VintageView W Series Wine Rack Frame Angled Base Plate Installation guide

Brand
VintageView
Model
W Series Wine Rack Frame Angled Base Plate
Type
Installation guide
W Series Wine Rack Frame with Angle Baseplates
Installation guide for the standard W Series Frame with FCF-ANGLE
Included:
• (2) Angle Base Plates
• (2) Self-drilling Screws
Important Note:
These installation instructions will assist you with installing the VintageView W Series Frame System (10’, 12’, or
magnum bottle congurations) with Angle Baseplates into an angled surface, up to 35 degrees.
Fasteners:
Fasteners for securing W Series racking to the Frame is included, but hardware for oor or ceiling surfaces is
not. When installing nished W Series Frame to the oor or ceiling, please use the following recommendations
for fasteners:
Additional Components:
(sold separately unless purchasing
complete kit)
• W Series Wine Racks
• W Series Frame (HD, 12, Mag
models)
• W Series Frame Backer Bar
(single-sided displays)
Required Tools:
• Drill
• Phillips head drill bit
• Phillips head screwdriver
• Level
• Pencil or Marker
• Tape measure
• Metal cutting saw
• Metal le
Instructions: W Series Wine Rack Frame with Angle Base Plates
Figure A
Figure B
NOTE: The W Series Wine Rack Frame can be installed
with Angled Base Plates either Parallel to the angle (one
side of Frame lower than the other) or Perpendicular to it.
1. IDENTIFY PROPER HARDWARE
Using the chart on the previous page, identify the proper
oor/ceiling hardware (not included) that will be needed
for your specic project. For drywall surfaces, Vinta-
geView recommends installing to joists or wood backing
when available.
2. MEASURE CEILING HEIGHT
Measure the desired location’s ceiling height at the tallest
point (outside of Frame for perpendicular installs or front
of frame for parallel installs).
If installing Frame perpendicular to the angled corner,
also measure down the surface 8.5in (216mm) to obtain
the height at the lowest point for the opposite side of the
Frame (Figure A).
** Magnum Frame adjustment **
Measure 9.5in (242mm) from the height at the tallest
point to capture the height at the lowest connection point.
3. MEASURE THE CEILING ANGLE
Measure the ceiling angle using an Adjustable Square
(Figure B).
4. INSERT COUPLERS
Insert two (2) Frame Couplers to the section of the Frame
that will be used for the Bottom (Figure C).
** 12’ Frame Adjustment **
W Series Frame 12’ comes with welded c-channels. Con-
nect the Middle Frame to the bottom Frame be rmly slid-
ing the welded c-channel of the Middle into the bottom.
5. MARK CUT LINES
Lay each section, interlaced, as show (Figure D).
Position the Frame so that the measurement from the
Top Section (open end) to its bottom section (Mount-
ing Plate) equals your ceiling measurement.
Figure C
Figure D
Instructions: W Series Wine Rack Frame with Angle Base Plates
The ceiling Mounting Bracket should be on the over-
lapped side for the measuring and cutting purposes.
For Parallel installations:
Use a Pencil to the front, higher side of the top section
of the Frame (Featuring the hollowed opening) on both
sides where it overlaps the bottom section of the Frame
(Figure E).
Using the Adjustable Square, draw your cut line at the
desired angle from the marks (Figure G).
For Perpendicular Installations:
Use a Pencil to mark the higher side of the top section of
Frame (featuring the hollowed opening) where it overlaps
the bottom section of Frame. This mark should be made
on the outside of the Frame (Figure F).
Adjust the overlap of the two Frames to equals the lower
ceiling height measurement.
Use a pencil to mark the opposite side of the top section
of Frame. The mark should be made on the outside of the
Frame.
Using the Adjustable Square, draw your cut line at the
desired angle from the marks (Figure H). Mark the angle
down from the highest mark and up from the lowest
measurement.
If the cut mark aligns with a cross member, measure and
cut 2in (51mm) off the bottom Section using a Metal
Cutting Saw and start the step over (Figure I).
** 12’ Frame Adjustment **
Do not cut from the center section.
6. CUT THE FRAME
Using a Metal Cutting Saw, cut the marks at the angle on
the Top Frame section (Figure J). Smooth the end of
the Frame with a Metal File.
Do not use abrasive saws as they may damage the
finish.
Figure H
Figure I
Figure J
Figure F
Figure E
Figure G
Instructions: W Series Wine Rack Frame with Angle Base Plates
7. CONNECT THE FRAME
Connect the top Section to the Bottom, ensuring the
Couplers are rmly lodged into both ends of the Frame
(Figure K).
** 12’ Frame Adjustment **
Connect the top Section to the connected Middle/Bottom
section.
8. INSERT ANGLE BASE PLATES
Insert (2) Angle Base Plates into the top Frame (Figure L).
When inserting, position so the Tube of the Angled Base
Plate goes into the lower side of the Frame. The Angled
Base Plate will t square in the Post when installed.
Secure the Angles with provided Self-Drilling Screws,
ensuring the drill hole goes through the tube (Figure B).
9. BUILD THE RACKS
It is common to use one (1), two (2), or (3) W Series
Wine Racks on one or both sides of a W Series Frame. If
using more than one, connect the W Series Wine Rack-
ing by removing the two (2) Endcaps from the end of
each Wine Rack where they will connect.
Connect the Neck Strips (smaller bottle impressions) to-
gether with the supplied Wine Rack Couplers (Figure M).
Repeat with the Base Strips (larger bottle impressions).
VintageView recommends leaving a minimum of 6in
(153mm) above and below the W Series Racks when
assembled to Frame.
10. PLACE THE RACKS
Lay the connected Strips in the desired location on the
Frame, ensuring the Neck Strips are facing in preferred
direction. IMPORTANT: One single Wine Rack Strip must
extend 12in (305mm) above or below all connection
points of the Frame (Figure N).
Figure M
Figure N
Figure LFigure K
Instructions: W Series Wine Rack Frame with Angle Base Plates
11. SECURE THE RACKS
Attach the Racking Assembly to the Frame (Figure O)
using two (2) or three (3) Self Drilling Screws per Strip
(quantity will vary based on individual height of racking).
Then press two (2) or three (3) Mounting Hole Covers
into each Strip section (quantity will vary based on indi-
vidual height of racking).
12. SUPPORT THE BACK
All connection points on the backside of the Frame must
be supported by either Wine Racking or a W Series
Frame Backer Bar.
For Single Sided Displays
Use eight (8) Self-Drilling Screws to attach two (2) W
Series Frame Backer Bars (FCF-BACK) to the back side of
the Frame, centered over the two connection points. Then
press eight (8) Mounting Hole Covers over the Screws
(Figure P).
** 12’ Frame Adjustment **
The 12’ frame features four connection points and re-
quires four (4) Backer Bars.
For Double-Sided Displays
Repeat Steps 8-10 to install Wine Racks to the back side
of the Frame (Figure Q).
IMPORTANT: The Backer Bar or Wine Racking must ex-
tend 12in (305mm) above or below all connection points
of the Frame.
13. MARK CEILING/
FLOOR MOUNTING HOLES
Place the Frame in desired location. Ensure it is plumb
with a level and mark the mounting holes on both the
ceiling and the oor. Set the Frame aside and pre-drill
any required pilot holes based on hardware selection.
Figure Q
Figure O Figure P
14. INSTALL THE SYSTEM
Stand the Frame Assembly in the desired location
and ensure it is plumb both front and back and side-
to-side with a level (Figure R).
Figure R
Instructions: W Series Wine Rack Frame with Angle Base Plates
Secure the Frame to the ceiling (Figure s) using two (2)
of the appropriate fasteners (not provided) into each
Angle Base Plate. Double check the Frame is plumb and
secure the Frame to the oor using two (2) of the appro-
priate fasteners (not provided).
15. ADD WINE
Only the good stuff.
Problems?
Try BILT 3D intelligent instructions, visit
www.vintageview.com, or call 303-504-9463.
Maintenance and Care:
The W Series Frame should be regularly checked for
tightness. Should any rack be found to be loose, tighten
by hand until secure.
W Series steel wine racks are easy to clean. Simply wipe
with a dry cloth or use rubbing alcohol. Here are more
Dos and Don’ts….
Use
• A dry dusting cloth
• Compressed air cans
• Rubbing alcohol and a clean cloth to remove grease,
oil, or other substances
Figure S
Don’t use:
• Dish soap
• Household cleaners
• Abrasive materials
• Any chemical
Improper care may void
the manufacturer’s warran-
ty.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VintageView W Series Wine Rack Frame Angled Base Plate Installation guide

Brand
VintageView
Model
W Series Wine Rack Frame Angled Base Plate
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents