Angler LEDSB-1818 Instructions Manual

Brand
Angler
Model
LEDSB-1818
Type
Instructions Manual
INSTRUCTIONS
Collapsible LED Softbox
LEDSB-1818
For 1 × 1 LED Lights
2
Overview
Corner straps
Securing straps
Adjustable corners
Diuser
Recessed touch-connect strip
Carry bag
Notches
3
Attaching the Softbox
Preparing the Light Fixture
If the fixture has height adjustment knobs, raise the fixture’s height
so it sits above the bottom of the yoke.
Some 1 × 1 fixtures have two sets of side knobs for tilt and height
adjustment. Adjust the height so the tilt knobs are in the middle of
the fixture. This will make it easier to fit the softbox onto it.
Tip: Tilting the fixture upward in its yoke will make it easier to fit the
softbox onto the fixture.
Attaching the Softbox
1.
Open the adjustable corners held
together with straps and touch-
connect strips.
2.
Align the softbox with a 1 × 1 light so
the securing straps don’t interfere
with the light’s rear control panel.
Note: For Luxli’s Timpani, the securing straps should be on the
sides of the fixture, the buckles should be on the right, and the
strap that’s closest to the edge of the softbox is on top.
1
4
3.
Fit the top of the softbox over the
fixture’s top rim, and attach the
upper strap across the back of the
light.
4.
Fit the bottom of the softbox over
the fixture’s bottom rim, and attach
the lower strap.
5.
Fit the corners over the fixture, and
close the adjustable corners so the
fit is snug.
6.
Secure the adjustable corners with
the corner straps.
3
4
5
6
5
Adding the Diuser
Attach the diffuser to the innermost
edge of the recessed touch-connect
strip . Make sure to leave enough room
for a grid.
Angler LEDSBG-1818 LED Grid for the LEDSB-1818 Softbox
(sold separately)
The accessory grid narrows the beam
spread and controls light spill. Attach
the accessory grid to the recessed touch-
connect strip on the front inner edge of
the softbox.
6
Warnings
Please read and follow these instructions, and keep this
manual in a safe place.
For use only with LED fixtures.
Use caution when unfolding this product. Unfold in an area
large enough to accommodate the full size of the softbox.
Do not unfold around breakable objects.
Do not machine wash.
All photos are for illustrative purposes only.
SPECIFICATIONS
Material Side and rear panels:
Polyester
Inner panels:
Silver-coated polyester
Diffuser: Polyester
Dimensions (W × H × D) 18 × 18 × 12.75 in.
(45.7 × 45.7 × 32.4 cm)
LED Opening (W × H) 12 × 12 in. (30.5 × 30.5 cm)
Weight 16.3 oz. (463 g)
7
One-Year Limited Warranty
This Angler product is warranted to the original purchaser to be free from defects in materials and
workmanship under normal consumer use for a period of one (1) year from the original purchase date
or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s
discretion, of any product that fails during normal use of this product in its intended manner and in
its intended environment. Inoperability of the product or part(s) shall be determined by the warranty
provider. If the product has been discontinued, the warranty provider reserves the right to replace it
with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you
with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Angler Customer Service Department to obtain a return
merchandise authorization (“RMA”) number, and return the defective product to Angler along with
the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own
risk and expense.
For more information or to arrange service, visit www.anglerlights.com or call Customer Service at
212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
Angler is a registered trademark of the Gradus Group.
© 2019 Gradus Group LLC. All Rights Reserved.
ANGLER
A Gradus Group
Brand
GG2
anglerlights.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Angler LEDSB-1818 Instructions Manual

Brand
Angler
Model
LEDSB-1818
Type
Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents