4 FMCMD.3 FMCMD.2 FMCMD.1 FMCMD.0

FMDATA Program flash

data

E5H 00 0000 0000

I2ADR I

C-bus slave

address

DBH I2ADR.6 I2ADR.5 I2ADR.4 I2ADR.3 I2ADR.2 I2ADR.1 I2ADR.0 GC 00 0000 0000

Bit address DF DE DD DC DB DA D9 D8

I2CON* I

C-bus control

D8H - I2EN STA STO SI AA - CRSEL 00 x000 00x0

I2DAT I

C-bus data

DAH

I2SCLH Serial clock

generator/SCL

duty cycle

DDH 00 0000 0000

I2SCLL Serial clock

generator/SCL

duty cycle

DCH 00 0000 0000

I2STAT I

C-bus status

D9H STA.4 STA.3 STA.2 STA.1 STA.0 0 0 0 F8 11111000

Bit address AF AE AD AC AB AA A9 A8

IEN0* Interrupt

enable 0

A8H EA EWDRT EBO ES/ESR ET1 EX1 ET0 EX0 00 0000 0000

Bit address EF EE ED EC EB EA E9 E8

IEN1* Interrupt

enable 1

E8H - EST - - ESPI EC EKBI EI2C 00

[1]

00x0 0000

Table 2. Special function registers …continued

* indicates SFRs that are bit addressable.

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 12 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

Bit address BF BE BD BC BB BA B9 B8

IP0* Interrupt

priority 0

B8H - PWDRT PBO PS/PSR PT1 PX1 PT0 PX0 00

[1]

x000 0000

IP0H Interrupt

priority 0 high

B7H - PWDRTH PBOH PSH/

PSRH

PT1H PX1H PT0H PX0H 00

[1]

x000 0000

Bit address FF FE FD FC FB FA F9 F8

IP1* Interrupt

priority 1

F8H - PST - - PSPI PC PKBI PI2C 00

[1]

00x0 0000

IP1H Interrupt

priority 1 high

F7H - PSTH - - PSPIH PCH PKBIH PI2CH 00

[1]

00x0 0000

KBCON Keypad control

94H------PATN

_SEL

KBIF 00

[1]

xxxx xx00

KBMASK Keypad

interrupt mask

86H 00 0000 0000

KBPATN Keypad pattern

93H FF 1111 1111

Bit address8786858483828180

P0* Port 0 80H T1/KB7 CMP1

/KB6

CMPREF

/KB5

CIN1A

/KB4

CIN1B

/KB3

CIN2A

/KB2

CIN2B

/KB1

CMP2

/KB0

[1]

Bit address9796959493929190

P1* Port 1 90H - - RST

INT1 INT0/SDA T0/SCL RXD TXD

[1]

Bit addressA7A6A5A4A3A2A1A0

P2* Port 2 A0H - - SPICLK SS

MISO MOSI - -

[1]

Bit addressB7B6B5B4B3B2B1B0

P3*Port3B0H------XTAL1XTAL2

[1]

P0M1 Port 0 output

mode 1

84H (P0M1.7) (P0M1.6) (P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF

[1]

1111 1111

P0M2 Port 0 output

mode 2

85H (P0M2.7) (P0M2.6) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) 00

[1]

0000 0000

P1M1 Port 1 output

mode 1

91H (P1M1.7) (P1M1.6) - (P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) D3

[1]

11x1 xx11

Table 2. Special function registers

…continued

* indicates SFRs that are bit addressable.

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 13 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

P1M2 Port 1 output

mode 2

92H (P1M2.7) (P1M2.6) - (P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) 00

[1]

00x0 xx00

P2M1 Port 2 output

mode 1

A4H (P2M1.7) (P2M1.6) (P2M1.5) (P2M1.4) (P2M1.3) (P2M1.2) (P2M1.1) (P2M1.0) FF

[1]

1111 1111

P2M2 Port 2 output

mode 2

A5H (P2M2.7) (P2M2.6) (P2M2.5) (P2M2.4) (P2M2.3) (P2M2.2) (P2M2.1) (P2M2.0) 00

[1]

0000 0000

P3M1 Port 3 output

mode 1

B1H------(P3M1.1)(P3M1.0)03

[1]

xxxx xx11

P3M2 Port 3 output

mode 2

B2H------(P3M2.1)(P3M2.0)00

[1]

xxxx xx00

PCON Power control

87H SMOD1 SMOD0 - BOI GF1 GF0 PMOD1 PMOD0 00 0000 0000

PCONA Power control

B5H RTCPD - VCPD - I2PD SPPD SPD - 00

[1]

