2. Durabook
  3. R11
R11

Durabook R11 User manual

  • Hello! I'm your chat assistant. I have analyzed this user manual for the DURABOOK R11 LF/HF RFID expansion module and I'm ready to answer questions about the installation process. It covers the step-by-step process of how to install the LF/HF RFID module, including connecting the expansion FFC, installing the bracket and cover, and securing it all with the correct screws and torque. Feel free to ask any questions!
  • What should I do if any item is damaged upon arrival?
    What should I remove before installing expansion modules?
    How to secure the RFID module cover?
©2022 Twinhead International Corp and/or its affiliates. All rights reserved.
1
R11 Rugged Tablet
Expansion Modules
LF/HF RFID
P/N: 62+030990+10
Expansion Modules_ LF/HF RFID
2
Package Contents
If any of following items is damaged, please contact your retailer.
RFID module cover
RFID module
Expansion sponge
RFID module bracket
Gasket
Sponges
RFID expansion board
Expansion FFC
Screws
LF/HF RFID Module Screws
Screw Name
Quantity
ISOT-M2.0X4L
2 (bracket to lower case)
ISOT-M2.6X4L
2 (expansion board to bracket)
M2.6X6L
& O RING
4 (cover to lower case)
NOTE
The pictures are for reference only, actual items may slightly differ.
Expansion Modules_ LF/HF RFID
3
Installation
This section will guide you on how to install the expansion modules to your tablet
PC.
Note: Make sure to remove the battery before installing any type of expansion
modules. For more information on how to remove/install the battery, please refer
to the tablet PC service guide.
Installing the LF/HF RFID Module
To install the LF/HF RFID module, follow the steps below:
1. Remove the screw securing the mylar on the DDR door.
2. Remove the mylars from the DDR door.
Expansion Modules_ LF/HF RFID
4
3. Attach the expansion sponge to the DDR door. Then install the sponges onto
the screw holes.
4. Connect the expansion FFC to the mainboard connector. Then secure the
latch.
5. Route the expansion FFC through the opening on the RFID module bracket.
Then, by aligning with the screw holes, install the bracket onto its slot on the
lower case.
Expansion Modules_ LF/HF RFID
5
6. Attach the 2 screws to secure the RFID module bracket to the lower case.
7. Connect the expansion FFC to the RFID expansion board connector. Then
secure the latch.
8. Attach the tape to secure the expansion FFC in place.
Expansion Modules_ LF/HF RFID
6
9. Flip the RFID expansion board. Then, by aligning with the screw holes, install
the RFID expansion board onto its slot on the RFID module bracket.
10. Attach the 2 screws to secure the RFID expansion board to the bracket.
11. Connect the RFID module FFC to the RFID expansion board connector. Then
secure the latch.
Expansion Modules_ LF/HF RFID
7
12. Attach the tape to secure the RFID module FFC in place.
13. Detach the protective sheet from the RFID sponge. Then, by aligning the
bottom right edge of the RFID module (marked by orange line) with “L”
engraved line on the bracket, attach the RFID module onto its slot on the
bracket.
14. Fold the RFID module FFC. Then attach the tape to secure the FFC in place.
Expansion Modules_ LF/HF RFID
8
15. By aligning with the screw holes, place the gasket onto the installed bracket.
16. By aligning with the screw holes, place the RFID module cover onto the
installed gasket.
17. Attach the 4 screws to secure the RFID module cover to the lower case.
18. Install the battery.
Expansion Modules_ LF/HF RFID
9
LF/HF RFID Module Screws
Screw Name
Quantity
Torque
ISOT-M2.0X4L
2 (bracket to lower
case)
2.0 ±0.3 Kgf-cm
ISOT-M2.6X4L
2 (expansion board
to bracket)
2.0 ±0.3 Kgf-cm
M2.6X6L
& O RING
4 (cover to lower
case)
2.5 ±0.3 Kgf-cm
Twinhead International Corp.
11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.
/