Krone Messages - Parameters Operating instructions

Messages - Parameters
Krone
Brand
Krone
Model
Messages - Parameters
Type
Operating instructions

This manual is also suitable for

Krone Messages - Parameters, the device you just purchased, allows you to conveniently access and manage error messages and information messages related to your Krone machine. With its user-friendly interface, you can easily navigate through various error and information codes, getting clear descriptions and potential causes for each one. Whether you're a seasoned professional or new to Krone machinery, this device is designed to assist you in troubleshooting and maintaining your equipment efficiently.

Krone Messages - Parameters, the device you just purchased, allows you to conveniently access and manage error messages and information messages related to your Krone machine. With its user-friendly interface, you can easily navigate through various error and information codes, getting clear descriptions and potential causes for each one. Whether you're a seasoned professional or new to Krone machinery, this device is designed to assist you in troubleshooting and maintaining your equipment efficiently.

Enclose this document with the operating instructions of the
machine.
Supplement to operating
instructions
Document number: 150001730_00_us
Version: 01/08/2021
Loading and Forage Transport Wagon
Software version: D2515020092600016
Error messages and information messages
Table of contents
2
Loading and Forage Transport Wagon
Supplement to operating instructions 150001730_00_en
1 Information on this document .................................................................................................. 3
1.1 Validity ......................................................................................................................................... 3
1.2 Re-ordering.................................................................................................................................. 3
1.3 Applicable documents.................................................................................................................. 3
2 Safety .......................................................................................................................................... 4
2.1 Meaning of the supplement to the operating instructions ............................................................ 4
3 Error messages.......................................................................................................................... 5
3.1 Possible error types (FMI)............................................................................................................ 6
3.2 Error list........................................................................................................................................ 6
4 Information messages............................................................................................................. 25
4.1 Information list............................................................................................................................ 25
5 Index.......................................................................................................................................... 28
Information on this document 1
Validity 1.1
Loading and Forage Transport Wagon
Supplement to operating instructions 150001730_00_en 3
1 Information on this document
1.1 Validity
This document is valid for:
MX 400 GL MX 370 GD
MX 370 GL MX 330 GD
RX 430 GL RX 400 GD
RX 400 GL RX 360 GD
RX 360 GL TT405-31 (ZX 560 GD)
TT405-30 (ZX 560 GL) TT405-21 (ZX 470 GD)
MX 330 GL TT405-20 (ZX 470 GL)
TT405-11 (ZX 430 GD) TT405-10 (ZX 430 GL)
1.2 Re-ordering
You can request a replacement document if this document became completely or partly
unusable, or if you need it in a different language. Please specify the document number shown
on the cover page in your order. Alternatively, you can download the document online from
KRONE MEDIA https://media.mykrone.green.
1.3 Applicable documents
To ensure that the machine is used safely and as intended, observe the following further
applicable documents.
• Operating instructions of the respective machine
2 Safety
2.1 Meaning of the supplement to the operating instructions
4
Loading and Forage Transport Wagon
Supplement to operating instructions 150001730_00_en
2 Safety
WARNING
Risk of injury due to non-observance of relevant safety instructions
If the relevant safety instructions are not observed, persons may be seriously injured or killed.
In order to avoid accidents, the relevant safety instructions in the operating instructions
must be read and observed.
WARNING
Risk of injury due to non-observance of safety routines
If the relevant safety routines are not observed, persons may be seriously injured or killed.
In order to avoid accidents, the safety routines in the operating instructions must be read
and observed.
INFO
Depending on the machine type, the basic safety instructions can be found in the chapter
“Safety”, “Basic Safety Instructions” or in the chapter “Safety” of the machine operating
instructions.
2.1 Meaning of the supplement to the operating instructions
The supplement to the operating instructions is an important document and a part of the
machine. It is aimed at the user and contains safety-relevant information.
If the supplement to the operating instructions is not observed, people may be seriously injured
or killed.
