Comelit KAE5062 Technical Manual

Comelit
Brand
Comelit
Model
KAE5062
Category
Telephones
Type
Technical Manual
EN
TECHNICAL
MANUAL
Technical manual for two-family Kit Art. KAE5062
2
Warning
• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the
standards in force. Do not tamper with the internal elements offering protection against short circuits and overcurrents.
• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any
responsibility for improper use of the apparatus, for any alterations made by others for any reason or for the use of
non-original accessories or materials.
• All the products comply with the requirements of the 2014/30/EU and 2014/35/EU directives. This is proved by the
CE mark on the products themselves.
• Do not route the riser wires in proximity to power supply cables (230/400V).
• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised
electricians.
• Do not press and hold the audio hook while the handset is lifted.
• Disconnect the power supply before carrying out any maintenance procedures.
• The electrical system of the building must be fitted with an omnipolar mains switch with a contact opening of at least
3 mm, which is capable of isolating the power supply of the device.
• Place the protection back over the terminals and close the inspection door after every procedure.
Table of contents
Warning ............................................................................................ 2
Package Contents ........................................................................... 3
Transformer Art. 1200...................................................................... 4
Description ...............................................................................................4
External unit Art. ET5002 ................................................................ 5
Description ...............................................................................................5
Installation ................................................................................................6
Replacing the nameplate holders .......................................................6
Internal unit Art. 2701W................................................................... 7
Description ...............................................................................................7
Installation ................................................................................................8
Operating distances and standard diagram ................................. 9
Wiring diagram for standard system and 1 additional door-entry phone
connection variant ...................................................................................9
Operating distances ................................................................................. 9
3
Package Contents
This manual includes information regarding system configuration and customisation which may be perceived as necessary by
the installer.
2701W 2701W1200
ET5002
KAE5062
×1 ×1 ×
1
ET5002 - External unit
×2
2701W - Telephone
×1
1200 - Transformer
3
1
6
4
12 V~
230 V~
1.
2.
4
Transformer with 230V primary, 12V AC / 15 VA secondary winding for continuous use. Dimensions: 53x95x65 mm (3 DIN
modules).
1. 230 V digital input.
2. Secondary 12 V AC output.
Disconnect the power supply before carrying out any maintenance procedures.
The electrical system of the building must be fitted with an omnipolar mains switch with a contact opening
of at least 3 mm, which is capable of isolating the power supply of the device.
Place the protection back over the terminals and close the inspection door after every procedure.
Transformer Art. 1200
Description
1.
2
3.
4.
5.
6.
7.
10.
9.
8.
5
External unit Art. ET5002
Description
External unit complete with 2 call buttons, 1 wall bracket and 1 flush-mounted box.
Dimensions 95×135×26.5 mm (including wall bracket).
1. Surface-mounted wall bracket Art. ET9160. A flush-mounted box Art. ET9150 is also available.
2. Stainless steel front faceplate.
3. Faceplate fixing screw holes.
4. Speaker.
5. Call buttons.
6. Microphone.
7. Speaker.
8. Terminal block for connection:
S2 S1 Electronic call signal output
4 Negative
3 Loudspeaker input
2 Microphone output
~~* 12V AC power supply terminals
9. TM2 Microphone volume adjustment trimmer.
10. TM1 Loudspeaker volume adjustment trimmer.
2
1
2
1
2
3
321
9,5 cm
13,5 cm
21
1
ET9160
2
CH2
2
3
1
5A4A3A
2
1
ET9150
CH2
2
3
1
5B4B3B
6
Installation
Replacing the nameplate holders
2.
1.
5.
6.
3.
4.
7
Internal unit Art. 2701W
Description
Audio internal unit complete with 1 key button. Dimensions 105×190×28 mm.
1. Handset.
2. Key button.
3. Speaker.
4. Audio hook.
5. Terminal block:
S Electronic call signal input
2 Loudspeaker input
3 Microphone output
4 Negative
P1 Terminal for key button
6. Handset connector.
2
1
3
2
1
3
2
1
3D3C3B
max 7 cm
1
1
CLACK!
2
CLACK!
1
1
1
1
2
654
2
1
160 cm
130 cm
1
2
3
3A21
mm 190
mm 105
7
8
Installation
S 2 3 4
P
1
S 2 3 4
P
1
120
0
~
S2
S1
4
3
2
~
~
*
*
2701W2701W
ET5002
12V~
230V~
1
P
2 3 4S
2701W
1
P
2 3 4S
2701W
Local lock release button.
EK5/02S
9
1 mm²
1,5 mm²
1,5 mm²
200 m 200 m 80 m
0,8 mm²
1 mm²
1 mm²
150 m 150 m 30 m
0,5 mm²
0,8 mm²
0,8 mm²
50 m 50 m 10 m
Operating distances and standard diagram
Wiring diagram for standard system and 1 additional door-entry phone connection
variant
Operating distances
www.comelitgroup.com
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
1 ed. Rev.1 12/2016
cod. 2G40001773
CERTIFIED MANAGEMENT SYSTEMS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Comelit KAE5062 Technical Manual

Comelit
Brand
Comelit
Model
KAE5062
Category
Telephones
Type
Technical Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents