DALI Scene Controller for Motion Sensor with Fixed Scenes
09.2412SB.04790
Function introduction
Important: Read All Instructions Prior to Installation
Output DALI signal
Operation Current 4mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions
Product Data
Power Supply Supply By DALI Bus
Wiring Diagram
DALI bus
V+ V-
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V/36V
CV PSU
DALI Controlle r
123
4
0-6 0 -9
DA DA
V+ V-
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V/36V
CV PSU
DALI Controlle r
123
4
0-6 0 -9
LDA
DALI OUTPUT
DA
N
AC INPUT
(motion sensor)
DALI Scenes
(for motion sensor)
Power by DALI bus Rotary Switch for Setting
Delay Time 1 (Total 16
different Delay Times)
Rotary Switch for Assigning
Group (Total 16 Groups)
Rotary Switch for Setting
Delay Time 2 (Total 16
different Delay Times)
DALI signal outputSensor input
45.5x45x20.3mm
• Control up to 16 different groups.
• Control all devices on DALI circuit through broadcast.
• Recall 3 fixed predefined DALI scenes.
• Enable to set 16 different delay times.
• Can connect with different motion sensors.
• Can connect with different types of motion sensors
including PIR, microwave etc.
• Each DALI bus can install multiple scene controllers,
consumption current of each controller is 4mA.
• Multiple motion sensors can be connected to one scene
controller for multi operation points.
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
LDA
DALI OUTP UT
DA
N
AC INPUT
(motion s ensor )
Delay Time 2
DALI Scenes
(for motion sensor)
Power by DA LI bus
1. Do wiring according to connection diagram correctly.
2. Set starting Group number via rotary switch on the back: (0-15 selectable)
• This DALI scene controller enables Group selection commands to be sent to 1 Group of DALI devices on the DALI
circuit for Scene control. A rotary switch is used to select the DALI Group you would like to control and set the starting
Group number, and total 16 Groups (0-15) can be selected.
• When the rotary switch arrow position is at 0, all devices on DALI circuit will be selected for Scene control through
broadcast.
• When the rotary switch arrow position is at X except 0 (1-15), devices in DALI Group X-1 will be selected for Scene
control.
For example: Rotary switch arrow at 1, DALI Group 0 will be selected. Rotary switch arrow at 15, DALI Group 14 will be
selected.
Note: Please configure the slave controllers on DALI circuit to the DALI Group you would like to select with DALI master.
Please refer to the detailed Group setting table as follows:
Rotary Switch
Position
DALI Group
Selected
0
Broadcast
1
0
2
1
3
2
4
3
5
4
6
5
7
6
8
7
9
8
10
9
11
10
12
11
13
12
14
13
15
14
Operation
Delay Time 1
Delay Time 2
Delay Time 1
DA
DA
DA
DA
DAL I DALI
V+
V-
V+
V-
12- 36VDC
INP UT
DA
DA
DA
DA
DAL I DALI
V+
V-
V+
V-
12- 36VDC
INP UT
Sensor Input
L
N
Different types of motion sensors
including PIR, microwave etc.
3. DALI Scenes to be recalled
3 fixed predefined DALI scenes will be recalled by the DALI scene controller and the command will be triggered
by the connected motion sensor:
When presence of a human being is detected within detection range in a room, a predefined scene S1 will be triggered
and recalled to the selected DALI Group.
When absence of the human being is detected within detection range after the time he stayed in the room, a predefined
scene S2 will be triggered and recalled to the selected DALI Group. The time that the selected DALI Group needs to
reach light value of S2 from value of S1 can be set by the rotary switch Delay Time 1 on the back.
The scene S2 will last for a period depending on the selected Delay Time 2, when the delay time elapsed, a predefined
scene S3 will be triggered and recalled to the selected DALI Group.
S1, S2 and S3 will be fixed to the last three DALI Scenes (13, 14, 15 or 14, 15, 16 depending on different starting DALI
Scene number 0 or 1 stored in salve controllers).
Note: Please configure light value of the last three DALI Scenes to the slave controllers on DALI circuit with DALI master.
4.Set Delay Time 1 (from S1 to S2)
The time that the selected DALI Group needs to reach light value of S2 from value of S1 can be set by the rotary switch
Delay Time 1. Once absence of human being is detected, the scene S1 will fade to scene S2 within the selected Delay
Time 1. Total 16 different delay times (0-15) can be selected, 0S means no fade, S1 directly goes to S2. The detailed
selectable delay time 1 are as follows:
Rotary Switch
Position 01 2 345678 9 10 11 12 13 14 15
Delay Time1 0S 0.7S 1.0S 1.4S 2.0S
5.Set Delay Time 2 (from S2 to S3)
A rotary switch is used to set Delay Time 2 from S2 to S3, once scene S2 is recalled, it will last for the Delay Time 2 and
S3 will be recalled once time elapsed. Total 16 different delay times (0-15) can be selected. 0 stands for no delay, which
means scene S1 will directly go to scene S3 without S2 being recalled. 15 stands for infinity, which means the Delay
Time is infinite and scene S2 will never go to scene S3. The delay time selectable are as follows:
2S 5S 10S 30S 1Min 10
Min
20
Min
30
Min
40
Min
60
Min
90
Min
120
Min
150
Min
240
Min
Infinity
2.8S 4.0S 5.7S 8.0S 11.3
S
16.0
S
22.6
S
32.0
S
45.3
S
64.0
S
90.5
S
Rotary Switch
Position 01 2 345678 9 10 11 12 13 14 15
Delay Time2 0S
45.00 mm
45.50 mm
20.3 mm
Product Dimension
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sunricher SR-2411-RF-RGBW User manual
-
-
-
-
-
-
-
-
-
Other documents
-
HELVAR DIGIDIM-Toolbox User guide
-
Mean Well PWM-120-12BLE User manual
-
DIODE LED CASAMBI Controllers User guide
-
Eltako FDG71L-230V User manual
-
ABB i-bus DALI-Gateway DG/S 8.1 User manual
-
-
-
-
Hager TX216 Product Documentation
-
LUNATONE DALI Touchpanel User manual
