Typar ATFLH-003 Installation guide

Brand
Typar
Model
ATFLH-003
Type
Installation guide

Typar ATFLH-003 is a self-adhering window flashing designed for curved applications. It is easy to install, simply cut the flashing to the desired size and peel off the release paper to expose the adhesive backing. Then, press the flashing into place and seal the edges with Typar Construction Tape. Typar ATFLH-003 is a durable and weather-resistant flashing that will help to protect your windows from the elements.

Typar ATFLH-003 is a self-adhering window flashing designed for curved applications. It is easy to install, simply cut the flashing to the desired size and peel off the release paper to expose the adhesive backing. Then, press the flashing into place and seal the edges with Typar Construction Tape. Typar ATFLH-003 is a durable and weather-resistant flashing that will help to protect your windows from the elements.

SELF-ADHERING WINDOW FLASHING
TYPAR
®
FLEXIBLE FLASHING
TYPAR
®
FLEXIBLE FLASHING-
T YPICAL INSTALL ATION
STEP 1
Cut horizontal slits where the curve starts on the window, out to
a distance equal to the width of flashing used. Continue at a 45
degree angle upwards until you are above the top center of the
window by at least the width of the flashing. Temporarily tape
this flap up out of the way.
STEP 2
Cut a strip of TYPAR
®
Peel and Stick Flashing to extend past the
edges of the rough opening on both sides by a little less than
the width of the side (jamb) flashing to be installed in step #4.
Using the release paper as a guide slowly peel back the release
paper and press in place
STEP 3
Apply a continuous bead of sealant around the interior edge of
the window's nailing flange at, or just inside, the manufacturer's
nailing slots or holes. Nail the window in place according to
manufacturer's instructions.
CONTINUED ON REVERSE.
FOR CURVED APPLICATIONS
© 2017, Berry Plastics Corporation.
TYPAR
®
is a registered trademark of Berry Plastics Corporation or its affiliate.
Please visit TYPAR.com for installation instructions and warranty information.
Building Wraps | Flashings | Construction Tape | Fasteners
TYPAR
®
FLEXIBLE FLASHING - INSTALLATION GUIDE
02
STEP 4
Cut two strips for the sides (jambs) of the window that cover
the width of the previously installed flashing at the base. Slowly
peel the release paper off as you press the flashing in place.
Insure the flashing covers all nails and mounting slots on the
window's mounting flange.
STEP 5
Cut a piece of TYPAR Flexible Flashing for the head of the
window that is the length of the curve plus two times the width
of the flashing. Slowly peel the release paper and press the
edge next to the window frame. Cover all nails and mounting
slots.
STEP 6
Fold down the flap (from step #1) over the head flashing and
tape the horizontal and diagonal slits with TYPAR
®
Construction
Tape.
NOTE: All installation procedures and techniques must comply
with local code requirements and latest version of ASTM 2112.
Installation methods approved by the American Architectural
Manufacturers Association (AAMA) are acceptable for TYPAR
®
products and TYPAR
®
Weather Protection System limited warranty.
WARNING: Flashing will not address the water intrusion which
may occur through the window itself.
For more information, visit TYPAR.com.
3393
  • Page 1 1
  • Page 2 2

Typar ATFLH-003 Installation guide

Brand
Typar
Model
ATFLH-003
Type
Installation guide

Typar ATFLH-003 is a self-adhering window flashing designed for curved applications. It is easy to install, simply cut the flashing to the desired size and peel off the release paper to expose the adhesive backing. Then, press the flashing into place and seal the edges with Typar Construction Tape. Typar ATFLH-003 is a durable and weather-resistant flashing that will help to protect your windows from the elements.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents