2. Computers & electronics
  3. Networking
  4. NEC
  5. 2400 ipx

NEC 2400 ipx, NEAX 2400 IPX IPTRK Circuit Card System User manual

  • Hello! I am an AI chatbot trained to assist you with the NEC 2400 ipx User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
NOVEMBER, 2000
NEC America, Inc.
NDA-24318
ISSUE 1
STOCK # 200818
IPTRK Circuit Card System Manual
®
LIABILITY DISCLAIMER
NEC America, Inc. reserves the right to change the specifications, functions, or
features, at any time, without notice.
NEC America, Inc. has prepared this document for use by its employees and
customers. The information contained herein is the property of NEC America,
Inc. and shall not be reproduced without prior written approval from NEC
America, Inc.
NEAX
®
and D
term®
are registered trademarks of NEC Corporation.
Cisco
®
is a registered trademark of Cisco Systems, Inc. Documentation
references to Cisco products refer to networking with Cisco hardware.
Copyright 2000
NEC America, Inc.
Printed in the U.S.A.
ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4
DATE NOVEMBER, 2000 DATE DATE DATE
ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8
DATE DATE DATE DATE
NEAX2400 IPX
IPTRK Circuit Card System Manual
Revision Sheet 1/1
NDA-24318
PAGE No.
ISSUE No.
12345678
i 1
ii 1
iii 1
iv
1
1 1
2 1
3 1
4
1
5 1
6 1
7 1
8 1
9 1
10 1
11 1
12
1
13 1
14 1
15 1
16
1
17 1
18 1
19 1
20
1
21 1
22 1
23 1
24 1
25 1
26 1
27 1
28
1
29 1
30 1
31 1
32
1
33 1
34 1
35 1
36
1
37 1
38 1
39 1
40
1
41 1
42 1
43 1
44
1
45 1
46 1
47 1
48
1
49 1
50 1
PAGE No.
ISSUE No.
12345678
NDA-24318
ISSUE 1
NOVEMBER, 2000
NEAX2400 IPX
IPTRK Circuit Card System Manual
TABLE OF CONTENTS
Page
NDA-24318 TABLE OF CONTENTS
Page i
Issue 1
CHAPTER 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. SERVICE FEATURES TO BE PROVIDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. HOW TO FOLLOW THIS MANUAL AND RELATED REFERENCE MANUALS . . . . . . . . . . . . . . . . . . 6
3.1 How to Follow This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Related Reference Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CHAPTER 2 CIRCUIT CARD EXPLANATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. PA-8IPTB (IPTRK Circuit Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 General Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Mounting Location/Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Face Layout of Lamps, Switches and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Lamp Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5 Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6 External Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.7 Switch Setting Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3. PZ-8VCTB (Sub Board) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1 General Function/Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2 Lamp Indications and Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CHAPTER 3 OFFICE DATA PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2. CCIS NETWORKING VIA IP [C-163] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1 Required Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.2 Required Hardware (Point-to-Multipoint Connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.3 Service Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.4 Data Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3. FCCS NETWORKING VIA IP [F-36] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.1 Required Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2 Required Hardware (Point-to-Multipoint Connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.3 Service Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.4 Data Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CHAPTER 4 OPERATION TESTS AFTER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2. CCIS NETWORKING VIA IP [C-163]/VOICE OVER IP (H.323) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3. FCCS NETWORKING VIA IP [F-36] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
LIST OF FIGURES NDA-24318
Page ii
Issue 1
LIST OF FIGURES
Page
Figure 1-1 Example Network Configuration via Intranet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 1-2 Outer View of IPTRK Circuit Card Furnished with a Sub Board (PZ-8VCTB) . . . . . . . . . . . . . . 1
Figure 1-3 Block Diagram - CCIS Networking via IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 1-4 Block Diagram - CCIS Networking via IP [Point-to-Multipoint Connection] . . . . . . . . . . . . . . . . 4
Figure 1-5 Block Diagram - FCCS Networking via IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 2-1 Location of PA-8IPTB (IPTRK Circuit Card) within the System . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 2-2 PA-8IPTB Circuit Card Mounting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 2-3 Port Assignment for PA-8IPTB Circuit Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 2-4 Face Layout of PA-8IPTB IPTRK Circuit Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 2-5 Ethernet Cable Connection for CCIS Networking via IP [C-163] . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2-6 Ethernet Cable Connection for FCCS Networking via IP [F-36]
