Sanus WSIWP1 Installation guide

Brand: Sanus

Model: WSIWP1

Type: Installation guide

Verify Speaker Plug Fit

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ ENTIRE MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS

CAUTION: Avoid potential personal injuries and property damage!

● Please read through these instructions completely to be sure you’re comfortable with this easy install process.

● Do not use this product for any purpose not explicitly specified by manufacturer.

● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

● If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product,

contact Customer Service

Tools Required

Tape Measure

This product conforms to and should be properly grounded in compliance with requirements of the current National Electrical Code or

codes administered by local authorities.

All electrical products may present a possible shock or ﬁre hazard if improperly installed or used. This product may bear the mark of a

Nationally Recognized Testing Laboratory and should be installed in conformance with current local and/or the National Electrical Code.

WARNING: RISK OF FIRE AND SHOCK. Do not connect the modules

to any other circuits or outlets.

CAUTION: RISK OF FIRE AND SHOCK. ONLY intended for use on 15 ampere branch circuits.

CAUTION: RISK OF FIRE AND SHOCK. Do not install power supply cord

within wall cavity.

Pencil Phillips Screwdriver

Paint (optional)

Surfaces are paintable

to match your decor

Electric Drill

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not

return the damaged item to your dealer; contact Customer Service. Never use damaged parts!

MAX

1 ⅛ in. (29 mm)

BEFORE DRILLING ANY HOLES:

Make sure your speaker plug ﬁts in

the upper module

Verify Wall Compatibility

Legrand AV Inc. and its aliated corporations and subsidiaries (collectively, “Legrand”), intend to make this manual accurate and complete. However, Legrand makes no claim that the

information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The

information contained in this document is subject to change without notice or obligation of any kind. Legrand makes no representation of warranty, expressed or implied, regarding the

information contained herein. Legrand assumes no responsibility for accuracy, completeness or suciency of the information contained in this document.

Legrand AV INC. 6436 City West Parkway; Eden Prairie, MN 55344 USA

STEP 1

Upper Module

Driver Bit

(hole saw)

Hole Saw

3 in.

Lower Module

Power Supply Cord

Assemble the

Hole Saw

Drill Holes

TIP: Drill the top hole on the

less visible side, of your speaker.

Maximum Distance: 6 feet

Maximum

Height:

10 feet

1025682 03/20

Model WSIWP1-W1

OWNERS GUIDE

IN-WALL CABLE KIT

Before getting started, let’s make sure this product is perfect for you!

Included

Supplied Parts

This Cable Kit is designed to ﬁt into both interior

and exterior walls constructed with:

Minimum Space into Wall: 3 in.

Minimum Drywall Thickness: 1/2 in. (MAX: 1 in.)

No Fire Block Stud in the cavity *

NOTE:

The cable Pass-

Through Width is

1.75 inch.

Walls with blown-

in type insulation

may require

removal of some

insulation inside

the cavity.

Drywall

Stud

Back Wall

We’ll Make It Stress-Free

If you have any questions along the way, just give us a call.

800-359-5520 or, chat at SANUS.com/chatSP

We’re ready to help!

* A horizontal ﬁre block stud requires a 1.75 inch hole to pass the power cord.

This requires removal, then repair of drywall, to gain access to that stud.

We recommend you consult a professional.

STEP 5

Plug In Cables

Insert Modules in Wall Secure Modules

STEP 3 STEP 4STEP 2

Route Cables

REMOVAL

Speaker

Plug

Standard Outlet

Speaker

Power Cord

Remove

trim plate

Turn screws to

remove module

Loosen ONLY enough

to remove module.

Unplug

power cords

Low Voltage Cable(s)

DO NOT over tighten screws

NOTE: The gaskets can be

removed for larger cables.

DO NOT loosen

the screws

TIP: Use a ﬁsh

tape, to pull the cables

through the wall.

Replace Trim

Plate

Replace Trim

Plate

Remove

Trim Plate

Remove

Trim Plate

Low Voltage

Cable(s)

[if needed]

Sanus WSIWP1 Installation guide

Sanus WSIWP1 Installation guide

Sanus WSIWP1 Installation guide

Related papers

Other documents