Evolve Communications RD5000 User manual

User’s Manual RD5000

*

This changes everything!

SM

1

*Trademark

Table of Contents

Introduction

1. Evolve GUIDE Remote*

2. Computer Requirements

3. Key Descriptions

a. Key Layout

b. Key Function Descriptions

Getting Started

1. Activate Remote Control

a. Install Batteries

b. Install RemoteLinker* Software

c. Connect RemoteLinker Cable

2. Start RemoteLinker Software

3. Activate Remote Control at Website

4. Sync Remote Control

5. Setup Remote Control

a. Setup a TV

b. Setup Other Devices

c. Remove a Device

6. Setup DirecTune*

a. Determining DirecTune Device

b. Setup DirecTune Device

Using the Remote

1. Channel Screen

2. Changing Modes

3. Using the GUIDE Key

a. Accessing Program Listings, Suggestions and Reminders

b. Program Listings

Browsing and Tuning

Quick Browse

c. Program Descriptions

Accessing and Tuning

Quick Browse

d. Suggestions

e. Reminders

Reminders Notification

Accessing the Reminders List

Personal Reminders

4. Using Interactivity Keys

a. Interactivity Keys

b. Interactivity Offers

c. Browsing Interactivity Offers

Table of Contents

3

4

5

6

8

9

10

11

12

13

15

19

20

21

25

26

27

28

29

30

31

32

33

34

35

36

37

39

2

*Trademark

Table of Contents

5. Using the MENU Key

a. Menu Screen

b. Remote Support

c. Time and Date

6. Using the ADVANCED Key

a. Extended Function Screen

b. Accessing the Extended Function Screen

7. Using the LIGHT Key

8. Promo Screens

a. Informational

b. Request a Link

c. Request an Email

d. Channel Tuning

e. Channel Promo Screens

f. Browsing Promos

9. Alert Screens

Advanced Settings

1. View Device Settings

2. View DirecTune* Settings

3. Adjust DirecTune Method

4. Adjust DirecTune Speed

5. Channel Key Settings

6. Add or Clear Channel Lock

7. Add or Clear Volume Lock

Troubleshooting

1. General

2. Setting up

3. Syncing

FAQ

Specifications

License Agreement

Privacy Policy

Index

Table of Contents

40

41

42

43

44

45

46

47

49

50

51

53

55

57

59

61

62

63

65

66

69

70

3

*Trademark

Introduction

1. Evolve GUIDE Remote*

The Evolve GUIDE Remote* (GUIDE Remote*) is more than a universal remote

control—it is the ultimate interactive device for TV and Internet users. The

GUIDE Remote has state-of-the-art features that provide you and your family

with hand-held, instantaneous access to weekly TV Listings, games, viewer

rewards and valuable discounts. It allows you to request information about your

favorite programs while you watch TV, and then interact with your requested

information on your computer (PC) using the Internet.

The screen on your GUIDE Remote is always on, providing instant access to the

TV program listings, Interactivity Offers and special Promo Offers.

Please use this manual to become familiar with your remote. The GUIDE Remote

can control up to 16 devices, including TVs, VCRs, Cable settop boxes, Satellite

receivers, CD players, stereo receivers, digital tape players, phonographs and

home automation systems. In fact, the GUIDE Remote has built-in control codes

for nearly every make and model of infrared (IR) controlled device.

LCD screen

Battery coverConnector port

Speaker

IR lens

Evolve GUIDE Remote

4

*Trademark

The following system is recommended for software installation and use:

A PC running Windows 95/98, Windows ME, Windows NT Workstation

version 4.0+, Windows 2000 or Windows XP.

An Internet Explorer 5.0+, Netscape 4.0+ or AOL 5.0+ Web Browser.

(NOTE: Microsoft Internet Explorer 5.0 must be installed on your computer

even if it is not your default browser, because RemoteLinker uses resource

files provided only with Internet Explorer.)

One available RS-232 Serial Port.

A CD ROM Drive.

At least 5 MB free hard disk space.

At least 8 MB RAM.

An active connection to the Internet.

2. Computer Requirements

Introduction

Computer Requirements

5

*Trademark

3. Key Descriptions

Introduction

Key Layout

Key Descriptions

Keys shown in gray are used to navigate and control what appears on the remote

screen.

All other keys operate like those found on regular remote controls.

6

*Trademark

Introduction

Key Function Descriptions

Press this key to voice your opinion. Rate what you’re watching

with the push of a button. See what others think.

Press this key to access the three types of TV Listings: Program

Listings, Suggestions, and Reminders.

Press this key to access the Main Menu. You can configure and

setup the remote the way you like it.

Press these keys to navigate in the screen.

Press this key to choose highlighted item(s) and/or request links to

Promo Offers on the screen.

Press this key to quit the current operation.

Press this key to access the remote functions that are not

represented on the GUIDE Remote* keypad ( i.e. sleep, play, PIP,

etc.).

Press this key to save money. Find coupons, deals, and savings

related to what you’re watching.

Press this key to win big. Enter sweepstakes and contests with

incredible ease; earn points for valuable bonuses.

Press this key to buy smart. Find great stuff related to advertisers

and your favorite TV shows.

Press this key to find out more. Get more information about the

show you’re watching.

Key Descriptions

7

*Trademark

Introduction

Press this key to select which device you want the remote to

control.

Press this key to select which device you want the remote to

control.

Turns on or off the backlight on the screen.

Turns on or off the device your remote is currently controlling.

Changes channels up or down.

Adjusts volume up or down.

Turns the volume on or off.

Tunes your TV back to the previous channel watched.

Press these keys to tune to a channel on your TV.

Press this key if needed by your device after you use the digit keys

to tune to a channel.

Key Descriptions

8

*Trademark

Note A Low Battery icon appears on the top of all display screens when

the battery power is low.

Getting Started

1. Activate Remote Control

Install Batteries

The battery cover is located on the back of the remote. Pay close attention to the

direction of the batteries, making sure the poles (+ and -) are aligned as indicated in

the battery compartment.

Remove battery case cover to install the batteries in the remote control:

Press firmly on the arrow on the back of the remote to remove the battery

cover.

Insert four new 1.5-volt AA alkaline batteries, taking care to align the

poles ( + and - ) as indicated in the battery compartment.

Close the battery cover.

Note The batteries in your GUIDE Remote* should last about three months,

depending on how much you use it. If the remote will not be in use for three

or more weeks, it is suggested that you remove the batteries to avoid

damage to the remote.

Note Your remote will not lose its device settings when you remove and reinstall

batteries. However, you will need to either sync your remote or set the time

and date manually (see page 42) for your remote to work properly.

1

2

Activate Remote Control

1.5-volt AA alkaline

3

9

*Trademark

Install RemoteLinker* Software

The RemoteLinker* software is an easy-to-use utility for downloading TV Listings

and uploading your saved Interactivity Offer requests to our Website.

Getting Started

Note In step 3, you can also start the RemoteLinkerInstall.exe by selecting

START and RUN from the Taskbar. Type D:\RemoteLinkerInstall.exe

(Replace D: with the letter of your CD-ROM drive if necessary). Click OK or

press the Enter key.

Help If you are having trouble installing the RemoteLinker software, try the

following:

- Check the Readme file in the RemoteLinker program folder.

- Check and verify that your computer meets the minimum system

requirements. (see page 4)

- Temporarily turn off any PDA syncing, anti-virus or screen-saver software

on your computer.

Activate Remote Control

Note Palm Users: You should disable your Palm software before you install the

RemoteLinker* software. Additionally, if the GUIDE Remote* and Palm

share the same serial port, you are required to disable the Palm software

before you sync your remote.

1

2

3

4

5

IMPORTANT: Temporarily disable any PDA syncing and anti-virus software,

and if necessary, restart your computer.

Insert the RemoteLinker Software CD into your CD-ROM drive.

Double click on RemoteLinkerInstall.exe file in the CD-ROM.

Follow the installation instructions on the screen until finished.

Once the software is installed, when prompted, select the “Yes, I want to

launch RemoteLinker now” option.

10

*Trademark

Note If you have more than one serial port, make sure that the RemoteLinker*

software is configured to the one that you’re using. To access COM port

settings, right-click on the RemoteLinker icon located in the lower right

hand corner of your computer screen. Choose Settings. Select the correct

COM port to which you will be connecting the cable and click Apply.

Connect RemoteLinker* Cable

Before you connect the RemoteLinker* cable, you should determine the COM

port to which you will be attaching the cable. If your computer is on, perform the

shutdown procedure recommended by the manufacturer and turn it off. Turn your

computer back on after connecting the cable as indicated below.

Getting Started

Connect the small end of the cable to

the bottom of your GUIDE Remote.

Connect the large end of the cable

to the PC serial port.

Activate Remote Control

11

*Trademark

Getting Started

2. Start RemoteLinker* Software

Initiating Web Activation

1

2

Make sure you are connected to the Internet. YOU MUST BE ONLINE

Double-click the RemoteLinker* icon located in the lower right hand

corner of your computer screen, in the system tray near the system clock, to

start activating your remote. You may need to wait a few seconds for the

activation page to show up on your browser.

Note Double-clicking on the RemoteLinker* icon will take you to the Remote

Activation page at our Website. Follow the step-by-step instructions on the

Website to finish the activation process successfully.

Activating and Signing Up

When you double-clicked on the RemoteLinker icon, you started the activation and

sign-up process at www.GuideRemote.com. The instructions on the Website will

ask you to do the following:

1

2

Identify how you obtained your GUIDE Remote*.

Enter your email address, which MUST BE A VALID EMAIL ADDRESS.

Note At the end of the activation and sign-up process we will send you a

confirmation email. Click on the link in the email to complete the activation

process.

3

Enter your ZIP CODE and SERVICE TYPE.

4

Select your SERVICE PROVIDER.

5

Enter your PROFILE.

Start RemoteLinker Software / Activate Remote Control at Website

3. Activate Remote Control at Website

Note If you have problems starting the RemoteLinker software please refer to

“Syncing” on page 62.

12

*Trademark

Getting Started

6

8

Enter your PASSWORD.

Select up to 2 Critics for Suggestions.

9

REVIEW your settings. Make sure everything is correct.

10

CHECK YOUR EMAIL AND CLICK ON THE LINK TO COMPLETE THE

ACTIVATION PROCESS.

7

Select your channels. THESE ARE THE CHANNELS FOR YOUR

PROGRAM LISTINGS.

4. Sync Remote Control

Download your TV Listings (Program Listings, Program

Descriptions, Suggestions, and Reminders)

1

Connect your GUIDE Remote* to your computer, if it is not already connected.

2

Double-click on the RemoteLinker* icon located in the lower right hand

corner of your computer screen, in the system tray, to download and get your

Program Listings, Program Descriptions, Suggestions, and Reminders.

Note Prior to double-clicking on the RemoteLinker* icon to download, you must be

connected to the Internet and also logged in at our Website. Otherwise, if you’re not

logged in, your browser will be directed to the Login page at the Website. You’ll then have

to enter a username (email address) and password to log in. Double-click on the

RemoteLinker icon again to start the downloading process.

Sync Remote Control

13

*Trademark

5. Setup Remote Control

Setup a TV

Setting up your GUIDE Remote* to operate your TV is an easy process. To set up a

new a TV (or to add new ones later on), perform the following steps:

Getting Started

1

2

3

4

5

Turn on the device that you

will be setting up.

Press the MENU key to enter

the Main Menu.

Highlight Setup a Device and

press the SELECT key.

Highlight Television and

press the SELECT key.

Highlight the brand of your TV

and press the SELECT key.

If you cannot find your brand

on the list, you can choose

the brand “~UNKNOWN~”

(the last choice on the list).

Note Choosing “~UNKNOWN~” brand requires you to test all the codes in the

library. Although one of these codes may work for your device, we cannot

guarantee it.

Setup Remote Control

Tip To scroll quickly through the list, press and hold the Up or Down Arrow key.

14

*Trademark

Getting Started

6

7

8

Read and follow the

instructions on the screen.

Press the Down Arrow key

to read all the text.

Press the Right Arrow key to

continue.

To test codes, point the

remote toward the TV and

press keys like “POWER”,

“VOL”, “CHAN”, etc.

If the keys respond, highlight

Yes and press the SELECT

key, then go to step 8.

If the keys do not respond,

highlight No and press the

SELECT key. (repeat step 7

to test the next code)

Once a code is found that

operates your device, basic

setup is complete.

Press the Right Arrow key.

Setup Remote Control

Note If more than one of any type of device is setup in your remote (i.e. 2 or more

TVs or VCRs), they will be sequentially numbered (i.e. TV, TV#2, TV#3 or

VCR, VCR#2, VCR#3, etc.). The devices will appear in the order that you

set them up.

15

*Trademark

Setup Devices

Setting up your GUIDE Remote to operate additional devices such as VCR, Cable

Box, Satellite Receiver, CD Player, Audio Receiver, Amplifier and Tape, DAT,

Phonograph, DVD, Laser Disk and Home Control is an easy process.

To setup these types of devices, perform the following steps:

Getting Started

1

2

3

4

Turn on the device that you

will be setting up.

Press the MENU key to enter

the Main Menu.

Highlight Setup a Device and

press the SELECT key.

Highlight the device type you

wish to set up (i.e. TV, VCR,

Cable Box, etc.) and press

the SELECT key.

For this example, we will

setup a VCR.

Setup Remote Control

16

*Trademark

6

Read and follow the

instructions on the screen.

Press the Down Arrow key

to read all the text.

Press the Right Arrow key to

continue.

5

Highlight the brand of your

device and press the

SELECT key.

For this example, we will

setup a Panasonic VCR.

If you can not find the brand

on the list, you can choose

the brand “~UNKNOWN~”

(the last choice on the list).

Note Choosing “~UNKNOWN~” brand requires you to test all the codes in the

library. Although one of these codes may work for your device, we cannot

guarantee it.

Tip To scroll quickly through the list, press and hold the Up / Down Arrow key.

Setup Remote Control

Getting Started

17

*Trademark

Getting Started

7

To test codes, point the

remote towards the device

and press keys like

“POWER”, “VOL”, “CHAN”,

etc. Or, to access keys such

as “PLAY”, “STOP”,

“SLEEP”, etc. see the first

note below.

If the keys respond, highlight

Yes and press the SELECT

key, then go to step 8.

If the keys do not respond,

highlight No and press the

SELECT key. (repeat step 7

to test the next code)

If the keys you want to test

are not on the remote,

access the Extended

Function Screen by pressing

the ADVANCED key and

follow step 7b.

Note Most devices can be tested using the “hard” keys on the remote like

“POWER”, “VOL”, “CHAN” etc. However, depending on the device, such as

stereo receivers, CD players, digital tape players, etc., you may be required

to access the Extended Function Screen because the hard keys are not on

the remote (i.e. Play, Stop, Menu, Contrast, etc.). (see step 7b)

Setup Remote Control

Note There is a possibility that more than one code will work when setting up your

device. After you have completed setup, if you cannot find a function in

the Extended Function Screens, remove the device and try setting up the

device again using a different code.

18

*Trademark

Getting Started

7b

7c

8

Press the ADVANCED key to

access the Extended

Function Screen.

To test codes, highlight a

function from the list and

press the SELECT key. Only

functions which are also

present on your original

remote will work on your

device.

Press the Up / Down

Arrow key to access

additional functions.

When you’re finished testing,

press the Right Arrow key.

Once a code is found that

operates your device, basic

setup is complete.

Press the Right Arrow key.

7d

If the keys respond, highlight

Yes and press the SELECT

key then, go to step 8.

If the keys do not respond,

highlight No and press the

SELECT key. (repeat step 7b

to test the next code)

Note When testing functions from the list, you must pick the correct function as on

your original remote. There may be many other additional functions

on the list that do not relate to your device. If the appropriate functions

respond, you have found the right code.

Setup Remote Control

19

*Trademark

Remove a Device

You may remove a device from setup at any time. To remove a device from setup in

your GUIDE Remote, perform the following steps:

1

2

4

Press the MENU key to enter

the Main Menu.

Highlight Remove a Device

and press the SELECT key.

If you really want to remove

this device, highlight Yes and

press the SELECT key.

Getting Started

Note If you remove a DirecTune* device you will see a caution screen.

In addition, you will not be able to tune from within the TV Listings, or

access Interactivity Offers.

5

The device has been

removed.

Press the Right Arrow key.

Note If you highlight No and press the SELECT key or press the EXIT key at this

time, you will retain your current settings.

3

Highlight the device you want

to remove and press the

SELECT key.

Setup Remote Control

Page is loading ...

Evolve Communications RD5000 User manual

This manual is also suitable for

Evolve Communications RD5000 User manual

Other documents