Makita ML122 User manual

Rechargeable Job Site Light

Lampe

a

batterie

Linterna fluorescente a bateria

,

ML122 ML123

Page is loading ...

ML12

7

Symbols

The following show the symbols used for the tool, Be sure that

you

understand their meaning before use.

Symboles

Nous

donnons ci-dessous les symboles utilises pour I'outil. Assurez-vous que vous en avez bien compris la

signification avant d'utiliser I'outil.

Sfmbolos

A continuacion se muestran

10s

simbolos utilizados con esta herramienta. Asegurese de que entiende

su

significado antes de usarla.

0

Read instruction manual.

0

Lire le mode d'emploi.

0

Lea

el

manual de instrucciones

I

rl

0

Do

not touch the fluorescent tube which is hot in use or immediately after putting

out

light.

You

may get burnt.

chaude et vous risqueriez de vous brcler.

0

Ne pas toucher I'ampoule en cours d'utilisation

ou

immbdiatement apres I'avoir eteinte. Elle est

ON0

toque la bombilla mientras este siendo usada ni inmediatamente despues de haberla

apagado porque estara caliente. Podria quemarse

3

ENGLISH

Exdanation

of

general

view

1

Battery cartridge

6

Hook (ML122 only)

2 Set plate

7 Strap (ML122 only)

3

Screw

8

Fluorescent tube

4 Ring 9 Lamp cover

5

Reflector (ML122 only)

10

Connecting ring

11

Switch

12 Cap

13

Metal fitting

14 Hook (ML123 only)

15

Reflector (ML123 only)

SPECIFICATIONS

Model ML122 ML123

Power source

.............................

D.C. 12

V

/

9.6

V

D.C. 12

V

19.6

V

Fluorescent tube

........................

Compact FL13

W

Compact FL13 W

Dimensions

(L

x

W

x

H)

............

347 mm

x

97 mm

x

94 mm 411 mm

x

97 mm

x

94 mm

(when the hook is pulled

out)

350

mm

x

97 mm

x

94 mm

(when the hook is stored)

0.37 kg

Net weight

...................................

0.35

kg

Due to our continuing program of research and development, the specifications herein are subject

to

change

Note: Specifications may differ from country

to

country.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

When using electric

tools,

basic safety precautions should always be followed to reduce the risk of fire, electric

shock, and personal injury, including the following:

without notice.

READ ALL INSTRUCTIONS.

1.

Read this instruction manual and the charger instruction manual carefully before use.

2. This tool is not water-proof.

Do

not use

it

in

damp or wet locations.

Do

not expose

it

to rain or snow.

Do

not wash

it

in

water.

3.

A short-circuit can cause a large current flow, overheating, possible burns and even a breakdown.

(1)

Do

not touch the battery terminals with any conductive materials.

(2) Avoid storing the battery cartridge in a container with any metal objects such as nails, coins, etc.

4.

Never expose the battery cartridge to flames, fire or great heat. Breakage may cause release of

injurious material.

5.

Do

not disassemble the charger or battery Cartridge; take

it

to a qualified serviceman when service

or repair is required. Incorrect reassembly may result

in

a risk of electric shock or fire.

6.

When the tool is not

in

use, always switch

off

and remove the battery cartridge from the tool.

7.

Do

not give the tool a shock by dropping, striking, etc.

8.

Do

not expose the light to eyes continuously.

It

may

hurt

them.

9.

Do

not cover or clog the

lit

tool with cloth or carton, etc.

It

may create

a

risk of fire.

10. if you notice that the tool is hot or In abnormal condition, consult your nearest Maklta Service

Center or dealer.

When the switch is turned

“ON”,

the handle of the tool may become slightly hot, even if the

fluorescent tube is not instailed or is not lighted. This is

a

normal condition and does not indicate

problem.

11.

If

any problem develops, consult your nearest Makita Service Center or dealer. To maintain product

safety and reliability, repairs, maintenance or adjustment should be carried out by Makita

Authorized Service Center.

12. Switch

off

the light immedlately when the lamp gets dark

in

use. if you leave the lamp switched on,

the battery cartridge capacity may decrease.

SAVE THESE INSTRUCTIONS.

4

For

U.S.A

only

Recycling the Battery

The only way to dispose

of

a Makita battery

is

to recycle it. The law

prohibits any other method

01

disposal.

Battery cartridge

1200, 1200A, 1220

1202, 1202A, 1222

To

recycle the battery:

1. Remove the battery from the tool.

2. a) Take the battery

to

your nearest Makita Factory Service Center

or

Operating time Charger

DC1470, DC1201, DC1411,

DC1422, DC1439, DC1801

DC1201, DC1411, DC1422,

DC1439. DC1801

Approx.

80

min.

Approx. 130 min.

I

Ni-Cd

1235

9100, 9120

9102, 9102A, 9122

91 33

91 34

91 35

b) Take the battery

to

your nearest Makita Authorized Service Center or Distributor that has been

designated as a Makita battery recycling location.

Call your nearest Makita Service Center

or

Distributor

to

determine the location that provides Makita

battery recycling. See your local Yellow Pages under "Tools-Electric".

Approx. 190 min.

DC9710, DC9711, DC1470,

DC1201, DC1411, DC1422,

DC1439, DC1801

DC1201, DC1411, DC1422,

DC1439, DCl80l

Approx.

80

min.

Approx. 130 min.

Approx. 140 min.

Approx. 170 min.

Approx. 190 min.

-

DC9711, DC1411, DC1422,

-

DC1439, DC1801

OPERATING INSTRUCTIONS

Charging

Charge the battery cartridge with the Makita charger before use. To remove the battery cartridge, withdraw it

from the

tool

while pressing the buttons on both sides of the cartridge. After charging, insert the battery cartridge

into the

tool

all the way until it locks in place with a little click.

(Fig.

1)

NOTE:

Battery cartridges 9100, 9102, 9102A, 9120, 9122, 9133, 9135, 1200, 1202, 1200A, 1202A can be used on

ML122/ML123

if

you install the set plate. Install the set plate on ML122/ML123 with the screw.

(Fig.

2)

The following tables indicate the operating time on a single charge.

Voltage

12

v

9.6

V

(Note)

If

you use a power checking battery on Model ML122/ML123. the power checking battery will not indicate the

remaining battery capacity properly.

Storing battery cartridge

Always charge the Nickel Metal Hydride battery cartridge before storing it when you

do

not use it for more than

six months.

Switch action

To turn on the light, depress the switch. Depress the switch once again, the light is turned

off

5

Replacing fluorescent tube

(Fig.

3

&

4)

CAUTION:

1,

Do

not give the fluorescent tube a shock or mar it. It may result in a risk of breakage of the glass and a

serious personal injury.

2.

Do

not touch the fluorescent tube which is hot in use or immediately after putting out light. You may get

burnt.

3.

Always be sure that the battery cartridge is removed before replacing the fluorescent tube or maintenance.

Remove the connecting ring and pull the lamp cover straight out to remove it. Then remove the cap and pull

the tube to replace the tube.

To install the lamp cover, place the cap on the tube. Then insert the lamp cover

so

that the protrusion on the

tool fits into the groove on the lamp cover. And insert the connecting ring

so

that the pin on the connecting ring

fits into the groove on the lamp cover.

Strap

and

hook

Install the strap on the tool.

(Flg.

5)

When storing the tool, hang the metal fitting of the strap on the ring of the

tool.

(Fig.

6)

CAUTION

:

Do

not shake the tool when the hook is pulled out. The hook can catch something accidentally.

Do

not use the hook except when you hang the tool. This may result

in

a risk of breakage

of

the

tool.

The hook can be turned, slid and stored around the lamp cover.

(Fig.

7)

The hook also can be removed when you do not use it.

To

maintain product safety and reliability, repairs, maintenance

or

adjustment should be carried out by a Makita

Authorized Service Center.

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for use with your Makita tool specified in this manual. The

use

of

any other accessories or attachments might present a risk of injury

to

persons. The accessories or

attachments should be used only

in

the proper and intended manner.

Fluorescent tube

Page is loading ...

Makita ML122 User manual

This manual is also suitable for

Makita ML122 User manual

in other languages

Related papers

Other documents