Planet ADN-4100 Owner's manual

802.11n Wireless ADSL 2/2+ Router

ADN-4100

User's Manual

Copyright

this publication may be reproduced, transmitted, transcribed, stored in a retrieval

system, or translated into any language or computer language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with

respect to the contents hereof and specifically disclaims any warranties,

merchantability or fitness for any particular purpose. Any software described in

this manual is sold or licensed "as is". Should the programs prove defective

following their purchase, the buyer (and not this company, its distributor, or its

dealer) assumes the entire cost of all necessary servicing, repair, and any incidental

or consequential damages resulting from any defect in the software. Further, this

company reserves the right to revise this publication and to make changes from

time to time in the contents hereof without obligation to notify any person of such

revision or changes.

All brand and product names mentioned in this manual are trademarks and/or

registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

ii

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance (example-use only shielded interface cables when

connecting to computer or peripheral devices). Any changes or modifications not

expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

Following two conditions: (1) This device may not cause harmful interference, and

(2) this Device must accept any interference received, including interference that

may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled

environment. In order to avoid the possibility of exceeding the FCC radio frequency

exposure limits, human proximity to the antenna shall not be less than 20 cm (8

inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF

THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio

equipment and telecommunication terminal Equipment and the mutual recognition

of their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)

As of April 8, 2000.

WEEE Regulation

To avoid the potential effects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic

equipment, end users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of

WEEE as unsorted municipal waste and have to collect such WEEE separately.

Safety

This equipment is designed with the utmost care for the safety of those who install

and use it. However, special attention must be paid to the dangers of electric shock

and static electricity when working with electrical equipment. All guidelines of this

and of the computer manufacture must therefore be allowed at all times to ensure

the safe use of the equipment.

Energy Saving Note of the Device

This power required device does not support Standby mode operation.

For energy saving, please remove the power cable or push the power button to

OFF position to disconnect the device from the power circuit.

Without removing power cable or Power off, the device will still consuming power

from the power source. In the view of Saving the Energy and reduce the

unnecessary power consuming, it is strongly suggested to remove the power

connection for the device if this device is not intended to be active.

Revision

User’s Manual for 802.11n Wireless ADSL 2/2+ Router

Model: ADN-4100

Rev: 1.0 (Sep. 2010)

Part No. EM-ADN4100_v1

iii

i

Contents

1 Overview………….............................................................................................. 1

1.1 Safety Precautions ................................................................................ 1

1.2 LEDs and Interfaces .............................................................................. 2

1.3 System Requirements ........................................................................... 4

1.4 Features ................................................................................................ 4

2 Hardware Installation ......................................................................................... 6

3 Web Configuration .............................................................................................8

3.1 Accessing the Device ............................................................................ 8

3.2 General Configuration ........................................................................... 9

3.2.1 Wizard....................................................................................... 10

3.2.2 Internet Setup ........................................................................... 16

3.2.3 Wireless Setup.......................................................................... 19

3.2.4 Local Network ........................................................................... 27

3.2.5 Time and Date .......................................................................... 31

3.2.6 Logout....................................................................................... 32

3.3 Advanced Configuration ...................................................................... 32

3.3.1 Advanced Wireless................................................................... 32

3.3.2 Port Forwarding ........................................................................ 40

3.3.3 DMZ .......................................................................................... 42

3.3.4 Parental Control........................................................................ 43

3.3.5 Filtering Options........................................................................ 47

3.3.6 QoS Config ............................................................................... 52

3.3.7 Firewall Settings ....................................................................... 56

3.3.8 DNS .......................................................................................... 57

3.3.9 Dynamic DNS ........................................................................... 58

3.3.10 Network Tools...................................................................... 60

3.3.11 Routing ................................................................................ 75

3.3.12 Schedules............................................................................ 79

3.3.13 Logout ................................................................................. 80

3.4 Management........................................................................................ 80

3.4.1 System...................................................................................... 80

3.4.2 Firmware Update ...................................................................... 82

3.4.3 Access Controls........................................................................ 83

3.4.4 Diagnostics ............................................................................... 87

ii

3.4.5 Log Configuration ..................................................................... 87

3.4.6 Logout....................................................................................... 88

3.5 Status................................................................................................... 89

3.5.1 Device Information.................................................................... 89

3.5.2 Wireless Clients........................................................................ 91

3.5.3 DHCP Clients............................................................................ 91

3.5.4 Logs .......................................................................................... 91

3.5.5 Statistics.................................................................................... 92

3.5.6 Route information ..................................................................... 94

3.5.7 Logout....................................................................................... 94

1

1 Overview

The ADN-4100 supports multiple line modes. It provides four 10/100Base-TX

Ethernet interfaces at the user end. The device provides high speed ADSL

broadband connection to the Internet or Intranet for high-end users, such as net

cafes and office users. It provides high performance access to the Internet,

downstream up to 24 Mbps and upstream up to 1 Mbps.

The device supports WLAN access. It can connect to the Internet through a

WLAN AP or WLAN device. It complies with IEEE 802.11, 802.11b/g/n

specifications, WEP, WPA, and WPA2 security specifications.

1.1 Safety Precautions

Refer to the following instructions to prevent the device from risks and damage

caused by fire or electric power:

Use volume labels to mark the type of power.

Use the power adapter packed within the device package.

Pay attention to the power load of the outlet or prolonged lines. An

overburden power outlet or damaged lines and plugs may cause electric

shock or fire accident. Check the power cords regularly. If you find any

damage, replace the power cords at once.

Proper space left for heat dissipation is necessary to avoid damage caused

by overheating to the device. The long and thin holes on the device are

designed for heat dissipation to ensure that the device works normally. Do

not cover these heat dissipation holes.

Do not put this device close to a place where a heat source exits or high

temperature occurs. Avoid the device from direct sunshine.

Do not put this device close to a place where it is over damp or watery. Do

not spill any fluid on this device.

Do not connect this device to any PCs or electronic products, unless our

customer engineer or your broadband provider instructs you to do this,

because any wrong connection may cause power or fire risk.

Do not place the device on an unstable surface or support.

1.2 LEDs and Interfaces

Front Panel

Figure 1 Front panel

The following table describes the LEDs of the device.

2

LED Color Status Description

On

The device is powered on and the

initialization is normal.

Green

Off The power is off.

PWR

Red On

The device is self-testing or self-testing is

failed.

Slow

Blinks

No signal is detected.

Fast

Blinks

The device is handshaking with the physical

layer of the office.

Link Green

On

The device is connected to the physical

layer of the office.

On

The Internet connection is normal in the

routing mode (for example: PPP dial-up is

successful), and no Internet data is being

transmitted.

Blinks

Internet data is being transmitted in the

routing mode.

Green

Off The device is in the bridge mode.

Data

Red On

The Internet connection fails after

successful synchronization in the routing

mode (for example: PPP dial-up is failed).

On The LAN connection is normal. LAN4-1 Green

Blinks

Data is being transmitted through the LAN

interface, or the Internet data is being

LED Color Status Description

transmitted in the bridge mode.

Off The LAN connection is not established.

On The WLAN connection has been activated.

Blinks

Data is being transmitted through the

WLAN interface.

WLAN Green

Off The WLAN connection is not activated.

Blinks

WPS is activated and the device is waiting

for negotiation with the clients.

WPS Green

Off WPS is not activated.

Rear Panel

Figure 2 Rear panel

The following table describes the interfaces and buttons of the device.

Interface/Button Description

LINE

RJ-11 interface, for connecting the interface of the

telephone set through the telephone cable.

LAN1, LAN2,

LAN3, LAN4

RJ-45 interface, for connecting the Ethernet interface of a

computer or an Ethernet device.

POWER

Power interface, for connecting the interface of the power

adapter.

RESET

Restore to factory defaults. To restore factory defaults,

keep the device powered on, push a paper clip into the

hole to press the button for over 3 seconds and then

release.

WPS/ WLAN

Press the button and hold it for 1 second, to enable

WLAN.

Press the button and hold it for 1 second to 3

3

4

Interface/Button Description

seconds, it does not take effect.

Press the button and hold it for 3 or more than 3

seconds, to initialize WPS negotiation.

ON/OFF Power switch, power on or off the device.

1.3 System Requirements

Recommended system requirements are as follows:

A 10Base-T/100Base-TX Ethernet card is installed on your PC.

A hub or switch is available for connecting one Ethernet interface on the

device and several PCs.

Operating system: Windows XP, Windows 2000, Windows ME, or Windows

98SE.

Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or Firefox 1.5 or

higher

1.4 Features

The device supports the following features:

IEEE802.11b/g/n

Various line modes

External PPPoE dial-up access

Internal PPPoE and PPPoA dial-up access

1483 Bridged, 1483 Routed, and MER access

Multiple PVCs (up to eight) that can be isolated from each other

A single PVC with multiple sessions

Multiple PVCs with multiple sessions

Binding of ports with PVCs

802.1Q and and 802.1P protocol

DHCP server

NAT and NAPT

Static routing

Firmware upgrade through Web or TFTP

5

Restore to the factory defaults

DNS

Virtual server

DMZ

Three-level user accounts

Web user interface

Telnet CLI

System status displaying

PPP session PAP, CHAP, and MS-CHAP

IP filter

IP QoS

Remote access control

Line connection status test

Remote management through telnet or HTTP

Backup and restoration of configuration file

Ethernet interface supports crossover detection, auto-correction and

polarity correction

UPnP

PPTP VPN

IPSec VPN

2 Hardware Installation

Step 1 Connect the LINE interface of the device and the Modem interface of

the splitter with a telephone cable. Connect the phone set to the

Phone interface of the splitter through a telephone cable. Connect the

input cable to the Line interface of the splitter.

The splitter has three interfaces:

Line: Connect to a wall phone interface (RJ-11 jack).

Modem: Connect to the LINE interface of the device.

Phone: Connect to a telephone set.

Step 2 Connect the LAN interface of the device to the network card of the PC

through an Ethernet cable (MDI/MDIX).

Note:

Use the twisted-pair cable to connect the hub or switch.

Step 3 Insert one end of the power adapter to the wall outlet and connect the

other end to the POWER interface of the device.

Connection 1: Figure 3 shows the connection of the device, PC, splitter, and

telephone sets, when no telephone set is placed before the splitter. This type of

connection is recommended.

6

Figure 3 Connection diagram (without a telephone set before the splitter)

Connection 2: Figure 4 shows the connection of the device, PC, splitter, and

telephone sets, when a telephone set is placed before the splitter.

As illustrated in the following figure, the splitter is installed close to the device:

Figure 4 Connection diagram (with a telephone set before the splitter)

Note:

When connection 2 is used, the filter must be installed close to the telephone

cable. See Figure 4. Do not use a splitter to replace the filter.

Installing a telephone directly before the splitter may lead to failure of connection

between the device and the central office, failure of Internet access, or slow

connection speed. If you need to add a telephone set before the splitter, you must

add a microfilter before the telephone set. Do not connect several telephones

before the splitter or connect several telephones with the microfilter.

7

3 Web Configuration

This chapter describes how to configure the device by using the Web-based

configuration utility.

3.1 Accessing the Device

The following describes how to access the device for the first time in detail.

Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1

in the address bar.

Step 2 The LOGIN page as shown in the following figure appears:

In this page, enter the user name and the password. Then, click login.

The user name and the password of the super user are admin and admin

respectively.

The user name and the password of the normal user are user and user

respectively.

If you log in as the super user successfully, the page as shown in the following

figure appears:

8

If the login information is incorrect, the page as shown in the following figure

appears:

Click OK to log in again.

Note:

In the LAN, you can use either of the following two levels of user accounts

(displayed in the user name/password format) to access the device:

admin/admin and user/user.

In the WAN, you can use one of the following three levels of user accounts

(displayed in the user name/password format) to access the device:

admin/admin, user/user, and support/support.

3.2 General Configuration

9

3.2.1 Wizard

Wizard helps you to fast and accurately configure Internet connection and other

important parameters. The following sections describe these various

configuration parameters.

When subscribing to a broadband service, be aware of the Internect connection

mode. The physical WAN device can be Ethernet, DSL, or both. Technical

information about properties of Internet connection is provided by your Internet

service provider (ISP). For example, your ISP should inform you whether you are

connected to the Internet using a static or dynamic IP address, and the protocol,

such as PPPoA or PPPoE, that you use to communicate on the Internet.

Step 1 Choose Setup > Wizard. The page as shown in the following figure

appears:

Step 2 Click Setup Wizard. The page as shown in the following figure

appears:

10

There are four steps to configure the device. Click Next to continue.

Step 3 Set the time and date. Then, click Next.

Step 4 Configure the Internet connection.

Select the protocol and the encapsulation mode. Set the VPI and the

VCI.

If the Protocol is set to PPPoE or PPPoA, the page as shown in the

following figure appears:

11

You need to enter the user name and password for PPPoE or PPPoA

dialup.

If the Protocol is set to Dynamic IP, the page as shown in the

following figure appears:

12

If the Protocol is set to Static IP, the page as shown in the following

figure appears:

You need to enter the information of the IP address, subnet mask, and

gateway.

If the Protocol is set to Bridge, the page as shown in the following

figure appears:

13

If you click Scan, the system automatically searches the available

PVCs.

After the searching is complete, the result appears next to the Scan

button.

14

Page is loading ...

Planet ADN-4100 Owner's manual

Related papers

Other documents