Read in full and observe the “Safety” chapter of the corresponding operating instructions
before using the machine for the first time,see Page3.
Before working, also read and observe the respective sections of the corresponding
operating instructions,see Page3.
Keep the supplement to the operating instructions ready to hand for the user of the machine.
Hand over the supplement to the operating instructions to subsequent users.
Error messages 3
Loading and Forage Transport Wagon
Supplement to operating instructions 150001730_00_en 5
3 Error messages
WARNING
Risk of injury to persons and damage to machines if error messages are ignored
If error messages are ignored and the fault is not rectified, there is a risk of injury to persons
and/or severe damage to the machine.
Eliminate the disturbance when an error message is displayed, see Page6.
If the fault cannot be rectified, contact KRONE service partner.
CAN1
KMC - 520192- 19
EQG000-034
The display shows an error message when a disturbance occurs on the machine. At the same
time, an audible signal sounds (continuous horn signal). For a list of the error messages, see
Page6.
Configuration of an error message
The error message is configured according to the following sample: e.g. error message
"520192-19
CAN1
"
520192 19
CAN1
SPN (Suspect Parameter
Number) = error number
FMI = type of error, see
Page6
Icon
Acknowledging error message
Note down the error message.
Briefly press on .
ÆThe acoustic signal stops and the error display is no longer indicated. If the fault occurs
again, the error message will be displayed again.
Rectify the error, see Page6.
Acknowledged and still pending error messages can be displayed again via the "Error list" menu
or the status line.
The following key functions can be selected:
3 Error messages
3.1 Possible error types (FMI)
6
Loading and Forage Transport Wagon
Supplement to operating instructions 150001730_00_en
Icon Designation Explanation
Acknowledging error mes-
sage
If the fault occurs again, the error message
will be displayed again.
3.1 Possible error types (FMI)
There are different types of errors which are shown under the term FMI (Failure Mode
Identification) with an appropriate code.
FMI Meaning
0 The upper limit value was greatly exceeded.
1 The lower limit value was far below the required one.
2 The data is not permitted.
3 There is an overvoltage or a short circuit to supply voltage.
4 There is an undervoltage or a short circuit to ground.
5 A cable is broken or amperage is too low.
6 There is a short circuit to ground or amperage is too low.
7 The mechanics do not respond or the expected result was not achieved.
8 The frequency is not permitted.
9 There is an abnormal update rate.
10 There is an abnormal rate of change.
11 The error cause is unknown.
12 There is an internal error.
13 The values of the calibration are outside the value range.
14 Particular instructions are required.
15 The upper limit value has been reached.
16 The upper limit value has been exceeded.
17 The lower limit value has been reached.
18 The lower limit value has not been reached.
19 There is a CAN communication failure.
20 The data deviates upwards.
21 The data deviates downwards.
31 The condition has been fulfilled.
3.2 Error list
>>>
2en_Fehlerliste [}7]
Error list
Software version: D2515020141600016_300
Control unit: KMC
Page 1
Error number Error text Description Figure
KMC-520192-19 CAN1 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 1.
KMC-520193-19 CAN2 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 2.
KMC-520194-19 CAN3 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 3.
KMC-520195-19 CAN4 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 4.
KMC-520198-12 Control unit - Internal Error An internal error in the control unit
which was actuated by defective
software or hardware.
KMC-520232-12 Vehicle Identification Number -
Internal Error
The vehicle identification number has
not been initialised.
KMC-520234-31 System check with KMC failed With the KMC the cross-controller
adjustment of system-relevant
machine data has failed.
KMC-521100-3 Voltage group UB1 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521100-4 Voltage group UB1 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521100-5 Voltage group UB1 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521100-6 Voltage group UB1 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521101-3 Voltage group UB2 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521101-4 Voltage group UB2 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521101-5 Voltage group UB2 - Ground fault The maximum load on the supply
voltage has been exceeded.
