Wildix W24FXS Quick Installation Manual

Wildix
Brand
Wildix
Model
W24FXS
Category
Networking
Type
Quick Installation Manual

Wildix W24FXS is a media gateway that allows you to connect analog devices to a VoIP network. It has 24 ports for connecting analog phones or other devices, and it can be configured to use either a static IP address or DHCP. The gateway also has a built-in web interface that allows you to manage its settings and view its status.

The Wildix W24FXS is a versatile device that can be used in a variety of applications. For example, it can be used to connect analog phones to a VoIP PBX, or it can be used to add analog ports to an existing VoIP network. The gateway is also compatible with a variety of SIP-based IP PBXs, making it a flexible solution for businesses of all sizes.

Wildix W24FXS is a media gateway that allows you to connect analog devices to a VoIP network. It has 24 ports for connecting analog phones or other devices, and it can be configured to use either a static IP address or DHCP. The gateway also has a built-in web interface that allows you to manage its settings and view its status.

The Wildix W24FXS is a versatile device that can be used in a variety of applications. For example, it can be used to connect analog phones to a VoIP PBX, or it can be used to add analog ports to an existing VoIP network. The gateway is also compatible with a variety of SIP-based IP PBXs, making it a flexible solution for businesses of all sizes.

Wildix W24FXS 2015 Media gateway
Version: 28.07.2015
Quick Installation Guide
The steps below help you to connect and configure the gateway
1. Overview and LED indications 3
2. Connection to power supply 3
3. Connection to the network 3
3. Connection of analog phones 4
4. Configuration of the gateway 4
5. Reset of the gateway 4
Wildix W24FXS 2015 media gateway - Quick Installation Guide 2
1. Overview and LED indications
Rear panel
•
ON/OFF Switch
•
Power supply jack AC 110V~240V, 50-60Hz
•
RJ21 Port for patch panel connection
Front panel
•
1 WAN port RJ45 10/100 base-T
•
1 Console port RJ45 with RS232 standard to connect DB9
•
1 RST switch to perform the factory reset
•
1 PWR LED:
-
solid green indicates that the gateway is powered on
•
1 RUN LED:
-
turns solid green for a few seconds once the gateway is powered on;
-
fast blinking indicates that all ports are registered successfully
-
slow blinking indicates that ports failed to register
-
off (when connected to power) indicates that the gateway doesn’t boot up
•
1-24 ports for connection of analog devices
•
1-24 LEDs:
-
solid green indicates that the port is in use
-
off (when connected to power) indicates that the port is idle
2. Connection to power supply
1) Connect the gateway to the Power Supply using the cable provided
2) Turn the switch situated on the rear panel into “ON” position
3. Connection to the network
1) Connect the gateway’s WAN port to Wildix Switch using Ethernet cable
2) By default the gateway is set up with the static IP address, please follow this guide to
change the mode to DHCP client.
Notes
•
the gateway should be connected via Ethernet cable to the same network as the PBX or an
external DHCP server (for instance its Router)
•
as soon as the DHCP server assigns an IP address to the gateway, you can pass to the next
step of the gateway configuration
•
In case the PBX is used as a DHCP server, the gateway is detected on the network
automatically
•
In case an external DHCP server is used, check the list of the active leases to detect the IP
address assigned to the gateway
Wildix W24FXS 2015 media gateway - Quick Installation Guide 3
3. Connection of analog phones
•
You can connect analog devices directly to ports marked 1-24
•
Otherwise connect the patch panel to the RJ21 port situated on the rear panel using the
connector provided.
4. Configuration of the gateway
•
Follow our online guide to provision the media gateway
For remote/unreachable media gateways behind NAT/Firewall, follow our online guide to
remote provisioning.
• Follow our online guide to assign the ports of the media gateway
5. Reset of the gateway
The switch marked as “RST” is situated on the front panel of the gateway.
1)
use the paper clip or the object of the similar shape to press the button
2)
hold the button pressed for more than 7 seconds to restore the gateway to the factory
settings.
3)
reboot the gateway for the changes to take the effect
Note: keep the button pressed for just 3-5 seconds, to restore the default IP and user name /
password (in this case all the other configurations are kept); it is necessary to reboot the
Wildix W24FXS 2015 media gateway - Quick Installation Guide 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Wildix W24FXS Quick Installation Manual

Wildix
Brand
Wildix
Model
W24FXS
Category
Networking
Type
Quick Installation Manual

Wildix W24FXS is a media gateway that allows you to connect analog devices to a VoIP network. It has 24 ports for connecting analog phones or other devices, and it can be configured to use either a static IP address or DHCP. The gateway also has a built-in web interface that allows you to manage its settings and view its status.

The Wildix W24FXS is a versatile device that can be used in a variety of applications. For example, it can be used to connect analog phones to a VoIP PBX, or it can be used to add analog ports to an existing VoIP network. The gateway is also compatible with a variety of SIP-based IP PBXs, making it a flexible solution for businesses of all sizes.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents