Sony VPL-HW50ES User manual

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for

future reference.

VPL-HW50ES

4-439-386-11

(

1

)

E:\DATA\4439386111\4439386111VPLHW50ESUC\00COV-

VPLHW50ESUC\010COV.fm

masterpage:Back

Cover

4-439-386-11 (1)

Video Projector

VPL-HW30ES/HW30AES

4-290-338-13 (1)

E:\DATA\4439386111\4439386111VPLHW50ESUC\00COV-

VPLHW50ESUC\100BCO.fm

masterpage:Back

Cover

S

ony Corporation

Printed in Japan

2

To reduce the risk of fire or

electric shock, do not expose

this apparatus to rain or

moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

THIS APPARATUS MUST BE

EARTHED.

For the customers in the U.S.A. and

Canada

WARNING:

Using this unit at a voltage other than 120 V

may require the use of a different line cord or

attachment plug, or both. To reduce the risk

of fire or electric shock, refer servicing to

qualified service personnel.

For the customers in the U.S.A.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in

a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

All interface cables used to connect

peripherals must be shielded in order to

comply with the limits for a digital device

pursuant to Subpart B of Part 15 of FCC

Rules.

If you have any questions about this product,

you may call;

Sony Customer Information Service Center

1-800-222-7669 or http://www.sony.com/

For the customers in Canada

This Class B digital apparatus complies with

Canadian ICES-003.

For the customers in Europe

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, 108-0075 Japan.

The Authorized Representative for EMC

and product safety is Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327

Stuttgart, Germany. For any service or

guarantee matters please refer to the

addresses given in separate service or

guarantee documents.

WARNING

Declaration of Conformity

Trade Name: SONY

Model: VPL-HW50ES

Responsible party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127

U.S.A.

Telephone Number:858-942-2230

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

3

Afin de réduire les risques

d’incendie ou d’électrocution,

ne pas exposer cet appareil à

la pluie ou à l’humidité.

Afin d’écarter tout risque

d’électrocution, garder le

coffret fermé. Ne confier

l’entretien de l’appareil qu’à

un personnel qualifié.

CET APPAREIL DOIT ÊTRE

RELIÉ À LA TERRE.

Pour les clients au Canada

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

Pour les clients en Europe

Le fabricant de ce produit est Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, 108-0075 Japon.

Le représentant autorisé pour EMC et la

sécurité des produits est Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327

Stuttgart, Allemagne. Pour toute question

concernant le service ou la garantie, veuillez

consulter les adresses indiquées dans les

documents de service ou de garantie séparés.

Um die Gefahr von Bränden

oder elektrischen Schlägen zu

verringern, darf dieses Gerät

nicht Regen oder Feuchtigkeit

ausgesetzt werden.

Um einen elektrischen Schlag

zu vermeiden, darf das

Gehäuse nicht geöffnet

werden. Überlassen Sie

Wartungsarbeiten stets nur

qualifiziertem Fachpersonal.

DIESES GERÄT MUSS

GEERDET WERDEN.

Für Kunden in Europa

Der Hersteller dieses Produkts ist Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, 108-0075 Japan.

Der autorisierte Repräsentant für EMV und

Produktsicherheit ist Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327

Stuttgart, Deutschland. Bei jeglichen

Angelegenheiten in Bezug auf

Kundendienst oder Garantie wenden Sie

sich bitte an die in den separaten

Kundendienst- oder Garantiedokumenten

aufgeführten Anschriften.

For kundene i Norge

Dette utstyret kan kobles til et IT-

strømfordelingssystem.

Für Kunden in Deutschland

Entsorgungshinweis: Bitte werfen Sie nur

entladene Batterien in die Sammelboxen

beim Handel oder den Kommunen. Entladen

sind Batterien in der Regel dann, wenn das

Gerät abschaltet und signalisiert „Batterie

leer“ oder nach längerer Gebrauchsdauer der

Batterien „nicht mehr einwandfrei

funktioniert“. Um sicherzugehen, kleben Sie

die Batteriepole z.B. mit einem

Klebestreifen ab oder geben Sie die

Batterien einzeln in einen Plastikbeutel.

AVERTISSEMENT

WARNUNG

4

For the customers in Taiwan only

For the Customers in Brazil only

DESCARTE DE PILHAS E BATERIAS

Bateria Primária

Atenção:

Verifique as instruções de uso do aparelho

certificando-se de que as polaridades (+) e

(-) estão no sentido indicado. As pilhas

poderão vazar ou explodir se as polaridades

forem invertidas, expostas ao fogo,

desmontadas ou recarregadas.

Evite misturar com pilhas de outro tipo ou com

pilhas usadas, transportá-las ou armazená-las

soltas, pois aumenta o risco de vazamento.

Retire as pilhas caso o aparelho não esteja

sendo utilizado, para evitar possíveis danos

na eventualidade de ocorrer vazamento.

As pilhas devem ser armazenadas em local

seco e ventilado.

No caso de vazamento da pilha, evite o

contato com a mesma. Lave qualquer parte

do corpo afetado com água abundante.

Ocorrendo irritação, procure auxílio médico.

Não remova o invólucro da pilha.

Mantenha fora do alcance das crianças. Em

caso de ingestão procure auxílio médico

imediatamente.

DESCARTE DE PILHAS E BATERIAS

Este produto contém bateria de alimentação

integrada (não removível pelo usuário) que

só deve ser substituída por profissionais

qualificados. Ao fim da vida útil do

equipamento, disponha-o em um ponto de

coleta na Rede Autorizada Sony ou nas lojas

Sony, de forma a garantir o tratamento

adequado da bateria.

5

Table of Contents

Precautions .........................................7

Front/Right Side .................................8

Rear/Bottom .......................................9

Remote Control ................................10

Unpacking ........................................11

Step 1: Installing the Projector .........13

Before Setting Up the

Projector .....................................13

Positioning the Projector and a

screen ..........................................16

Step 2: Adjusting the Picture

Position .............................................20

Step 3: Connecting the Projector .....25

Connecting to a VCR .................25

Connecting to a Computer ..........27

Connecting to a 3D Sync

Transmitter .................................28

Step 4: Selecting the Menu

Language ..........................................29

Projecting the Picture .......................31

Turning Off the Power ...............32

Selecting the Aspect Ratio According to

the Video Signal ...............................33

Watching 3D Video Images .............36

Using the Simulated 3D

Function ......................................37

Using the 3D Glasses ................. 37

Selecting the Picture Viewing

Mode ............................................... 40

Using “ImageDirector3” to Adjust

the Picture Quality ........................... 41

Adjusting the Picture Quality .......... 42

Selecting to Directly Adjust the

Desired Menu Item .................... 42

Adjusting the Picture Using Real Color

Processing ........................................ 43

Operation through the Menus .......... 45

Picture Menu ................................... 49

Advanced Picture Menu .................. 54

Screen Menu .................................... 55

Setup Menu ...................................... 57

Function Menu ................................. 59

Items Locked by Settings

Lock ......................................... 62

Installation Menu ............................. 63

Information Menu ............................ 65

About the Preset Memory No. ... 66

About the Control for HDMI ........... 67

About the x.v.Color ......................... 68

About the simulated 3D feature ....... 68

Troubleshooting ............................... 69

Warning Indicators .................... 72

Message Lists ............................. 73

Location of Controls

Connections and

Preparations

Projecting

Using the Menus

Others

6

Replacing the Lamp and the Air Filter

and Cleaning the Ventilation Holes

(intake) ............................................. 75

Cleaning the Air Filter ..................... 78

Fitting the Lens Cap ......................... 78

Cleaning and the Screen of the

Projector ........................................... 79

Specifications ................................... 79

Preset Signals ............................. 81

Input Signals and Adjustable/

Setting Items ............................... 83

Compatible 3D Signals .............. 85

3D Signals and Adjustable/

Setting Items ............................... 85

Aspect Mode .............................. 87

Storage Conditions of Adjustable/

Setting Items ............................... 88

Ceiling Installation ........................... 90

Index ............................................... 94

Trademark Information

“PS3” is a registered trademark of Sony

Computer Entertainment Inc.

HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing

LLC.

“Blu-ray” and “Blu-ray Disc” are trademarks

of Blu-ray Disc Association.

..........................................................................

Control for HDMI is an HDMI standard mutual

control function which uses the HDMI CEC

(Consumer Electronics Control) specification.

This projector supports DeepColor, x.v.Color,

LipSync, 3D signal and computer input signal

of HDMI standards. It also supports HDCP.

7

Precautions

On safety

• Check that the operating voltage of your

unit is identical with the voltage of your

local power supply.

• Should any liquid or solid object fall into

the cabinet, unplug the unit and have it

checked by qualified personnel before

operating it further.

• Unplug the unit from the wall outlet if it is

not to be used for several days.

• To disconnect the cord, pull it out by the

plug. Never pull the cord itself.

• The wall outlet should be near the unit and

easily accessible.

• The unit is not disconnected to the AC

power source (mains) as long as it is

connected to the wall outlet, even if the

unit itself has been turned off.

• Do not look into the lens while the lamp is

on.

• Do not place your hand or objects near the

ventilation holes. The air coming out is

hot.

On preventing internal heat build-

up

After you turn off the power with the I/1

(ON/STANDBY) switch, do not disconnect

the unit from the wall outlet while the

cooling fan is still running.

Caution

The projector is equipped with ventilation

holes (intake) and ventilation holes

(exhaust). Do not block or place anything

near these holes, or internal heat build-up

may occur, causing picture degradation or

damage to the projector.

On repacking

Save the original shipping carton and

packing material; they will come in handy if

you ever have to ship your unit. For

maximum protection, repack your unit as it

was originally packed at the factory.

Safety precautions when using 3D

Glasses

Warning

• Do not put the 3D Glasses in a fire.

• Do not disassemble the 3D Glasses.

• Do not use, charge, store, or leave the 3D

Glasses near a fire, or in places with a high

temperature, e.g., in direct sunlight, or in

sun-heated cars.

• Use only the supplied USB cable.

• Do not allow water or foreign material to

enter the 3D Glasses.

Safety precautions

• Use only the type of 3D glasses included

with this unit. You should only use the 3D

glasses for watching 3D video images. Do

not use the 3D Glasses with other

equipment, such as TV.

• If you observe flickering or flashing, turn

off the lighting in the room.

• Not for use by children without proper

adult supervision.

• Be careful not to pinch your fingers in

hinges of the 3D glasses when bending the

temple frames.

• Do not drop or modify these 3D glasses.

• If these glasses are broken, keep broken

pieces away from your mouth or eyes.

8

Front/Right Side

You can use the buttons on the control panel with the same names as those on the remote

control to operate the projector.

Location of Controls

INPUT button (1 page 31)

MENU button (1 page 45)

ON/STANDBY

indicator

(1 page 20)

Remote control detector

Ventilation

holes (exhaust)

(1 page 14)

?/1 (ON/STANDBY) switch (1 page 21)

LAMP/COVER

indicator

(1 page 72)

M/m/</, (arrow)/

(enter) button (1 page 45)

Ventilation holes (exhaust) (1 page 14)

- AC IN socket

Y P

B/CB PR/CR connector (phono type) (1 page 26)

INPUT A connector (1 page 27)

HDMI 1 connector (1 page 25)

REMOTE connector

Connects to a computer,

etc. for remote control

HDMI 2 connector (1 page 25)

While the ON/STANDBY indicator

lights in orange, the power saving

mode is on. (1 page 58)

Note

Lens shift dials (1 page 21)

Zoom lever (1 page 23)

Focus ring (1 page 23)

Control panel

IR IN connector

Inputs signals to control the projector

3D SYNC connector (1 page 28)

9

Location of Controls

Rear/Bottom

Filter holder (1 page 77)

Ventilation holes (intake)

(1 page 14)

Lamp cover (1 page 76)

Ventilation holes (intake)

(1 page 14)

Projector suspension

support attaching hole

(1 page 90)

Front feet (adjustable) (1 page 24)

Ventilation holes (intake)

(1 page 14)

Ventilation holes (intake)

(1 page 14)

Ventilation holes (intake)

(1 page 14)

3D Sync Transmitter

(1 page 38)

10

Remote Control

INPUT button (1 page 31)

Infrared transmitter

?/1 (On/standby)

switch (1 page 21)

COLOR SPACE button

(1 page 42)

M/m/</, (arrow)/ (enter)

buttons (1 page 45)

RESET button (1 page 45)

CONTRAST +/– button

(1 page 51)

BRIGHTNESS +/– button

(1 page 51)

LIGHT button

Illuminates the buttons on

the remote control.

CALIBRATED PRESET

buttons (1 page 40)

3D button (1 page 59)

ASPECT button

(1 page 33)

PATTERN button

(1 page 21)

SHARPNESS +/– button

(1 page 51)

MENU button (1 page 45)

REALITY CREATION

button (1 page 50)

COLOR TEMP button

(1 page 42)

RCP (Real Color Processing)

button (1 page 43)

ADVANCED IRIS

button (1 page 42)

GAMMA CORRECTION

button (1 page 42)

MOTION ENHANCER

button (1 page 42)

11

Connections and Preparations

This section describes how to install the projector and screen, how to connect the

equipment from which you want to project the picture, etc.

Unpacking

Check the carton to make sure it contains the following items:

Inserting the batteries into the remote control

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

When you dispose of the battery, you must obey the law in the relative area or country.

ATTENTION

Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer

uniquement avec une batterie du même type ou d’un type équivalent recommandé par le

constructeur.

Lorsque vous mettez la batterie au rebut, vous devez respecter la législation en vigueur

dans le pays ou la région où vous vous trouvez.

Connections and Preparations

• Remote control (1) and

Size AA (R6) manganese batteries (2)

• AC power cord (1)

• Lens cap (1)

When you have purchased the projector,

the lens cap is put onto the lens.

Remove this lens cap when you use the

projector.

• 3D glasses (2)

• Pouch for the 3D glasses (2)

• USB charging cable (GPHK05-2010-

0007/SONY) (1.2 m) (1)

• Operating Instructions (this manual)

• Operating Instructions for the 3D

glasses (1)

Insert the batteries

E

side first as shown in the illustration.

Inserting them forcibly or with the polarities reversed may

cause a short circuit and may generate heat.

Push and slide to open.

12

VORSICHT

Explosionsgefahr bei Verwendung falscher Batterien. Batterien nur durch den vom

Hersteller empfohlenen oder einen gleichwertigen Typ ersetzen.

Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des

jeweiligen Landes befolgen.

Installing batteries

Two size AA (R6) batteries are supplied for Remote Control.

To avoid risk of explosion, use size AA (R6) manganese or alkaline batteries.

Caution about handling the remote control

• Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind

onto it.

• Do not place the remote in a location near a heat source, a place subject to direct

sunlight, or a damp room.

13

Connections and Preparations

Step 1: Installing the Projector

The projector displays pictures output from

a VCR or other device.

The lens shift allows you to have broader

options for placing the projector and

viewing pictures easily.

Unsuitable installation

Do not place the projector in the following

situations, which may cause malfunction

or damage to the projector.

Poorly ventilated location

Leave space of more than 30 cm (11

7

/

8

inches)

around the unit.

Hot and humid

Locations subject to direct cool or

warm air from an air-conditioner

Installing the projector in such a location

may cause a malfunction of the unit due to

moisture condensation or rise in

temperature.

Near a heat or smoke sensor

Malfunction of the sensor may occur.

Very dusty and extremely smoky

locations

Install in a location away from walls

To maintain the performance and

reliability of the projector, allow at

least 30 cm (11 7/8 inches) between

the projector and walls.

Before Setting Up the

Projector

30 cm

(11

7

/

8

inches)

30 cm

(11

7

/

8

inches)

30 cm

(11

7

/

8

inches)

30 cm

(11

7

/

8

inches)

14

Improper use

Do not do any of the following while using

the projector.

Blocking the ventilation holes (intake

or exhaust)

Tip

For details on the location of the ventilation

holes (intake or exhaust), see “Location of

Controls” (1 page 8).

Tilting front/rear and left/right

Avoid using the projector tilted at an angle

of more than 15 degrees.

Do not install the projector anywhere other

than on a level surface or on the ceiling.

Installing the projector in such a location

may result in uneven color uniformity or

reduce the reliability of the effects of the

lamp.

If the projector is tilted up or down, the

image on the screen may be trapezoidal.

Position the projector so that the lens is

parallel to the screen (1 page 19).

When installing the unit at altitudes

When using the projector at an altitude of

1,500 m or higher, set “Cooling Setting” in the

Setup menu to “High” (1 page 57).

Failing to set this mode when using the

projector at high altitudes could have adverse

effects, such as reducing the reliability of

certain components.

WARNING

When installing the unit, incorporate a readily

accessible disconnect device in the fixed

wiring, or connect the power plug to an easily

accessible socket-outlet near the unit. If a fault

should occur during operation of the unit,

operate the disconnect device to switch the

power supply off, or disconnect the power

plug.

AVERTISSEMENT

Lors de l’installation de l’appareil, incorporer

un dispositif de coupure dans le câblage fixe ou

brancher la fiche d’alimentation dans une prise

murale facilement accessible proche de

l’appareil. En cas de problème lors du

fonctionnement de l’appareil, enclencher le

dispositif de coupure d’alimentation ou

débrancher la fiche d’alimentation.

Ventilation holes

(exhaust)

Ventilation holes

(intake)

15° or more

15

Connections and Preparations

WARNUNG

Beim Einbau des Geräts ist daher im Festkabel

ein leicht zugänglicher Unterbrecher

einzufügen, oder der Netzstecker muss mit

einer in der Nähe des Geräts befindlichen,

leicht zugänglichen Wandsteckdose verbunden

werden. Wenn während des Betriebs eine

Funktionsstörung auftritt, ist der Unterbrecher

zu betätigen bzw. der Netzstecker abzuziehen,

damit die Stromversorgung zum Gerät

unterbrochen wird.

16

The installation distance between the projector and a screen varies depending on the size

of the screen or whether or not you use the lens shift features.

1 Determine the installation position of the projector and screen.

You can obtain a good quality picture if you position the projector so that the center

of the lens is within the area indicated in gray in the illustration.

Use the values L, x and y in the table on page 17 or 18 as a guide.

* Installation position not using lens shift (x = 0, y = 0)

** Example of installation position using lens shift (x, y)

L: Distance between the screen and the front end of the projector’s lens.

x: Horizontal distance between the center of the screen and the center of the

projector’s lens.

y: Vertical distance between the center of the screen and the center of the projector’s

lens.

For installation of the projector on a ceiling, see “Ceiling Installation.”

(1 page 90)

For details on the lens shift feature, see “Step 2: Adjusting the Picture Position.”

(1 page 20)

Positioning the Projector and a screen

Screen

*

**

17

Connections and Preparations

When using the 16:9 aspect ratio screen size

Unit: mm (inches)

To calculate the installation positions

L (minimum) = 31.1781 (1

1

/

4

) × SS – 46.1543 (1

7

/

8

)

L (maximum) = 47.0644 (1

7

/

8

) × SS – 42.3308 (1

3

/

4

)

y = –1.598 × x (mm or inch) + 8.8414 (

3

/

8

) × SS

Screen Size

SS (inches)

40 60 80 100 120 150 200 250 300

(mm) 1016 1524 2032 2540 3048 3810 5080 6350 7620

L

minimum 1201 1825 2448 3072 3695 4631 6189 7748 9307

(47

3

/

8

) (71

7

/

8

) (96

1

/

2

) (121) (145

1

/

2

) (182

3

/

8

) (243

3

/

4

) (305

1

/

8

) (366

1

/

2

)

maximum 1840 2782 3723 4664 5605 7017 9371 11724 14077

(72

1

/

2

) (109

5

/

8

) (146

5

/

8

) (183

3

/

4

) (220

3

/

4

) (276

3

/

8

) (369) (461

5

/

8

) (554

1

/

4

)

x 000000000

(0) (0) (0) (0) (0) (0) (0) (0) (0)

y 354 530 707 884 1061 1326 1768 2210 2652

(14) (21) (27

7

/

8

) (34

7

/

8

) (41

7

/

8

) (52

1

/

4

) (69

5

/

8

)(87

1

/

8

) (104

1

/

2

)

x 44 66 89 111 133 166 221 277 332

(1

3

/

4

)(2

5

/

8

)(3

1

/

2

)(4

3

/

8

)(5

1

/

4

)(6

5

/

8

)(8

3

/

4

) (11) (13

1

/

8

)

y 283 424 566 707 849 1061 1415 1768 2122

(11

1

/

4

) (16

3

/

4

)(22

3

/

8

) (27

7

/

8

) (33

1

/

2

) (41

7

/

8

) (55

3

/

4

)(69

5

/

8

) (83

5

/

8

)

x 89 133 177 221 266 332 443 553 664

(3

1

/

2

)(5

1

/

4

) (7) (8

3

/

4

) (10

1

/

2

) (13

1

/

8

) (17

1

/

2

)(21

7

/

8

) (26

1

/

4

)

y 212 318 424 530 637 796 1061 1326 1591

(8

3

/

8

) (12

5

/

8

)(16

3

/

4

) (21) (25

1

/

8

) (31

3

/

8

) (41

7

/

8

)(52

1

/

4

) (62

3

/

4

)

x 133 199 266 332 398 498 664 830 996

(5

1

/

4

)(7

7

/

8

)(10

1

/

2

) (13

1

/

8

) (15

3

/

4

) (19

5

/

8

) (26

1

/

4

)(32

3

/

4

) (39

1

/

4

)

y 141 212 283 354 424 530 707 884 1061

(5

5

/

8

)(8

3

/

8

)(11

1

/

4

) (14) (16

3

/

4

) (21) (27

7

/

8

)(34

7

/

8

) (41

7

/

8

)

x 177 266 354 443 531 664 886 1107 1328

(7) (10

1

/

2

) (14) (17

1

/

2

)(21)(26

1

/

4

) (34

7

/

8

)(43

5

/

8

) (52

3

/

8

)

y 71 106 141 177 212 265 354 442 530

(2

7

/

8

)(4

1

/

4

)(5

5

/

8

)(7)(8

3

/

8

) (10

1

/

2

) (14) (17

1

/

2

) (21)

x 221 332 443 553 664 830 1107 1384 1660

(8

3

/

4

) (13

1

/

8

)(17

1

/

2

) (21

7

/

8

) (26

1

/

4

) (32

3

/

4

) (43

5

/

8

)(54

1

/

2

) (65

3

/

8

)

y 000000000

(0) (0) (0) (0) (0) (0) (0) (0) (0)

18

When using the 4:3 aspect ratio screen size

Unit: mm (inches)

To calculate the installation positions

L (minimum) = 38.1569 (1

1

/

2

) × SS – 46.1543 (1

7

/

8

)

L (maximum) = 57.5992 (2

3

/

8

) × SS – 42.3308 (1

3

/

4

)

y = –1.598 × x (mm or inch) + 10.8204 (

1

/

2

) × SS

Screen Size

SS (inches)

40 60 80 100 120 150 200 250 300

(mm) 1016 1524 2032 2540 3048 3810 5080 6350 7620

L

minimum 1480 2243 3006 3770 4533 5677 7585 9493 11401

(58

3

/

8

) (88

3

/

8

) (118

3

/

8

) (148

1

/

2

) (178

1

/

2

) (223

5

/

8

) (298

3

/

4

) (373

3

/

4

) (448

7

/

8

)

maximum 2262 3414 4566 5718 6870 8598 11478 14357 17237

(89

1

/

8

) (134

1

/

2

) (179

3

/

4

) (225

1

/

8

) (270

1

/

2

) (338

1

/

2

) (451

7

/

8

) (565

3

/

8

) (678

3

/

4

)