[IPTRK: Point-to-Multipoint] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 2-7 Attachment of Sub Board (PZ-8VCTB) onto IPTRK Circuit Card . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 2-8 Outer View of PZ-8VCTB on the Main Board of PA-8IPTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 3-1 Overview of CCIS Networking via IP [C-163] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 3-2 Example of Required Hardware for CCIS Networking via IP [C-163] . . . . . . . . . . . . . . . . . . . . 20
Figure 3-3 Port Assignment of Bch for CCIS Tie Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 3-4 Example Data Assignment (ACSC/ACIC2) CCIS - CCIS Networking via IP [C-163] . . . . . . . . 26
Figure 3-5 Example Assignment of IP Addresses of IPTRK Circuit Card and Connected Router . . . . . . . 28
Figure 3-6 Overview of FCCS Networking via IP [F-36] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 3-7 Example Required Hardware for FCCS Networking via IP [F-36] . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 3-8 Example Required Hardware for FCCS Networking via IP [F-36]
[IPTRK: Point-to-Multipoint] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 3-9 Example Data Assignment (ACRD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 3-10 Example Data Assignment (ACTK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 3-11 Example Assignment of FCHN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 3-12 Example Assignment of Destination IP and Next IP (AETH) . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 3-13 Example Data Assignment (ACAN/AFRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 3-14 Example Assignment of IP Addresses of IPTRK Circuit Card and Connected Router . . . . . . . 41
Figure 3-15 FCCS Networking via IP [F-36] [Point-to-Multipoint Connection] Example Data Sheet 1 . . . . . 42
Figure 3-16 FCCS Networking via IP [F-36] Example Data Sheet 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-17 FCCS Networking via IP [F-36] and FCH FCCS Networking
(both ASPC and AETH commands) Example Data Sheet 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 3-18 FCCS Networking via IP [F-36] - FCCS Network via IP Tandem Connection
(AFPC Dummy Data) Example Data Sheet 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3-19 FCCS Networking via IP [F-36] and FCH FCCS Networking
(AFPC or AETH commands) Example Data Sheet 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 4-1 Lamps to be Tested (CCIS Networking via IP [C-163]) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 4-2 Lamps to be Tested (FCCS Networking via IP [F-36] [Point-to-Multipoint Connection]) . . . . . . 49
NDA-24318 LIST OF TABLES
Page iii
Issue 1
LIST OF TABLES
Page
Table 1-1 Specification of IP Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 2-1 Lamp Indication Meanings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 2-2 Switch Setting Meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 2-3 PAD Values of µ-law Pattern 1 / Pattern 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 2-4 Switch Setting Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 3-1 Internode Service Features (CCIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 3-2 Alternate Routing to be Provided/Not Provided (FCCS Networking via IP [F-36]). . . . . . . . . . . 34
Table 3-3 PBX Software/IPTRK Circuit Card Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
LIST OF TABLES NDA-24318
Page iv
Issue 1
This page is for your notes.
NDA-24318 CHAPTER 1
Page 1
Issue 1
INTRODUCTION
CHAPTER 1 INTRODUCTION
1. GENERAL
This manual explains the installation of the following IPTRK circuit cards, which are used to send/receive voice
or FAX (G3) information via the Intranet. Although PA-8IPTB is equipped with a total of eight ports, an
optional sub board (PZ-8VCTB) provides an additional eight ports, when mounted on a PA-8IPTB main board.
• PA-8IPTB (with eight ports)
• PZ-8VCTB (optional daughter board provides an additional eight ports to PA-8IPTB)
Figure 1-1 Example Network Configuration via Intranet
Note:
A single sub board can be mounted on PA-8IPTB, two slots are physically occupied.
Figure 1-2 Outer View of IPTRK Circuit Card Furnished with a Sub Board (PZ-8VCTB)
Table 1-1 Specification of IP Trunk
FUNCTION SPECIFICATION REMARKS
Voice Encoding/Decoding
G.729a 8 kbps CS-ACELP
G.711 PCM of Voice Frequencies
G.723.1
Dual rate Speech Coder for
Multimedia Communication
transmitting at 5.3 and 6.3 kbits/s
• IPTRK: PA-8IPTB:
Line/Trunk circuit card featuring Voice over IP
Maximum of 16ch (equipped with 8ch CODEC)
Equipped with FCCS/CCIS handler
Mounting capacity: 2 per UNIT (4 per PIM)
• Sub Board: PZ-8VCTB
8ch CODEC daughter board for PA-8IPTB expansion (optional)
Note
IPTRK
IPTRK
IP Packet
IP Packet
Intranet
NEAX2400 IPX
NEAX2400 IPX
TCP/IP TCP/IP
LAN
LAN
10 BASE-T/100 BASE-TX
IPTRK (PA-8IPTB)
PZ-8VCTB
(Sub Board - Optional)
POWER
Router
POWER
Router
Sub Board (eight port option)
IPTRK (Eight Ports)
FCON (For Ether cable)
IPCON (For Ether cable)
CHAPTER 1 NDA-24318
Page 2
Issue 1
INTRODUCTION
Note 1: Transmission speed is within 14.4 kbps.
