Compaq ProLiant DL760 generation 2 Upgrade Manual

Brand: Compaq

Model: ProLiant DL760 generation 2

Category: Servers

Type: Upgrade Manual

This manual is also suitable for

DL760 - ProLiant - 1 GB RAM

Regulatory Compliance Notices

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and

identification, this product has been assigned a unique series

number. The series number can be found on the product

nameplate label, along with all required approval markings

and information. When requesting compliance information for

this product, always refer to this series number. The series

number should not be confused with the marketing name or

model number of the product.

Regulatory Notice Rating Label

The rating label on the device shows which class (A or B) the

equipment falls into. Class B devices have an FCC logo or

FCC ID on the label. Class A devices do not have an FCC ID

or logo on the label. After the class of the device is

determined, refer to the corresponding statement on the

Documentation CD.

Audience Assumptions

This poster provides a quick way for customers experienced in

server installation to upgrade the ProLiant 8500 or ProLiant

DL760 server to a ProLiant DL760 Generation 2 server. These

instructions are written assuming you are qualified to install

and service computer equipment and are trained to recognize

hazards in products with high energy levels, such as the

power supplies in this computer system. For detailed

instructions, refer to the HP ProLiant DL760 Generation 2

Server User Guide included on the Documentation CD.

hp ProLiant DL760

generation 2 server

upgrade poster

Important Safety Information

Before installing the product, read the Important Safety

Information guide included with the server.

WARNING: This product contains energy levels that are

considered hazardous. There is a risk of personal injury

from electric shock and hazardous energy. The installation

and servicing of this product must be performed by

individuals who are knowledgeable of the procedures,

precautions, and hazards associated with equipment

containing hazardous energy circuits.

WARNING: To reduce the risk of personal injury or

damage to the equipment:

• Observe local occupational health and safety

requirements and guidelines for manual

material handling.

• Obtain adequate assistance to lift and stabilize

the chassis during installation or removal. The

product will be unstable when not fastened to

the rails.

• Remove all hot-plug power supplies, removable

modules, and drives to reduce the overall weight

of the product.

WARNING: To reduce the risk of personal injury from hot

surfaces, allow the internal components to cool before

touching them.

63 - 73 kg

140 - 161 lb

WARNING: To reduce the risk of personal injury from hot

surfaces, allow the internal components to cool before

touching them.

CAUTION: To prevent damage to the system, you must

become static-free by touching a screw or unpainted

surface on the system's housing before beginning these

procedures. In addition, avoid touching any exposed

metal on the option boards or the system circuit boards.

IMPORTANT: A few server configurations may exceed the power

rating of a single power supply, resulting in a loss of power redun-

dancy for the server. Use the ProLiant DL760 G2 Power Calculator

available on the ActiveAnswers website

(activeanswers.compaq.com) to ensure that power redundancy will

be maintained for your configuration.

Thank you for purchasing the

HP ProLiant DL760 Generation 2

Server Upgrade Kit.

The HP ProLiant DL760 Generation 2 Server Upgrade Kit adds

Hot Plug RAID Memory, Intel® Xeon processors MP, and PCI-X

technology to your ProLiant 8500 or ProLiant DL760 server.

After the upgrade, the server will become a ProLiant DL760

G2 server model. A new service number will be assigned to

the server to identify the new components. This service number

will be used to identify the type of system you have and will

ensure that proper help and diagnosis is given by the HP Call

Center or service technician. You will maintain the current

system serial number. When you call for service, provide both

the original system serial, number and the upgrade service

number.

NOTE: The hardware portion of the ProLiant DL760 G2 server

upgrade will take approximately 15 minutes to an hour to complete.

Duration will vary from case to case.

1 Shipping Box Contents

Unpack the shipping boxes by following the instructions and

illustrations printed on the outside of the boxes. The shipping

boxes contain the following materials:

• HP ProLiant DL760 Generation 2 Server

Documentation CD

• HP ProLiant Essentials Foundation Pack

• ProLiant DL760 G2 front hood label

• ProLiant DL760 G2 I/O module with NC7770 PCI-X 10/

100/GB network adapter and embedded Smart Array 5i

• ProLiant DL760 G2 processor and memory module with

four Intel Xeon processors MP and 10 PC133 DIMMs.

• ProLiant DL760 G2 system midplane

• ProLiant DL760 G2 I/O lid with label

• Two ProLiant DL760 G2 service number labels

• Two 220V power cables

2 Preparing the Server

Before beginning the upgrade procedure, unpack the upgrade

kit and carefully review the procedure.

1. Back up all data on the server. The operating system,

applications, and data will need to be reinstalled after the

hardware portion of the upgrade.

Refer to the HP QuickSpecs for the ProLiant DL760 G2

server at www.hp.com/products/servers/platforms.

CAUTION: The ProLiant DL760 G2 server upgrade process

can destroy data on the server. To ensure that you do not

lose data, always back up the server before starting the

upgrade process.

2. Shut down the operating system as directed by the

operating system instructions.

3. Power down the server.

4. From the rear of server, label all the I/O expansion board

cables and expansion boards to match them later.

5. Disconnect all the cables from the rear of the server.

6. Disconnect the cable management arm from the rear of

the server.

3 Removing the Modules

The upgrade involves replacing the system midplane, the I/O

module, and the processor and memory module. Extend the

server on its rails to gain access to front and rear of the server

from the front of the rack.

To remove the processor and memory module:

1. Release the processor and memory module by pressing in

the sides of the module release levers (1) and rotating the

top of the levers downward (2). Pull the module out of the

chassis until it reaches the module stop latches (3).

2. Remove the processor and memory module from the

chassis by pressing in the module stop latches (1) and

pulling the module out of the chassis (2). The processor

and memory module will not be reused.

To remove the I/O module:

1. Release the I/O module by pressing in the sides of the

module release levers (1) and rotating the top of the levers

downward (2). Pull the module out of the chassis until it

reaches the module stop latches (3).

2. Remove the I/O module from the chassis by pressing in

the module stop latches (1) and pulling the module out of

the chassis (2). The I/O module will not be reused,

but any I/O expansion boards must be transferred

to the new I/O module.

To remove the server midplane, disengage the power supplies

and the media module. To remove the power supplies:

1. Squeeze upward on the release in the middle of the power

supply 1 handle (1).

2. Rotate the power supply handle downward (2) and slide

forward (3). Ensure power supply 1 is disengaged from

the midplane.

3. Repeat steps 1 and 2 for power supply 2.

To release the media module:

1. Press in the sides of the cam levers on the media module

(1) and rotate the tops of the levers downward (2).

2. Pull the media module out of the chassis until the module

makes contact with the module stop latches (3).

Continued on next page

4 Removing the I/O Lid

With the processor and memory module removed from the

chassis, remove the I/O lid. Grasp the sides of the I/O lid and

slide it forward until it is free of the server chassis and set

aside. The I/O lid will not be reused.

5 Replacing the System Midplane

The system midplane assembly is the board to which the server

modules and the power supplies connect.

To remove the system midplane assembly:

1. Loosen the two thumbscrews securing the system midplane

assembly to the chassis (1).

2. Remove the system midplane assembly from the chassis (2)

and set aside. The midplane assembly will not be reused.

To install the ProLiant DL760 G2 system midplane:

1. Angle the bottom edge of the midplane assembly into the

chassis (1), making sure that the edge is seated under the

chassis midplane retainers.

2. Tilt the midplane assembly vertical (2), ensuring that the

tab on the chassis engages the slot on the assembly. This

secures the midplane assembly in place.

3. Secure the midplane assembly with the two

thumbscrews (3).

6 Transferring the I/O Expansion

Boards to the New I/O Module

Before you install the new I/O module, you must transfer any

existing I/O expansion boards from your existing I/O module

to your ProLiant DL760 G2 I/O module.

Remove the I/O expansion boards from the existing

I/O module:

1. Open the air baffle (1).

2. Press on the top of the appropriate expansion slot release

lever (2) and open the lever toward the rear of the

expansion slot (3).

3. Remove the expansion board out of the server (4).

The ProLiant DL760 G2 I/O module has five PCI-X buses with

two slots each. Each slot supports PCI-X expansion boards at

100 MHz and 66 MHz, or PCI expansion boards at 66 MHz

and 33 MHz; it is keyed for 3.3V signaling. While bus

balancing is not required, you can take full advantage of all

PCI and PCI-X expansion board capabilities by putting boards

of different capabilities on different buses. Refer to the ProLiant

DL760 G2 I/O lid for PCI/PCI-X bus definitions. Slot 9 is PCI

and supports PCI expansion boards at 33 MHz; it is keyed for

5V signaling. This slot is recommended for the RILOE II

expansion board option.

NOTE: The I/O board has a Remote Management connector (30-

pin) to which the Remote Management cable (30-pin) connects. Refer

to the HP ProLiant DL760 Generation 2 Server User Guide for details

on installing the RILOE II option.

To install the I/O expansion boards in the ProLiant DL760 G2

I/O module:

1. Press the top of the I/O expansion slot release lever (1)

and open the lever toward the rear of the expansion

slot (2).

2. Remove the expansion slot cover (3).

3. Insert the I/O expansion board into the appropriate

expansion slot (1), pushing firmly until the board is

securely seated.

4. Close the expansion slot release lever at the rear of the

module to secure the board (2). Be sure that the lever

latches into the closed position.

5. Add any additional option expansion boards, as desired.

HP has designed a self-latching slot-keeper feature to

accommodate full-length expansion boards.

Be sure that the V-shaped slot-keeper tabs on the plastic

expansion board guide are positioned over the forward end of

the expansion board.

7 Reassembling the Server

Reassemble the server with all the new ProLiant DL760

G2 components.

1. Install the ProLiant DL760 G2 I/O module into the

server chassis.

2. Reseat the media module into the chassis.

3. Reseat the two power supplies:

a. Slide power supply 1 into the power supply cage until

the supply is seated securely (1). This action automati-

cally pushes the spring-loaded trap door open.

b. Raise the handle to lock the power supply into place

(2). The power supply fan starts immediately if the

system is running.

c. Repeat steps a and b for the second power supply.

4. Install the new I/O lid by sliding it into the front of the

server. The hood label is oriented to be read from the front

of the server.

5. Install a processor board option kit into the ProLiant DL760

G2 processor and memory module if an eight-processor

configuration is desired. Refer to the documentation

provided with the processor board option.

6. Install any additional memory into the five memory

cartridges located at the front of the ProLiant DL760 G2

processor and memory module. Refer to the memory

requirements and installation procedures in the HP

ProLiant DL760 Generation 2 Server User Guide located

on the Documentation CD in the upgrade kit.

7. Install the ProLiant DL760 G2 processor and memory

module into the server chassis.

WARNING: The processor and memory module weighs

more than 15.9 kg (35 lb). HP recommends either

removing ALL the memory cartridges before handling the

module, or having two people handling the module

together.

8 Installing the Server Labels

Install the ProLiant DL760 G2 specific labels.

1. Install the front hood label (accessing module and memory

information). Align the corners of the label and carefully

lower it over the existing front label on your server.

2. Install the front service number label (1) next to the existing

server serial number (2) on the front top edge of the

server.

Continued on next page

3. Install the rear service number label (1) next to the existing

server serial number (2) on the left rear edge of the server.

These service numbers will be used to identify the type of

system you have and will be sure that proper help and

diagnosis is given by the HP Call Center or service technician.

The service number labels should be referenced when

calling for service.

IMPORTANT: Do not superimpose the service number label over the

serial number labels. The service number labels are needed for

warranty purposes.

9 Completing the Upgrade

1. Slide the server back into the rack.

2. From the rear of the rack, attach the cable management

arm to the server.

3. Reinstall all I/O cables and power cables. Verify the

power supply (AC) LED is solid green.

IMPORTANT: ProLiant DL760 G2 server configurations require 220V

power. Install the 220V power cables that came with your server, if

not already in use (two 220V power cables are available in the

upgrade kit).

4. From the front of the server, verify that the interconnect

check light is not lit. This ensures all critical components

are properly seated in the server.

5. Power up the server.

6. Run system diagnostics.

7. Configure the server, using RBSU.

8. Reinstall the operating system.

9. Reinstall the applications.

10. Restore the data.

11. Register the new system configuration with HP for proper

service response.