x 000000000

(0) (0) (0) (0) (0) (0) (0) (0) (0)

y 433 649 866 1082 1298 1623 2164 2705 3246

(17

1

/

8

)(25

5

/

8

) (34

1

/

8

) (42

5

/

8

) (51

1

/

8

) (64) (85

1

/

4

) (106

1

/

2

) (127

7

/

8

)

x 54 81 108 135 163 203 271 339 406

(2

1

/

4

)(3

1

/

4

)(4

3

/

8

)(5

3

/

8

)(6

1

/

2

) (8) (10

3

/

4

) (13

3

/

8

) (16)

y 346 519 693 866 1039 1298 1731 2164 2597

(13

3

/

4

)(20

1

/

2

) (27

3

/

8

) (34

1

/

8

)(41)(51

1

/

8

) (68

1

/

4

) (85

1

/

4

) (102

1

/

4

)

x 108 163 217 271 325 406 542 677 813

(4

3

/

8

)(6

1

/

2

)(8

5

/

8

) (10

3

/

4

) (12

7

/

8

) (16) (21

3

/

8

) (26

3

/

4

) (32)

y 260 390 519 649 779 974 1298 1623 1948

(10

1

/

4

)(15

3

/

8

) (20

1

/

2

) (25

5

/

8

) (30

3

/

4

)(38

3

/

8

) (51

1

/

8

)(64)(76

3

/

4

)

x 163 244 325 406 488 610 813 1016 1219

(6

1

/

2

)(9

5

/

8

) (12

7

/

8

)(16)(19

1

/

4

) (24) (32) (40) (48)

y 173 260 346 433 519 649 866 1082 1298

(6

7

/

8

)(10

1

/

4

) (13

3

/

4

) (17

1

/

8

) (20

1

/

2

)(25

5

/

8

) (34

1

/

8

) (42

5

/

8

) (51

1

/

8

)

x 217 325 433 542 650 813 1084 1355 1626

(8

5

/

8

)(12

7

/

8

) (17

1

/

8

) (21

3

/

8

) (25

5

/

8

) (32) (42

3

/

4

) (53

3

/

8

) (64)

y 87 130 173 216 260 325 433 541 649

(3

1

/

2

)(5

1

/

8

)(6

7

/

8

)(8

5

/

8

) (10

1

/

4

)(12

7

/

8

) (17

1

/

8

) (21

3

/

8

) (25

5

/

8

)

x 271 406 542 677 813 1016 1355 1693 2032

(10

3

/

4

) (16) (21

3

/

8

) (26

3

/

4

) (32) (40) (53

3

/

8

) (66

3

/

4

) (80)

y 000000000

(0) (0) (0) (0) (0) (0) (0) (0) (0)

19

Connections and Preparations

2 Position the projector so that the lens is parallel to the screen.

3 Project an image on the screen and adjust the picture so that it fits the

screen. (1 page 20)

When using a screen with an uneven surface, stripes pattern may rarely appear on the screen

depending on the distance between the screen and the projector or the zooming magnifications. This

is not a malfunction of the projector.

Note

Screen

Top view

20

Step 2: Adjusting the Picture Position

Project an image on the screen and then adjust the picture position.

Tip

The ?/1 (ON/STANDBY), INPUT, MENU, and M/m/</,/ (joystick) buttons on the side

panel of the projector function the same as those on the remote control.

Depending on the installation location of the projector, you may not control it with the remote

control. In this case, point the remote control to the screen instead of the projector.

Note

1 After connecting the AC cord to

the projector plug the AC cord

into a wall outlet.

The ON/STANDBY indicator lights

in red and the projector goes into

standby mode.

ON/STANDBY indicator

Remote control

detector

3 PATTERN button

5, 6

Zoom lever,

Focus ring

2

1

4

Lens shift dials

?/1 (On/

standby)

switch

Lights in red.

Page is loading ...

Sony VPL-HW50ES User manual

Sony VPL-HW50ES User manual

Related papers

Other documents