Note 2: On a conference call via IPTRK, Echo Canceller cannot be activated when using certain kinds of telephone
sets (generally analog telephones).
2. SERVICE FEATURES TO BE PROVIDED
When using an IPTRK circuit card, the following services are available:
• CCIS Networking via IP [C-163]
• FCCS Networking via IP [F-36]
FAX FAX Relay (T.30)
G3 FAX (V.17, V.21, V.27ter, V.29,
V.33) is available
Super G3 (V.34, etc.) is not available
Note 1
INTER-OFFICE SIGNAL LINK
MP: Point-to-Multipoint
NEAX2400 IPX → NEAX2400 IPX
FCCS MP
CCIS MP
NEAX2400 IPX → NEAX2000 IVS
2
CCIS MP
Jitter Dynamic Jitter Buffer Buffer Value (40 ~ 300 ms)
LAN Interface 10 BASE-T (100 BASE-TX)
QoS (Quality of Service) WFQ by ToS Use Cisco
®
router
Echo Canceller G.168 Round Trip Delay = 32 ms
Note 2
Table 1-1 Specification of IP Trunk (Continued)
FUNCTION SPECIFICATION REMARKS
NDA-24318 CHAPTER 1
Page 3
Issue 1
INTRODUCTION
Figure 1-3 represents a block diagram example of CCIS Networking via IP [C-163]. For more detailed
information, see CHAPTER 3.
Figure 1-3 Block Diagram - CCIS Networking via IP
Note:
As shown, the IPTRK circuit cards in the self-node and its connected node must be 1-to-1 ratio.
Intranet
POWER
Router
POWER
Router
Symbols:
IPTRK: IP Trunk
: Ethernet cable
IPTRK
IPTRK
IPTRK
IPTRK
IPTRK
Both Speech and Signal
Node A Node B
Both Speech and Signal
Node C
Both Speech and Signal
CPU
CPU
CPU
POWER
Router
IPTRK
CHAPTER 1 NDA-24318
Page 4
Issue 1
INTRODUCTION
Figure 1-4 represents a block diagram example of CCIS Networking via IP [C-163] when an IPTRK circuit card
in Node A is connected to the IPTRKs of Node B and C (Point-to-Multipoint connection). For more detailed
information, see CHAPTER 3.
Figure 1-4 Block Diagram - CCIS Networking via IP [Point-to-Multipoint Connection]
Note:
As shown, an IPTRK circuit card, accommodated in a node, can be connected to the IPTRK circuit cards
of multiple nodes, thus achieving Point-to-Multipoint connection.
POWER
Router
POWER
Router
IPTRK
IPTRK
IPTRK
To IPTRK of Node C
Node A Node B
Both Speech and Signal
Both Speech and Signal
CPU
CPU
Both Speech and Signal
CPU
Symbols:
IPTRK: IP Trunk
:Ethernet Cable (Both Speech and Signal)
Node C
To IPTRK of Node B
Point-to-Multipoint Connection
Intranet
POWER
Router
NDA-24318 CHAPTER 1
Page 5
Issue 1
INTRODUCTION
Figure 1-5 represents a block diagram example of FCCS Networking via IP [F-36]. For more detailed
information, see CHAPTER 3.
Figure 1-5 Block Diagram - FCCS Networking via IP
Note:
As shown, the IPTRK circuit cards in the self-node and its connected node must be 1-to-1 ratio.
POWER
Router
POWER
Router
IPTRK
IPCON
FCON
IPTRK
IPCON
FCON
Both Speech and Signal
Both Speech and Signal
IPTRK
IPCON
FCON
IPTRK
IPCON
FCON
Node A Node B
IPTRK
IPCON
FCON
IPTRK
IPCON
FCON
Both Speech and Signal
FCCS Signal
CPU LANI
HUB
FCCS Signal
Node C
CPU
LANI
HUB
FCCS Signal
CPU
LANI
HUB
Symbols:
IPTRK: IP Trunk
LANI: LAN Interface (PZ-PC19)
:10 BASE-T Cable (Both Speech and Signal)
: 10 BASE-T Cable (for FCCS signal)
Intranet
POWER
Router
CHAPTER 1 NDA-24318
Page 6
Issue 1
INTRODUCTION
3. HOW TO FOLLOW THIS MANUAL AND RELATED REFERENCE MANUALS
This manual describes only items related to the IPTRK circuit cards. Therefore, if you need details on the
NEAX2400 IPX, the FCCS network, or the CCIS network, please refer to the related manual. Configuration of
this manual and related reference manuals are shown below.
3.1 How to Follow This Manual
• CHAPTER 1 INTRODUCTION
This chapter explains the purpose of this manual.
• CHAPTER 2 CIRCUIT CARD EXPLANATIONS
This chapter explains the functional outline, mounting location, switch and lamp meanings, and
external interfaces of the IPTRK circuit card.
• CHAPTER 3 OFFICE DATA PROGRAMMING
This chapter explains details on general descriptions, service conditions, and data programming of the
IPTRK-related service features.
• CHAPTER 4 OPERATION TESTS AFTER INSTALLATION
This chapter explains the procedure to verify normal operation of the IPTRK circuit card when
installation and necessary data settings have been completed.
3.2 Related Reference Manuals
For more detailed information on the NEAX2400 IPX, the FCCS network, or the CCIS network, refer to
the following manuals:
For details on NEAX2400 IPX:
• NEAX2400 IPX Installation Manual
• NEAX2400 IPX Circuit Card Manual
• NEAX2400 IPX Office Data Specification
• NEAX2400 IPX Feature Programming Manual
• NEAX2400 IPX System Operations and Maintenance Manual
For details on the FCCS network:
• NEAX2400 IPX Fusion System Manual
For details on the CCIS network:
• NEAX2400 IPX No. 7 CCIS System Manual
NDA-24318 CHAPTER 2
Page 7
Issue 1
CIRCUIT CARD EXPLANATIONS
CHAPTER 2 CIRCUIT CARD EXPLANATIONS
1. GENERAL
This chapter provides detailed explanations for the following circuit cards:
• PA-8IPTB
• PZ-8VCTB
2. PA-8IPTB (IPTRK Circuit Card)
2.1 General Function
PA-8IPTB is a Line/Trunk circuit card that is used for providing CCIS/FCCS service via the Intranet, and
to send/receive voice or FAX (G3) information over IP. PA-8IPTB is equipped with a total of eight ports,
however, an optional sub board (PZ-8VCTB) provides an additional eight ports, when mounted on a PA-
8IPTB main board. For more detailed information, see Section 2.6 External Interfaces. This card provides
the following functions:
a.) Voice Data Processing:
• Voice data compression/decompression
• FAX data encoding/multiplexing
• DTMF (analog signal) detection/transmission
• Echo Canceller
b.) IP Network Interface (10/100 Mbps Ethernet interface to send/receive voice/signal information)
c.) FCCS Link Interface
d.) LP-PM Bus Interface (for PM bus dedicated to NEAX2400 IPX series)
Figure 2-1 Location of PA-8IPTB (IPTRK Circuit Card) within the System
Note 1:
When using an IPTRK circuit card for CCIS Networking via IP [C-163], the IPTRK cards in the self node
and its connected node must be in 1-to-1 ratio.
Note 2: Used for FCCS only.
Caution:While this circuit card is in use, some LSIs may get hot. Handle this card with care. Do not touch the heated
LSI surfaces.
Ethernet Cable
Intranet
CCIS/FCCS Speech
CCIS/FCCS Signal
MUX
Ethernet Cable
Symbols:
IPTRK: IP Trunk
MUX: Multiplexer
TSW: Time Division Switch
ISAGT: ISA Gate
LANI: LAN Interface
: Speech
: Signal
IPTRK
IPCON
FCON
HUB
Note 1
LANI
CPU
TSW
ISAGT
FCCS Signal
Note 2
POWER
Router
CHAPTER 2 NDA-24318
Page 8
Issue 1
CIRCUIT CARD EXPLANATIONS
2.2 Mounting Location/Condition
Mounting location/condition of this card is shown below. Mount this card in the following shaded slots:
Figure 2-2 PA-8IPTB Circuit Card Mounting Locations
Mounting conditions of this card are as follows:
• When this card is used without a sub board (PZ-8VCTB), and mounted in any of the universal slots 05,
07, 09, 16, 18 or 20:
Although this card physically occupies only one slot, actual ports to be used are those in the even-
numbered group of only the left side of the slot (see Figure 2-3).
• When this card is used without a sub board (PZ-8VCTB), and mounted in any of the universal slots 10,
11, 12, 21, 22 or 23:
This card occupies only one slot. In regard to the port accommodation, see Figure 2-3.
• When this card is used with a sub board (PZ-8VCTB):
This card physically occupies a total of two slots. In regard to the port accommodation, see Figure 2-3.
• One UNIT accommodates a maximum of two IPTRK circuit cards (slots 04~12 / slots 15~23).
Therefore, the third IPTRK circuit card must be accommodated in a different UNIT of the same/other
PIM.
00 01 02 03 04 05 06 07 08 09 10 11 13 14 15 16 17 18 19 20 21 22 2312
PIM
Universal Slots
Universal Slots
NDA-24318 CHAPTER 2
Page 9
Issue 1
CIRCUIT CARD EXPLANATIONS
Figure 2-3 Port Assignment for PA-8IPTB Circuit Card
PWR
PWR
Ex. Slot 05
Ex. Slot 21
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
0810
12
13
14
16
17
18
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
P
Z
-
8
V
C
T
B
01
00
03
02
05
04
07
06
09
08
11
10
12131415
16171819
20
212223
01 00
03 02
05 04
07 06
09 08
11 10
12131415
16171819
20212223
01 00
03 02
05 04
07 06
09 08
11 10
12131415
16171819
212223
01 00
03 02
05 04
07 06
09 08
11 10
12131415
16171819
20212223
Examples of PA-8IPTB port accommodation:
• Not equipped with Sub Board (PZ-8VCTB)
• Equipped with one Sub Board (PZ-8VCTB)
• PA-8IPTB not equipped with Sub Board (PZ-8VCTB)
8 Ports
16 Ports
• PA-8IPTB is equipped with one Sub Board (PZ-8VCTB)
PA-8IPTB in a 16 port slot
PA-8IPTB in a 32 port slot
PIM
CHAPTER 2 NDA-24318
Page 10
Issue 1
CIRCUIT CARD EXPLANATIONS
2.3 Face Layout of Lamps, Switches and Connectors
The face layout of lamps, switches and connectors on this circuit card are shown below. For more detailed
information, see Section 2.6 External Interfaces.
Figure 2-4 Face Layout of PA-8IPTB IPTRK Circuit Card
Note:
When mounting the optional sub board (PZ-8VCTB), be sure to use SUB3A and SUB3B connectors.
2.4 Lamp Indications
Lamp indication meanings are shown below:
Table 2-1 Lamp Indication Meanings
LAMP NAME COLOR MEANING OF INDICATION
OPE Green Lights when circuit card is operating normally.
BUSY Green Lights when one or more lines are busy.
SUBOPE3 Green Lights when Sub CPU #3 is in operation.
SUBOPE2 Green Lights when Sub CPU #2 is in operation.
SUBOPE1 Green Lights when Sub CPU #1 is in operation.
SUBOPE0 Green Lights when CPU of IPTRK circuit card’s main board is in operation.
L3 Green Not used.
L2 Green Not used.
L1 Green Lights when CCIS/FCCS link is established.
IP-LRR Green Lights when this card is used with IP network.
12345678
SUBOPE3
SUBOPE2
SUBOPE1
SUBOPE0
BUSY
L3
L2
L1
IP-TXRX
IP-100M
F-TXRX
F-100M
IP-LRR
IP-LINK
IP-COL
F-LRR
F-LINK
F-COL
SW10
12345678
SW40
12345678
SW20
12345678
SW50
12345678
SW30
12345678
SW60
OPE
MODE
IPCON
FCON
MB
MBR
SUB3A
SUB3B
NDA-24318 CHAPTER 2
Page 11
Issue 1
CIRCUIT CARD EXPLANATIONS
2.5 Switch Settings
The meaning of each switch on this card is shown below:
IP-LINK Green Lights when establishing a connection (physically) with the IP network.
IP-TXRX Green Lights when sending/receiving data packets.
IP-100M Green Lights when 100 Mbps interface is in use.
IP-COL Yellow Lights when data packet collision is detected.
F-LRR Green Lights when this card is used with FCCS network.
F-LINK Green Lights when establishing a connection (physically) with the FCCS network.
F-TXRX Green Lights when sending/receiving data packets.
F-100M Green Lights when 100 Mbps interface is in use.
F-COL Yellow Lights when data packet collision is detected.
Table 2-2 Switch Setting Meanings
SWITCH
NAME
SWITCH
NUMBER
SETTING
STANDARD
SETTING
MEANING
MB
- ON (UP) Circuit Card: Make-Busy.
- OFF (DOWN)
× Circuit Card: Make-Busy Cancel.
MBR
- ON (UP) Circuit Card Make-Busy Request.
- OFF (DOWN)
× Circuit Card Make-Busy Request Cancel.
MODE
-0
× Auto Negotiation ON (standard setting).
- 1 Auto Negotiation OFF.
- 2 MAC Address Writing Mode.
-3-F Not used.
Table 2-1 Lamp Indication Meanings (Continued)
LAMP NAME COLOR MEANING OF INDICATION
CHAPTER 2 NDA-24318
Page 12
Issue 1
CIRCUIT CARD EXPLANATIONS
SW10
1
ON External Ether 100 Mbps: Fixed
Note 1
OFF × External Ether 10 Mbps: Fixed Note 1
2
ON Internal Ether 100 Mbps: Fixed
Note 1
OFF × Internal Ether 10 Mbps: Fixed Note 1
3~5
PAD Pattern Selection
For details on each PAD value, refer to Table 2-1.
6
ON PAD is assigned by ARTD/ACRD
Note 2
OFF × PAD is assigned by APAD/AFPD Note 2
7
ON Flexible PAD is used.
OFF
× Flexible PAD is not used.
8OFF
×
Echo Canceller nonlinear processor is not used. (Fixed
to OFF.)
Note 1: Valid when MODE switch is set to 1 (= Automatic Negotiation OFF).
Note 2: When SW10-6 is ON, PAD value is set as specified by ARTD (for CCIS) or ACRD (for FCCS). PAD
value specified by APAD (for CCIS) or AFPG (for FCCS) is not effective in this configuration.
When SW10-6 is OFF, PAD value is set as specified by ARTD (for CCIS) or ACRD (for FCCS) as
default. However, when any data has been set by the APAD or AFPD command, the specified PAD
value is used. The standard setting is OFF.
Table 2-2 Switch Setting Meanings (Continued)
SWITCH
NAME
SWITCH
NUMBER
SETTING
STANDARD
SETTING
MEANING
SW10-3 SW10-4 SW10-5 PAD PATTERN SELECTION
OFF OFF OFF Not used
ON OFF OFF Not used
OFF ON OFF µ-law Pattern 1 (for North America)
ON ON OFF µ-law Pattern 2 (for North America)
OFF OFF ON Not used
ON OFF ON Not used
OFF ON ON Not used
ON ON ON Not used
NDA-24318 CHAPTER 2
Page 13
Issue 1
CIRCUIT CARD EXPLANATIONS
SW20
1~6
Designation of Flexible PAD Value
Note 1
7
ON
Fixed to OFF.
OFF
×
8
ON
Fixed to OFF.
OFF
×
Table 2-2 Switch Setting Meanings (Continued)
SWITCH
NAME
SWITCH
NUMBER
SETTING
STANDARD
SETTING
MEANING
SW20
-1
SW20
-2
SW20
-3
SW20
-4
SW20
-5
SW20
-6
PAD
VALUE
OFF OFF OFF OFF OFF OFF 16 [dB]
ON OFF OFF OFF OFF OFF 15 [dB]
OFF ON OFF OFF OFF OFF 14 [dB]
ON ON OFF OFF OFF OFF 13 [dB]
OFF OFF ON OFF OFF OFF 12 [dB]
ON OFF ON OFF OFF OFF 11 [dB]
OFF ON ON OFF OFF OFF 10 [dB]
ON ON ON OFF OFF OFF 9 [dB]
OFF OFF OFF ON OFF OFF 8 [dB]
ON OFF OFF ON OFF OFF 7 [dB]
OFF ON OFF ON OFF OFF 6 [dB]
ON ON OFF ON OFF OFF 5 [dB]
OFF OFF ON ON OFF OFF 4 [dB]
ON OFF ON ON OFF OFF 3 [dB]
OFF ON ON ON OFF OFF 2 [dB]
ON ON ON ON OFF OFF 1 [dB]
OFF OFF OFF OFF ON OFF 0 [dB]
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/