KMC-521101-6 Voltage group UB2 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521102-3 Voltage group UB3 - Overvoltage The input voltage of the corresponding
voltage group is too high.
Page 2
Error number Error text Description Figure
KMC-521102-4 Voltage group UB3 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521102-5 Voltage group UB3 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521102-6 Voltage group UB3 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521103-3 Voltage group UB4 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521103-4 Voltage group UB4 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521103-5 Voltage group UB4 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521103-6 Voltage group UB4 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521104-3 Voltage group UB5 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521104-4 Voltage group UB5 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521104-5 Voltage group UB5 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521104-6 Voltage group UB5 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521105-3 Voltage group UB6 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521105-4 Voltage group UB6 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521105-5 Voltage group UB6 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521105-6 Voltage group UB6 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521106-11 Supply voltage sensors - General
disturbance
The voltage has been switched off due
to an overload or a short circuit on the
supply voltage of the sensors.
Page 3
Error number Error text Description Figure
KMC-521107-3 Supply voltage - Overvoltage The power supply on the UE
connection is too high.
KMC-521107-4 Supply voltage - Undervoltage The power supply on the UE
connection is too low.
KMC-521108-11 Control unit - General disturbance The voltage group relay UB1 has not
passed the self-test.
KMC-521109-11 Control unit - General disturbance The voltage group relay UB2 has not
passed the self-test.
KMC-521110-11 Control unit - General disturbance The voltage group relay UB3 has not
passed the self-test.
KMC-521111-11 Control unit - General disturbance The voltage group relay UB4 has not
passed the self-test.
KMC-521112-11 Control unit - General disturbance The voltage group relay UB5 has not
passed the self-test.
KMC-521113-11 Control unit - General disturbance The voltage group relay UB6 has not
passed the self-test.
KMC-521114-11 Sensor supply voltage U1 - General
disturbance
The voltage group Uext1 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521115-11 Sensor supply voltage U2 - General
disturbance
The voltage group Uext2 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521116-11 Sensor supply voltage U3 - General
disturbance
The voltage group Uext3 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521117-11 Sensor supply voltage U4 - General
disturbance
The voltage group Uext4 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521118-11 Voltage group relay UB2 - General
disturbance
Platform fault for BiG X only: A
disturbance was detected at the
intake/header (broken cable/short
circuit to one of the valves Q55 - Q58
or a broken cable/short circuit from
relay Q72). The voltage group relay
UB2 was therefore switched off.
KMC-521320-2 Machine configuration - Logic error
electronics
Configuration of the machine is not
compatible with the hardware.
KMC-521350-11 Control unit - General disturbance
Page 4
Error number Error text Description Figure
KMC-521351-11 Control unit - General disturbance
KMC-522002-18 Rotational speed of discharge rollers
- Lower limit value below minimum
The rotational speed of the discharge
rollers is too low.
KMC-522004-16 steering axle - Upper limit value
exceeded
The steering axle could not be locked
within the specified time.
KMC-522012-2 Rotational speed of PTO shaft - Logic
error electronics
The sensor "rotational speed PTO
shaft" has not been correctly set or is
defective.
KMC-522014-7 tailgate - Logic fault mechanics The tailgate is open.
KMC-522018-16 tailgate - Upper limit value exceeded The tailgate could not be closed within
the specified time.
KMC-522023-16 front wall - Upper limit value
exceeded
The front wall does not move.
KMC-522026-7 pick-up - Logic fault mechanics The pick-up has stopped.
KMC-522028-18 central lubrication unit - Lower limit
value below minimum
During active lubrication no lubrication
flow was detected.
KMC-522029-16 Grinding device - Upper limit value
exceeded
The grinding device stops when
approaching the grinding position.
KMC-522030-16 Grinding device - Upper limit value
exceeded
The grinding device stops when
grinding.
KMC-522031-7 forced steering - Logic fault
mechanics
The forced steering is not supplied with
pressure.
KMC-522034-2 forced steering - Logic error
electronics
The speed difference between the left
and right wheel sensor is not plausible.
KMC-522039-16 lift axle - Upper limit value exceeded The lift axle could not be lifted within
the specified time.
KMC-522040-16 articulated drawbar - Upper limit value
exceeded
The articulated drawbar does not
move.
KMC-522041-16 pick-up - Upper limit value exceeded The pick-up could not be lifted within
the specified time.
Page 5
Error number Error text Description Figure
KMC-522042-7 tailgate - Logic fault mechanics The tailgate unexpectedly left the open
position.
KMC-522043-7 Loading space cover - Logic fault
mechanics
The loading space cover moves
unexpectedly.
KMC-522101-3 Sensor B1 position blade cassette -
Cable break
KMC-522101-4 Sensor B1 position blade cassette -
Short circuit to ground or UB
KMC-522102-3 Sensor B2 Loading height at front
reached - Cable break
KMC-522102-4 Sensor B2 Loading height at front
reached - Short circuit to ground or
UB
KMC-522103-3 Sensor B3 Wagon completely filled -
Cable break
KMC-522103-4 Sensor B3 Wagon completely filled -
Short circuit to ground or UB
KMC-522104-3 Sensor B4 Rotational speed of
discharge rollers - Cable break
KMC-522104-4 Sensor B4 Rotational speed of
discharge rollers - Short circuit to
ground or UB
KMC-522105-3 Sensor B5 Rotational speed of PTO
shaft - Cable break
KMC-522105-4 Sensor B5 Rotational speed of PTO
shaft - Short circuit to ground or UB
KMC-522106-3 Sensor B6 Tailgate closed - Cable
break
KMC-522106-4 Sensor B6 Tailgate closed - Short
circuit to ground or UB
KMC-522107-3 Sensor B7 Steering axle locked -
Cable break
KMC-522107-4 Sensor B7 Steering axle locked -
Short circuit to ground or UB
Page 6
Error number Error text Description Figure
KMC-522108-3 Sensor B8 Tailgate open - Cable
break
KMC-522108-4 Sensor B8 Tailgate open - Short
circuit to ground or UB
KMC-522110-3 Sensor B10 Lift axle top - Cable
break
KMC-522110-4 Sensor B10 Lift axle top - Short
circuit to ground or UB
KMC-522120-3 Sensor B20 Oil pressure scraper
conveyor - Short circuit to UB
KMC-522120-4 Sensor B20 Oil pressure scraper
conveyor - Cable break or short
circuit to ground
KMC-522124-3 Sensor B24 Filling pick-up
accumulator - Short circuit to UB
KMC-522124-4 Sensor B24 Filling pick-up
accumulator - Cable break or short
circuit to ground
KMC-522125-3 Sensor B25 Pick-up top - Cable
break
KMC-522125-4 Sensor B25 Pick-up top - Short
circuit to ground or UB
KMC-522126-3 Sensor B26 Rotational speed of pick-
up - Cable break
KMC-522126-4 Sensor B26 Rotational speed of pick-
up - Short circuit to ground or UB
KMC-522128-3 Sensor B28 Inclination angle
articulated drawbar - Short circuit to
UB
KMC-522128-4 Sensor B28 Inclination angle
articulated drawbar - Cable break or
short circuit to ground
KMC-522129-3 Sensor B29 Working angle pick-up -
Short circuit to UB
KMC-522129-4 Sensor B29 Working angle pick-up -
Cable break or short circuit to ground
Page 7
Error number Error text Description Figure
KMC-522132-3 Sensor B32 Grinding device swivelled
in - Cable break
KMC-522132-4 Sensor B32 Grinding device swivelled
in - Short circuit to ground or UB
KMC-522135-3 Sensor B35 Position loading area
cover on left - Cable break
KMC-522135-4 Sensor B35 Position loading area
cover on left - Short circuit to ground
or UB
KMC-522136-3 Sensor B36 Position loading area
cover on right - Cable break
KMC-522136-4 Sensor B36 Position loading area
cover on right - Short circuit to
ground or UB
KMC-522137-3 Sensor B37 Front wall at front -
Cable break
KMC-522137-4 Sensor B37 Front wall at front - Short
circuit to ground or UB
KMC-522138-3 Sensor B38 Inclination angle front
wall - Short circuit to UB
KMC-522138-4 Sensor B38 Inclination angle front
wall - Cable break or short circuit to
ground
KMC-522139-3 Sensor B39 Central lubrication active
- Cable break
KMC-522139-4 Sensor B39 Central lubrication active
- Short circuit to ground or UB
KMC-522150-4 Switch/momentary switch S51
System pressure steering - Cable
break or short circuit to ground
KMC-522151-4 Sensor B51 Steering angle tractor/
drawbar - Cable break or short circuit
to ground
KMC-522152-4 Sensor B52 Steering angle rear axle
- Cable break or short circuit to
ground
KMC-522153-3 Sensor B53 Driving speed left - Cable
break
Page 8
Error number Error text Description Figure
KMC-522154-3 Sensor B54 Driving speed right -
Cable break
KMC-522155-4 Sensor B55 Steering angle front axle
- Cable break or short circuit to
ground
KMC-522171-3 Sensor BM1 Distance grinding discs
to blades - Short circuit to UB
KMC-522171-4 Sensor BM1 Distance grinding discs
to blades - Cable break or short
circuit to ground
KMC-522172-3 Sensor BM2 Position grinding discs -
Short circuit to UB
KMC-522172-4 Sensor BM2 Position grinding discs -
Cable break or short circuit to ground
KMC-522177-3 Sensor B7 Steering axle locked -
Short circuit to UB
KMC-522177-4 Sensor B7 Steering axle locked -
Cable break or short circuit to ground
KMC-522201-16 Sensor B15 Force measurement
front wall - Upper limit value
exceeded
KMC-522201-18 Sensor B15 Force measurement
front wall - Lower limit value below
minimum
KMC-522203-16 Sensor B11 Weight measurement
drawbar - Upper limit value exceeded
KMC-522203-18 Sensor B11 Weight measurement
drawbar - Lower limit value below
minimum
KMC-522204-16 Sensor
- B12L Weight measurement axle left
- B12R Weight measurement axle
right
- Upper limit value exceeded
KMC-522204-18 Sensor
- B12L Weight measurement axle left
- B12R Weight measurement axle
right
- Lower limit value below minimum
KMC-522251-3 Switch/momentary switch S1 Swivel
in blade cassette - Cable break
Page 9
Error number Error text Description Figure
KMC-522251-4 Switch/momentary switch S1 Swivel
in blade cassette - Short circuit to
ground or UB
KMC-522251-7 Switch/momentary switch S1 Swivel
in blade cassette - Logic fault
mechanics
Button clamp
KMC-522252-3 Switch/momentary switch S2 Swivel
out blade cassette - Cable break
KMC-522252-4 Switch/momentary switch S2 Swivel
out blade cassette - Short circuit to
ground or UB
KMC-522252-7 Switch/momentary switch S2 Swivel
out blade cassette - Logic fault
mechanics
Button clamp
KMC-522253-3 Switch/momentary switch S3 Lift
articulated drawbar - Cable break
KMC-522253-4 Switch/momentary switch S3 Lift
articulated drawbar - Short circuit to
ground or UB
KMC-522253-7 Switch/momentary switch S3 Lift
articulated drawbar - Logic fault
mechanics
Button clamp
KMC-522254-3 Switch/momentary switch S4 Lower
articulated drawbar - Cable break
KMC-522254-4 Switch/momentary switch S4 Lower
articulated drawbar - Short circuit to
ground or UB
KMC-522254-7 Switch/momentary switch S4 Lower
articulated drawbar - Logic fault
mechanics
Button clamp
KMC-522255-3 Switch/momentary switch S5
Grinding device ON - Cable break
KMC-522255-4 Switch/momentary switch S5
Grinding device ON - Short circuit to
ground or UB
KMC-522255-7 Switch/momentary switch S5
Grinding device ON - Logic fault
mechanics
Button clamp
KMC-522301-3 Valve K1 Scraper conveyor forwards -
Cable break or short circuit to UB
KMC-522301-6 Valve K1 Scraper conveyor forwards -
Short circuit to ground
Page 10
Error number Error text Description Figure
KMC-522302-3 Valve Q2 Scraper conveyor
backwards - Cable break or short
circuit to UB
KMC-522302-6 Valve Q2 Scraper conveyor
backwards - Short circuit to ground
KMC-522303-3 Valve Q3 Pilot valve 1 - Cable break
or short circuit to UB
KMC-522303-6 Valve Q3 Pilot valve 1 - Short circuit
to ground
KMC-522304-3 Valve Q4 Pilot valve 2 - Cable break
or short circuit to UB
KMC-522304-6 Valve Q4 Pilot valve 2 - Short circuit
to ground
KMC-522305-3 Valve Q5 Pick-up 1 - Cable break or
short circuit to UB
KMC-522305-6 Valve Q5 Pick-up 1 - Short circuit to
ground
KMC-522306-3 Valve Q6 Tailgate 1 - Cable break or
short circuit to UB
KMC-522306-6 Valve Q6 Tailgate 1 - Short circuit to
ground
KMC-522307-3 Valve Q7 Tailgate 2 - Cable break or
short circuit to UB
KMC-522307-6 Valve Q7 Tailgate 2 - Short circuit to
ground
KMC-522308-3 Valve Q8 Articulated drawbar 1 -
Cable break or short circuit to UB
KMC-522308-6 Valve Q8 Articulated drawbar 1 -
Short circuit to ground
KMC-522309-3 Valve Q9 Articulated drawbar 2 -
Cable break or short circuit to UB
KMC-522309-6 Valve Q9 Articulated drawbar 2 -
Short circuit to ground
Page 11
Error number Error text Description Figure
KMC-522310-3 Valve Q10 Blade cassette 1 - Cable
break or short circuit to UB
KMC-522310-6 Valve Q10 Blade cassette 1 - Short
circuit to ground
KMC-522311-3 Valve Q11 Blade cassette 2 - Cable
break or short circuit to UB
KMC-522311-6 Valve Q11 Blade cassette 2 - Short
circuit to ground
KMC-522312-3 Valve
- Q12.1 Rapid traverse of floor
conveyor 1
- Q12.2 Rapid traverse of floor
conveyor 2
- Cable break or short circuit to UB
KMC-522312-6 Valve
- Q12.1 Rapid traverse of floor
conveyor 1
- Q12.2 Rapid traverse of floor
conveyor 2
- Short circuit to ground
KMC-522313-3 Valve Q13 Load Sensing active -
Cable break or short circuit to UB
KMC-522313-6 Valve Q13 Load Sensing active -
Short circuit to ground
KMC-522314-3 Valve Q14 Coupling discharge rollers
- Cable break or short circuit to UB
KMC-522314-6 Valve Q14 Coupling discharge rollers
- Short circuit to ground
KMC-522315-3 Valve Q15 steering axle - Cable
break or short circuit to UB
KMC-522315-6 Valve Q15 steering axle - Short
circuit to ground
KMC-522318-3 Valve Q18 Pick-up 2 - Cable break or
short circuit to UB
KMC-522318-6 Valve Q18 Pick-up 2 - Short circuit to
ground
KMC-522319-3 Valve Q19 lift axle - Cable break or
short circuit to UB
Page 12
Error number Error text Description Figure
KMC-522319-6 Valve Q19 lift axle - Short circuit to
ground
KMC-522321-3 Valve K21 Pick-up drive - Cable break
or short circuit to UB
KMC-522321-6 Valve K21 Pick-up drive - Short
circuit to ground
