Wildix DaySaver Quick Installation Manual

Brand: Wildix

Model: DaySaver

Type: Quick Installation Manual

DaySaver Quick Installation Guide

Page 2 of 15

1 - SIM slot: insert and press a SIM card to the slot

2 - SIM LED indicator: shows SIM registration status

3 - LAN LED indicator

4 - Running indicator: indicates network registration status

5 - Power indicator: shows power supply status

6 - WAN LED indicator

7 - 2 antennas: one for data connections; another one - for calls and SMS

:Rear panel

DaySaver Quick Installation Guide

Page 3 of 15

1 - DC 12V power supply (optional, WMP code: PS-12V2A)

2 - WAN/ PoE port

3 - LAN port (static IP address 192.168.11.1)

4 - buttonReset

5 - buttonReboot

LED indicators description

Indicator State Description

PWR Off There is no power supply or it is abnormal

On The device is powered on

RUN Off The device is not running normally

On The device is being initialized

Slow flashing The device is successfully initialized and running normally

WAN/

LAN

Off The is no network connection

Fast flashing Network is successfully connected

SIM

Slow flashing 4

sec

SIM card cannot be detected (flashing ever 4 seconds)

Fast flashing SIM card has been inserted and successfully registered (flashing every 2

seconds)

DaySaver Quick Installation Guide

Page 4 of 15

Installation and connection

Make sure the PIN code of the SIM card is disabled.

Connect antennas to the rear panel of the gateway

Connect network cable to WAN/ PoE port

Insert a SIM card to the slot

Provisioning and configuration

For provisioning of DaySaver, consult .Provisioning of Wildix devices Guide

For remote/unreachable media gateways behind NAT/ Firewall, follow Remote Provisioning of Wildix devices

.Manual

After provisioning, the gateway appears in WMS:

WMS -> :Devices

WMS -> Trunks:

The number of supported devices per one system:

For making calls: no limit

For sending SMS: no limit starting from WMS v. 4.03.44914.04

Note for WMS Network: the option "Remote PBX (for SMS sending)" in WMS -> ->Settings System FAX

doesn't work if another DaySaver is registered to one of the PBXs./SMS server

Note: Auto-upgrade process can take up to 5 minutes. During the upgrade, a device downloads a new

firmware, receives a password and SIP registration.

Please DO NOT reset the device during the upgrade procedure:

Important: Status of signal quality is currently not supported!

DaySaver Quick Installation Guide

Page 5 of 15

After the device is provisioned, you can configure its settings. Consult Trunk Settings Guide to check all available

parameters.

Data connection backup

How does it work?

DaySaver is your small remote office. It can work as a data connection backup, in case if your Internet goes

down, and as a backup for Cloud PBX. And, same as its predecessor, it provides phone calls and SMS even if

your operator becomes unreachable (since it allows you placing calls via Mobile network).

DaySaver keeps monitoring the PBX and a other hosts and in case they become unreachable, it automatically

switches to mobile data (4G connection). The gateway supports speeds up to 100 Mbit in download and 50 Mbit

in upload.

: DaySaver is placed between the customer’s existing network and a separate VoIP Backup for the voice service

Network (over vlan, for example). If the PBX becomes unreachable over network, DaySaver automatically

switches the connectivity to 4G / LTE.

Without DaySaver:

With DaySaver:

DaySaver Quick Installation Guide

Page 6 of 15

: DaySaver is placed between the router and the whole network of the customer. In Backup for an entire office

case the office internet connection goes down, all traffic starts working via DaySaver:

Enable VoLTE

VoLTE Network allows using DaySaver as a backup for Cloud PBXs, as a backup for the cable Internet

connection, or, even as the only Internet access for small offices or during the events.

To activate VoLTE, proceed with the following steps:

Go to -> Network VoLTE

Check off in Status fieldEnable

Click Save

Confirm by clicking Apply

Set uplink config

DaySaver Quick Installation Guide

Page 7 of 15

The uplink config should be set to " " with tracking IP addresses set to something WAN Master, VoLTE Slave

publicly accessible, in this example we use 8.8.8.8.

Go to -> Network Uplink Config

Set WAN Master,VoLTE Slave

Click Save

If WAN loses 3 pings to 8.8.8.8, it failovers to VoLTE. When WAN becomes available again (Count of up), WAN

becomes the master again.

Enable DHCP Server

Go to -> rNetwork DHCP Serve

Check off Enable

DHCP Server settings must have default gateway as the DaySaver LAN IP address

DNS Servers must be reachable via LAN

Note: Enable DHCP Server to use DaySaver as a backup for an entire office. All other DHCP servers

connected to a network switch should be disabled.

DaySaver Quick Installation Guide

Page 8 of 15

If you want to use DaySaver as a backup for a single switch:

Connect WAN into Existing Network / Router (DHCP Client)

Connect LAN into Switch that powers phones

Set Static IP Address for WAN port

Go to Network -> Setting

Plug WAN & LAN port into existing Switch / Router

Allow devices on existing network to get IP addresses from DHCP Server provided from DaySaver:

Important: If you do not connect DaySaver via WAN port to a router, you must assign a static IP to it.

Otherwise the port will be assigned to 0.0.0.0 IP address and DaySaver won't be registered to a PBX

through LTE.

Before setting Static IP, disable DHCP server on existing network.

DaySaver Quick Installation Guide

Page 9 of 15

Status Page Example

Go to ->Status Overview

Check the network status:

Test the network topology

To test the network topology, you can use some of the following tools:

1. Tracert

DaySaver Quick Installation Guide

Page 11 of 15

Once the device is provisioned, assign Dialplan procedure to DaySaver. This can be done in WMS -> main

Trunks -> GSM/UMTS -> trunk settings:Edit

Configure a number you want to use in the procedure. This is the number to be used for routing your main

calls from DaySaver to your applications. In the example, 6000 is used:

Once the above has been completed, access DaySaver and edit VoLTE trunk settings: go to -> Trunk

and change and to the number you have applied to procedure: VoLTE Extension Autodial Number main

Once you have saved and applied all settings, you are able to call the mobile number associated with the

SIM card which will hit the PBX

In order to achieve this goal, an activated SIM card is required. This method works with 2G and above.

DaySaver Quick Installation Guide

Page 12 of 15

How to send/ receive SMS

Consult for detailed description of how to send and receive SMS.FAX/ SMS Server Quick Guide

Time indexes of SMS sending

10 sms -> 1.20 min

20 sms-> 2.20 min

30 sms -> 3.20 min

40 sms -> 4.20 min

50 sms -> 5.20 min

60 sms -> 6.20 min

70 sms -> 7.20 min

80 sms -> 8.20 min

90 sms -> 9.20 min

100 sms -> 10.20 min

Factory reset and reboot

To perform a factory reset procedure for restoring default settings:

Press and hold Reset button for 10 seconds

To reboot the device:

Press and hold button for 10 secondsReboot

Recovery

In order to recover DaySaver, the following steps are required before proceeding:

PoE connectivity

Requirements:

WMS 5.0X/ WMS 4.0X

DaySaver firmware version 2.53.4.20 or higher

Starting from WMS v. 4.03.44914.04, it is possible to select a specific DaySaver for each user by editing

a config file. Consult for detailed configuration.Custom config parameters List

The reset procedure is identified by changes of RUN indicator: slow flashings turn into fast

flashings. When the indicator becomes solid green, it means that DaySaver is reset.

Important: complete initialization and loading can take up to 5 minutes!

DaySaver Quick Installation Guide

Page 13 of 15

2 x RJ45 cables

Latest firmware version ( to download the file)LINK

Laptop / Machine

Step 1

Hold and press both and buttons, power up the device via WAN/ PoE andReset Reboot keep holding the

when plugging in. This will put the device into recovery: for 30 secondstwo buttons

Step 2

Run a cable between the LAN port and your laptop/ machine ensuring the DaySaver is still powered up

Note: If you machine uses Wi-Fi, please disable it as this prevents you browse to the recovery

interface (192.168.11.1).

DaySaver Quick Installation Guide

Page 14 of 15

Step 3

Once connected, you are be able to browse to the recovery interface “192.168.11.1” and upload the

firmware file

Click Choose file and select the firmware version from your machine

Click Upload, then wait 10 - 15 minutes for this process to be completed

Step 4

Remove the LAN cable, ensuring the WAN cable is still connected and reboot

The recovery is completed. You are now be able to use the device and browse IP to provision

DaySaver Quick Installation Guide

Page 15 of 15

Wildix DaySaver Quick Installation Manual

Wildix DaySaver Quick Installation Manual

Wildix DaySaver Quick Installation Manual

Related papers

Other documents