Toro KIT-VXC REAR PANEL [HDX] User manual

Brand: Toro

Model: KIT-VXC REAR PANEL [HDX]

Type: User manual

Toro KIT-VXC REAR PANEL [HDX] is a specially designed accessory kit for Arctic Cat Prowler vehicles. It enables users to enhance the functionality and protection of their UTVs with the inclusion of a rear panel. This rear panel effectively encloses the cargo area, providing additional protection for stored items from external elements like dust, debris, and moisture. The kit also includes a two-piece roof, which overlaps the rear panel, offering comprehensive coverage and weather resistance.

The installation process is straightforward, and the kit comes with all the necessary hardware and detailed instructions. By following the provided steps, users can securely mount the rear panel and roof to their Prowler UTV, ensuring a snug fit and optimal functionality. Once installed, the rear panel and roof combination provide a secure and enclosed storage space, allowing users to transport their belongings with peace of mind, even in challenging outdoor conditions.

 NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain

these Installation Instructions for future reference.

Arctic Cat

Prowler

Installation Instructions - Accessory Kit

Form No. 0453-772

VXC (HDX) Rear Panel Kit

(1436-587)

Kit includes:

p/n QTY DESCRIPTION

N/A 1 Upper Rear Panel

N/A 1 Lower Rear Panel

2441-224 4 Rubber Clamp

* 1 Hardware Kit

0453-772 1 Instruction

1. Clean around the tail light; then apply Adhesive Foam

around the tail light. See Fig. 1.

Fig. 1

UTV-125A

2. Raise the cargo box; then secure Upper Rear Panel to

Lower Rear Panel using five M6 Torx-Head Screws,

five Flat Washers, and five M6 Lock Nuts. Tighten

securely. See Fig. 2.

Fig. 2

ROV-005A

3. Align the assembled rear panel onto the rear ROPS

tube.

4. Insert four Machine Screws and four Washers

through the outside of the rear panel and into the

four rubber clamps. Finger tighten using four

Nuts.

 NOTE: Install 2-piece roof kit (p/n 1436-519 with

the instructions included with that kit. The roof will

overlap the rear panel.

5. With the roof in position, insert two machine

screws and two washers through the outside of the

roof and top of the rear panel going into rubber

clamps on the ROPS tube (A). See Fig. 4.

6. Using a 1/4-in. drill bit, drill the remaining two

mounting locations (B) from inside (using the rear

panel as a hole template) the rear panel and

through the roof. Secure using two machine

screws and two washers through the outside of the

roof and top of the rear panel and fasten using

fender washers and nuts on the inside. See Fig. 3.

Fig. 3

UTV-277A

7. With the rear panel in position, locate the four

mounting locations for all four Rubber Clamps;

then place clamps onto rear ROPS tubes. See Fig.

Fig. 4

UTV-124A

8. Remove the cap screws and nuts securing the front

the the side cargo box panels; then replace with

two M10 Cap Screw, two M10 Flat Washers and

two Short Spacers. Secure using existing nuts.

Tighten securely. See Fig. 5 and 6.

Fig. 5

ROV-026A

Fig. 6

ROV-027A

9. Remove the three screws and spacers along the

back side of the cargo box. Replace with three M6

cap screw and three Long Spacers. Fasten using

existing nuts. Tighten securely. See Fig. 7 and 8.

Fig. 7

ROV-028A

Fig. 8

ROV-029A

10. Once optimal fitment is achieved, tighten all hard-

ware and latch the cargo box.

Printed in the U.S.A. ®™Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701 1212

Toro KIT-VXC REAR PANEL [HDX] User manual

Toro KIT-VXC REAR PANEL [HDX] User manual

Toro KIT-VXC REAR PANEL [HDX] User manual

Related papers

Other documents