12. Discard or redeploy remaining parts.

Memory Considerations

The upgrade kit comes standard with 10 PC133 SDRAM

DIMMs. The upgraded server can support either PC100 or

PC133 memory. In addition, both PC100 and PC133 memory

can be installed in the system at the same time, as long as the

memory is installed in different bank pairs. With any PC100

memory in the system, the memory subsystem will run at

100 MHz.

Eight or ten DIMMs are required to fill bank pairs, as

indicated by socket numbers 1&2, 3&4, 5&6, 7&8, and must

be installed in numerical bank order.

To install PC100 memory in the system, use one of the

following DIMMs.

yromeM001CPdetroppuS:1elbaT

traPPH

rebmuN

-859011

230

-959011

230/130

-959011

240/140

-549511

240/140

eludoM

ytisneD

BM652BM215BM215BG1

forebmuN

nosMARD

eludom

81638163

.hceTMARDS

desU

BM821BM821BM652BM652

forebmuN

repsknaB

eciveDMARDS

4444

rebmuN

sknaBlacisyhP

eludoMno

1212

lacisyhP

eludoM

noitazinagrO

27xM2327xM23x227xM4627xM46x2

eludoM

fonoitceleS

MARDS

gniknaB

1AB-0AB1AB-0AB1AB-0AB1AB-0AB

gnisserddA

)loC/woR#(

11/2111/2111/31

11/31

sserddAwoR

seniL

11A-0A11A-0A21A-0A21A-0A

nmuloC

seniLsserddA

,9A-0A

11A

,9A-0A

11A

,9A-0A

11A

,9A-0A

11A

eciveDesaB

desU

4xM234xM234xM464xM46

yromeM331CPdetroppuS:2elbaT

traPPH

rebmuN

-500721

130

-600721

140

-800721

140

-117192

150

eludoM

ytisneD

BM652BM215BG1BG2

forebmuN

nosMARDS

eludoM

81816363

.hceTMARDS

desU

BM821BM652BM652BM215

sknaBrebmuN

MARDSrep

eciveD

4444

rebmuN

sknaBlacisyhP

eludoMno

1122

lacisyhP

eludoM

noitazinagrO

27xM2327xM4627xM46x2

821x2

27xM

gnisserddA

)loC/woR#(

11/2111/3111/3121/31

sserddAwoR

seniL

11A-0A21A-0A21A-0A21A-0A

nmuloC

seniLsserddA

,9A-0A

11A

,9A-0A

11A

,9A-0A

11A

,9A-0A

21A-11A

eciveDesaB

desU

4xM234xM464xM464xM821

The following PC133 memory can be installed.

For memory requirements, review the memory requirements

section of the HP ProLiant DL760 Generation 2 Server User

Guide located on the Documentation CD in the upgrade kit.

To install PC100 or PC133 memory in the system, the DIMMs

must be installed in increments of 10 (or eight, if a redundant

array of memory is not desired) and be of the same size, type,

and speed. DIMM similarity can be confirmed by common

DIMM part numbers. For HP part number nomenclature, the

following example shows that the first eight numbers of the

nine digit part number must match: 123456-78x

Additional Resources

For additional information on the topics covered in this guide,

refer to the following documentation available on the

Documentation CD:

• HP ProLiant DL760 Generation 2 Server User Guide

• Smart Array 5i Controller User Guide

• ROM-Based Setup Utility User Guide

• Servers Troubleshooting Guide

• PCI Hot Plug Administration Guide

• Remote Insight Lights-Out Edition II User Guide

For the HP ProLiant DL760 G2 Power Calculator, refer to the

ActiveAnswers website at

activeanswers.compaq.com

Legal Notices

Intel® and Pentium® are trademarks of Intel Corporation in the U.S. and other countries.

Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions

contained herein. The information in this document is provided "as is" without warranty of

any kind and is subject to change without notice. The warranties for HP products are set

forth in the express limited warranty statements accompanying such products. Nothing

herein should be construed as constituting an additional warranty.

First Edition (March 2003)

Part Number 323574-001

Compaq ProLiant DL760 generation 2 Upgrade Manual

Brand: Compaq

Model: ProLiant DL760 generation 2

Category: Servers

Type: Upgrade Manual

This manual is also suitable for

DL760 - ProLiant - 1 GB RAM

Download PDF

report

Compaq ProLiant DL760 generation 2 Upgrade Manual

This manual is also suitable for

Compaq ProLiant DL760 generation 2 Upgrade Manual

Related papers

Other documents