0000 0000

Bit addressD7D6D5D4D3D2D1D0

PSW* Program status

word

D0H CY AC F0 RS1 RS0 OV F1 P 00 0000 0000

PT0AD Port 0 digital

input disable

F6H - - PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1 - 00 xx00 000x

RSTSRC Reset source

DFH - BOIF BOF POF R_BK R_WD R_SF R_EX

[3]

RTCCON RTC control D1H RTCF RTCS1 RTCS0 - - - ERTC RTCEN 60

[1][6]

011x xx00

RTCH RTC register

high

D2H 00

[6]

0000 0000

RTCL RTC register

low

D3H 00

[6]

0000 0000

SADDR Serial port

address

A9H 00 0000 0000

SADEN Serial port

address enable

B9H 00 0000 0000

SBUF Serial Port data

buffer register

99H xx xxxx xxxx

Table 2. Special function registers

…continued

* indicates SFRs that are bit addressable.

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 14 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

Bit address 9F 9E 9D 9C 9B 9A 99 98

SCON* Serial port

control

98H SM0/FE SM1 SM2 REN TB8 RB8 TI RI 00 0000 0000

SSTAT Serial port

extended

status register

BAH DBMOD INTLO CIDIS DBISEL FE BR OE STINT 00 0000 0000

SP Stack pointer 81H 07 0000 0111

SPCTL SPI control

E2H SSIG SPEN DORD MSTR CPOL CPHA SPR1 SPR0 04 0000 0100

SPSTAT SPI status

E1HSPIFWCOL------0000xxxxxx

SPDAT SPI data

E3H 00 0000 0000

TAMOD Timer 0 and 1

auxiliary mode

8FH - - - T1M2 - - - T0M2 00 xxx0 xxx0

Bit address 8F 8E 8D 8C 8B 8A 89 88

TCON* Timer 0 and 1

control

88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00 0000 0000

TH0 Timer 0 high 8CH 00 0000 0000

TH1 Timer 1 high 8DH 00 0000 0000

TL0 Timer 0 low 8AH 00 0000 0000

TL1 Timer 1 low 8BH 00 0000 0000

TMOD Timer 0 and 1

mode

89H T1GATE T1C/T T1M1 T1M0 T0GATE T0C/T T0M1 T0M0 00 0000 0000

TRIM Internal

oscillator trim

96H RCCLK ENCLK TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0

[5][6]

WDCON Watchdog

control register

A7H PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK

[4][6]

Table 2. Special function registers …continued

* indicates SFRs that are bit addressable.

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 15 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

[1] All ports are in input only (high-impedance) state after power-up.

[2] BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable.

[3] The RSTSRC register reflects the cause of the P89LPC9301/931A1 reset except BOIF bit. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the

power-on reset value is x011 0000.

[4] After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset.

Other resets will not affect WDTOF.

[5] On power-on reset and watchdog reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.

[6] The only reset sources that affect these SFRs are power-on reset and watchdog reset.

WDL Watchdog load C1H FF 1111 1111

WFEED1 Watchdog

feed 1

C2H

WFEED2 Watchdog

feed 2

C3H

Table 2. Special function registers …continued

* indicates SFRs that are bit addressable.

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

User manual Rev. 2 — 5 November 2010 16 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

[1] Extended SFRs are physically located on-chip but logically located in external data memory address space (XDATA). The MOVX A,@DPTR and MOVX @DPTR,A instructions are

used to access these extended SFRs.

[2] The BOICFG1/0 will be copied from UCFG1.5 and UCFG1.3 when power-on reset.

[3] CLKCON register reset value comes from UCFG1 and UCFG2. The reset value of CLKCON.2 to CLKCON.0 come from UCFG1.2 to UCFG1.0 and reset value of CLKDBL bit

comes from UCFG2.7.

Table 3. Extended special function registers

[1]

Name Description SFR

addr.

Bit functions and addresses Reset value

MSB LSB Hex Binary

BODCFG BOD

configuration

FFC8H - - - - - - BOICFG1 BOICFG0

[2]

CLKCON CLOCK Control

FFDEH CLKOK - - XTALWD CLKDBL FOSC2 FOSC1 FOSC0

[3]

RTCDATH Real-time clock

data register

high

FFBFH 00 0000 0000

RTCDATL Real-time clock

data register low

FFBEH 00 0000 0000

User manual Rev. 2 — 5 November 2010 17 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

1.6 Memory organization

The various P89LPC9301/931A1 memory spaces are as follows:

DATA — 128 bytes of internal data memory space (00h:7Fh) accessed via direct or

indirect addressing, using instruction other than MOVX and MOVC. All or part of the Stack

may be in this area.

IDATA — Indirect Data. 256 bytes of internal data memory space (00h:FFh) accessed via

indirect addressing using instructions other than MOVX and MOVC. All or part of the

Stack may be in this area. This area includes the DATA area and the 128 bytes

immediately above it.

SFR — Special Function Registers. Selected CPU registers and peripheral control and

status registers, accessible only via direct addressing.

CODE — 64 kB of Code memory space, accessed as part of program execution and via

the MOVC instruction. The P89LPC9301/931A1 has 8 kB of on-chip Code memory.

(1) ISP code is located at the end of sector 3 on the P89LPC9301 and at the end of sector 7 on the P89LPC931A1.

Fig 4. P89LPC9301/931A1 memory map

002aae484

0000h

03FFh

0400h

07FFh

0800h

0BFFh

0C00h

0FFFh

SECTOR 0

SECTOR 1

SECTOR 2

SECTOR 3

1000h

13FFh

1400h

17FFh

1800h

1BFFh

1C00h

1E00h

1FFFh

SECTOR 4

SECTOR 5

SECTOR 6

FFEFh

FF00h

IAP entry-

points

SECTOR 7

ISP CODE

(512B)

(1)

SPECIAL FUNCTION

REGISTERS

(DIRECTLY ADDRESSABLE)

128 BYTES ON-CHIP

DATA MEMORY (STACK,

DIRECT AND INDIR. ADDR.)

4 REG. BANKS R[7:0]

data memory

(DATA, IDATA)

DATA

128 BYTES ON-CHIP

DATA MEMORY (STACK

AND INDIR. ADDR.)

IDATA (incl. DATA)

FFEFh FFh

80h

7Fh

00h

FF1Fh

FF00h

entry points for:

-51 ASM. code

-C code

IDATA routines

1FFFh

1E00h

entry points for:

-UART (auto-baud)

-I2C, SPI, etc.

(1)

ISP serial loader

entry

points

read-protected

IAP calls only

EXTENDED SFRs

FFFFh

FFB0h

RESERVED

XDATA

0000h

Table 4. Data RAM arrangement

Type Data RAM Size (bytes)

DATA Directly and indirectly addressable memory 128

IDATA Indirectly addressable memory 256

User manual Rev. 2 — 5 November 2010 18 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

2. Clocks

2.1 Enhanced CPU

The P89LPC9301/931A1 uses an enhanced 80C51 CPU which runs at six times the

speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and

most instructions execute in one or two machine cycles.

2.2 Clock definitions

The P89LPC9301/931A1 device has several internal clocks as defined below:

OSCCLK — Input to the DIVM clock divider. OSCCLK is selected from one of four clock

sources and can also be optionally divided to a slower frequency (see Figure 6

and

Section 2.10 “

CPU Clock (CCLK) modification: DIVM register”). Note: f

osc

is defined as

the OSCCLK frequency.

CCLK — CPU clock; output of the DIVM clock divider. There are two CCLK cycles per

machine cycle, and most instructions are executed in one to two machine cycles (two or

four CCLK cycles).

RCCLK — The internal 7.373 MHz RC oscillator output.The clock doubler option, when

enabled, provides an output frequency of 14.746 MHz.

PCLK — Clock for the various peripheral devices and is

CCLK

⁄

2.2.1 Oscillator Clock (OSCCLK)

The P89LPC9301/931A1 provides several user-selectable oscillator options in generating

the CPU clock. This allows optimization for a range of needs from high precision to lowest

possible cost. These options are configured when the flash is programmed and include an

on-chip watchdog oscillator, an on-chip RC oscillator, an oscillator using an external

crystal, or an external clock source.

2.3 Crystal oscillator option

The crystal oscillator can be optimized for low, medium, or high frequency crystals

covering a range from 20 kHz to 18 MHz. It can be the clock source of OSCCLK and RTC.

Low speed oscillator option can be the clock source of WDT.

2.3.1 Low speed oscillator option

This option supports an external crystal in the range of 20 kHz to 100 kHz. Ceramic

resonators are also supported in this configuration

2.3.2 Medium speed oscillator option

This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic

resonators are also supported in this configuration.

2.3.3 High speed oscillator option

This option supports an external crystal in the range of 4 MHz to 18 MHz. Ceramic

resonators are also supported in this configuration.

User manual Rev. 2 — 5 November 2010 19 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

2.4 Clock output

The P89LPC9301/931A1 supports a user-selectable clock output function on the XTAL2 /

CLKOUT pin when the crystal oscillator is not being used. This condition occurs if a

different clock source has been selected (on-chip RC oscillator, watchdog oscillator,

external clock input on X1) and if the Real-time Clock and Watchdog Timer are not using

the crystal oscillator as their clock source. This allows external devices to synchronize to

the P89LPC9301/931A1. This output is enabled by the ENCLK bit in the TRIM register.

The frequency of this clock output is

⁄

that of the CCLK. If the clock output is not needed

in Idle mode, it may be turned off prior to entering Idle, saving additional power. Note: on

reset, the TRIM SFR is initialized with a factory preprogrammed value. Therefore when

setting or clearing the ENCLK bit, the user should retain the contents of other bits of the

TRIM register. This can be done by reading the contents of the TRIM register (into the

ACC for example), modifying bit 6, and writing this result back into the TRIM register.

Alternatively, the ‘ANL direct’ or ‘ORL direct’ instructions can be used to clear or set bit 6

of the TRIM register.

2.5 On-chip RC oscillator option

The P89LPC9301/931A1 has a 6-bit TRIM register that can be used to tune the frequency

of the RC oscillator. During reset, the TRIM value is initialized to a factory

pre-programmed value to adjust the oscillator frequency to 7.373 MHz ± 1 % at room

temperature. (Note: the initial value is better than 1 %; please refer to the

P89LPC9301/931A1 data sheet for behavior over temperature). End user applications

can write to the TRIM register to adjust the on-chip RC oscillator to other frequencies.

Increasing the TRIM value will decrease the oscillator frequency. When the clock doubler

option is enabled (UCFG2.7 = 1), the output frequency is doubled. If CCLK is 8 MHz or

slower, the CLKLP SFR bit (AUXR1.7) can be set to logic 1 to reduce power consumption.

On reset, CLKLP is logic 0 allowing highest performance access. This bit can then be set

in software if CCLK is running at 8 MHz or slower. When clock doubler option is enabled,

BOE1 bit (UCFG1.5) and BOE0 bit (UCFG1.3) are required to hold the device in reset at

power-up until V

has reached its specified level.

Table 5. On-chip RC oscillator trim register (TRIM - address 96h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol RCCLK ENCLK TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0

Reset 0 0 Bits 5:0 loaded with factory stored value during reset.

User manual Rev. 2 — 5 November 2010 20 of 119

NXP Semiconductors

UM10334

P89LPC9301/931A1 User manual

2.6 Watchdog oscillator option

The watchdog has a separate oscillator which has a frequency of 400 kHz, calibrated to

± 5 % at room temperature. This oscillator can be used to save power when a high clock

frequency is not needed.

2.7 External clock input option

In this configuration, the processor clock is derived from an external source driving the

XTAL1 / P3.1 pin. The rate may be from 0 Hz up to 18 MHz. The XTAL2 / P3.0 pin may be

used as a standard port pin or a clock output. When using an oscillator frequency above

12 Mhz, BOE1 bit (UCFG1.5) and BOE0 bit (UCFG1.3) are required to hold the device in

reset at power-up until V

has reached its specified level.

Table 6. On-chip RC oscillator trim register (TRIM - address 96h) bit description

Bit Symbol Description

0 TRIM.0 Trim value. Determines the frequency of the internal RC oscillator. During reset,

these bits are loaded with a stored factory calibration value. When writing to either

bit 6 or bit 7 of this register, care should be taken to preserve the current TRIM value

by reading this register, modifying bits 6 or 7 as required, and writing the result to

this register.

1TRIM.1

2TRIM.2

3TRIM.3

4TRIM.4

5TRIM.5

6 ENCLK when = 1,

CCLK

⁄

is output on the XTAL2 pin provided the crystal oscillator is not

being used.

7 RCCLK when = 1, selects the RC Oscillator output as the CPU clock (CCLK). This allows for

fast switching between any clock source and the internal RC oscillator without

needing to go through a reset cycle.

Note: The oscillator must be configured in one of the following modes: Low frequency crystal,

medium frequency crystal, or high frequency crystal.

(1) A series resistor may be required to limit crystal drive levels. This is especially important for low

frequency crystals (see text).

Fig 5. Using the crystal oscillator

002aad364

XTAL1

XTAL2

quartz crystal or

ceramic resonator

(1)

Page is loading ...

NXP P80C51SBAA User guide

Brand: NXP

Model: P80C51SBAA

Category: Power generators

Type: User guide

This manual is also suitable for

Download PDF

report

NXP P80C51SBAA User guide

This manual is also suitable for

NXP P80C51SBAA User guide

Related papers

Other documents