KMC-522326-3 Valve K26 Pick-up relief - Cable
break or short circuit to UB
KMC-522326-6 Valve K26 Pick-up relief - Short
circuit to ground
KMC-522328-3 Valve Q28 Rapid traverse of floor
conveyor 1 - Cable break or short
circuit to UB
KMC-522328-6 Valve Q28 Rapid traverse of floor
conveyor 1 - Short circuit to ground
KMC-522329-3 Valve Q29 Rapid traverse of floor
conveyor 2 - Cable break or short
circuit to UB
KMC-522329-6 Valve Q29 Rapid traverse of floor
conveyor 2 - Short circuit to ground
KMC-522330-3 Valve Q30.1 Chopping flap 1 - Cable
break or short circuit to UB
KMC-522330-6 Valve Q30.1 Chopping flap 1 - Short
circuit to ground
KMC-522331-3 Valve Q30.2 Chopping flap 2 - Cable
break or short circuit to UB
KMC-522331-6 Valve Q30.2 Chopping flap 2 - Short
circuit to ground
KMC-522332-3 Valve Q32 Grinding discs drive -
Cable break or short circuit to UB
KMC-522332-6 Valve Q32 Grinding discs drive -
Short circuit to ground
KMC-522335-3 Valve Q35.1 Loading space cover 1 -
Cable break or short circuit to UB
Page 13
Error number Error text Description Figure
KMC-522335-6 Valve Q35.1 Loading space cover 1 -
Short circuit to ground
KMC-522336-3 Valve Q35.2 Loading space cover 2 -
Cable break or short circuit to UB
KMC-522336-6 Valve Q35.2 Loading space cover 2 -
Short circuit to ground
KMC-522337-3 Valve Q37.1 Front wall 1 - Cable
break or short circuit to UB
KMC-522337-6 Valve Q37.1 Front wall 1 - Short
circuit to ground
KMC-522338-3 Valve Q37.2 Front wall 2 - Cable
break or short circuit to UB
KMC-522338-6 Valve Q37.2 Front wall 2 - Short
circuit to ground
KMC-522339-3 Valve Q39 central lubrication unit -
Cable break or short circuit to UB
KMC-522339-6 Valve Q39 central lubrication unit -
Short circuit to ground
KMC-522351-23 Valve Q51 Release rear axle 1 -
Cable break, short circuit to earth or
short circuit to UB
KMC-522352-23 Valve Q52 Release rear axle 2 -
Cable break, short circuit to earth or
short circuit to UB
KMC-522353-23 Valve K53 Control rear axle 2 - Cable
break, short circuit to earth or short
circuit to UB
KMC-522354-23 Valve K54 Control rear axle 1 - Cable
break, short circuit to earth or short
circuit to UB
KMC-522355-23 Valve Q55 Release front axle 1 -
Cable break, short circuit to earth or
short circuit to UB
KMC-522356-23 Valve Q56 Release front axle 2 -
Cable break, short circuit to earth or
short circuit to UB
KMC-522357-23 Valve K57 Control front axle 2 - Cable
break, short circuit to earth or short
circuit to UB
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

Krone Messages - Parameters Operating instructions

Messages - Parameters
Krone
Brand
Krone
Model
Messages - Parameters
Type
Operating instructions
This manual is also suitable for

Krone Messages - Parameters, the device you just purchased, allows you to conveniently access and manage error messages and information messages related to your Krone machine. With its user-friendly interface, you can easily navigate through various error and information codes, getting clear descriptions and potential causes for each one. Whether you're a seasoned professional or new to Krone machinery, this device is designed to assist you in troubleshooting and maintaining your equipment efficiently.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents