Everbilt SF2000E Operating instructions

Everbilt
Brand
Everbilt
Model
SF2000E
Type
Operating instructions

Everbilt SF2000E is an 18-inch tank cover designed to fit most 18-inch sump and sewage basins. It comes with a riser cover, square drive screws and a #3 square driver for easy installation. The cover has four pre-drilled holes for easy mounting and a rubber seal to ensure a tight fit. It also features a 3-inch vent seal and a 4-inch basin inlet seal for added protection. The cover is made from durable materials and is backed by a one-year warranty.

Everbilt SF2000E is an 18-inch tank cover designed to fit most 18-inch sump and sewage basins. It comes with a riser cover, square drive screws and a #3 square driver for easy installation. The cover has four pre-drilled holes for easy mounting and a rubber seal to ensure a tight fit. It also features a 3-inch vent seal and a 4-inch basin inlet seal for added protection. The cover is made from durable materials and is backed by a one-year warranty.

HOMEDEPOT.com
Please contact 1-877-297-6069 for further assistance.
Installation
1
PREPARING FOR INSTALLATION
□ This 24 in. septic tank riser cover (A) will t most 24 in.
installed risers. Test t the riser cover (A) to ensure it is
correct for your riser.
□ Clean the sealing surface of your riser.
□ Remove the hardware pack containing the four square-drive
screws (B) from the back of the riser cover (A).
A
B
2
INSTALLING THE RISER COVER
□ Place the riser cover (A) on your riser. Ensure the rubber seal
is making a seal with the top of your riser.
□ Using the four screw holes in the riser cover (A) as a guide,
drill four 3/16 in. holes through your riser.
NOTE: Some risers may require the use of holes other than the molded
screw holes in the riser cover. For these risers, use the two additional
drill points molded on the top of the cover.
□ Install the screws (B) with a #3 square driver.
□ For access to your riser, remove the screws (B) and cover (A),
then reinstall.
A
B
Safety Information
WARNING: Failure to properly secure the riser cover will create a serious safety risk. Follow these installation instructions carefully.
Warranty
This product is warranted to the original consumer purchaser to be free from defects in material and workmanship for a period of one year from the date of
purchase. For additional details and questions, please contact Everbilt Customer Service at 1-877-297-6069.
TOOLS REQUIRED
Drill with 3/16 in. drill bit #3 Square Driver
PACKAGE CONTENTS
A - Riser Cover x1 B - Square drive screws x4
Use and Care Guide
18 in. Tank Cover
for Sewage Basin
Item # 1000027541
Model # SF2000E
WARNING: Failure to install basin cover as shown will create a safety risk. Install cover as shown.
NOTE: This 20.5” diameter cover with 19.5” bolt circle fits most 18” sump and
sewage basins. A 3” vent seal and 4” basin inlet seal are provided if
needed.
1. Unplug your pump.
2. Remove pipe and cord seals from cover.
3. Apply seal tape to basin rim inside the bolt circle as shown.
4. Pull your pump's power cord through the cover's cord hole as shown.
5. Slide the cover over the pump's discharge pipe through the discharge
opening as shown.
6. Bolt the cover down as shown with the discharge pipe positioned in the
center of the discharge opening. Do not overtighten. Slide the discharge
pipe seal over the discharge pipe and snap in place in the cover as
shown.
7. Slide the vent pipe seal up over your vent pipe. Position the vent pipe in
the center of the vent opening extending into the basin at least one inch.
The vent pipe will need to be self-supporting in this position as the seal
will not support the vent pipe. Snap the vent seal into the cover as shown.
8. Pull the pump's power cord through the cord opening, eliminating slack
inside the basin. Insert the cord through the cord hole in the cord seal and
press the cord seal into the cover as shown.
9. Install your check valve and the rest of your discharge plumbing to
complete your installation.
  • Page 1 1

Everbilt SF2000E Operating instructions

Everbilt
Brand
Everbilt
Model
SF2000E
Type
Operating instructions

Everbilt SF2000E is an 18-inch tank cover designed to fit most 18-inch sump and sewage basins. It comes with a riser cover, square drive screws and a #3 square driver for easy installation. The cover has four pre-drilled holes for easy mounting and a rubber seal to ensure a tight fit. It also features a 3-inch vent seal and a 4-inch basin inlet seal for added protection. The cover is made from durable materials and is backed by a one-year warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents