JAPANESE
GERMAN FRENCH ITALIAN SPANISHENGLISH
SPEAKER STAND TD508 speaker only
Thank you for purchasing this high quality speaker stand. Please read this installation manual before assembling
the stand, and be sure to use it properly. An accident or injury can result if the stand is incorrectly assembled or
unspecified parts are used. After assembly, keep this manual where it can be consulted when necessary.
Contents
Contents
Included Parts 2
Cautions before use 3
Using this product safely and properly 3
Routing speaker wire 7
Before
installation
Installation
Assembling the speaker stand 5
Speaker angle adjustment 7
Removing the speakers 4
SPEAKER STAND TD510 speaker only
OWNER’S MANUAL
-
2
-
JAPANESE
ENGLISH GERMAN FRENCH ITALIAN SPANISH
D3 components
Joint
X1
1
Post
X1
2
Base plate
X1
3
Hexagonal bolt
X2
4
Spike hole seal
X5
7
Foot
X5
8
Pan-head bolt
X1
5
Allen key
X1
6
Included P
Included P
ar
ar
ts
ts
Check that all of the following components are present
Check that all of the following components are present
D6 components
Joint
X1
1
Post
X1
2
Base plate
X1
3
Screw (binding)
X2
4
Spike (M8X25)
X5
7
Hexagonal nut
X5
8
Pan-head bolt
X2
5
Allen key
X1
6
Insulator
X5
9
-
3
-
••
This stand is meant for use with the TD508 speaker or
TD510 speaker. Do not use the stand for other purposes.
Improper use of the stand can result in an unstable
condition with the potential to cause an injury by falling.
••
Assemble the stand on a level surface. Placing the stand
on an uneven surface can lead to overturning and result
in an injury.
••
Do not place the stand where people regularly move past
it. Bumping into the stand can cause an injury.
••
Place the stand on a solid and level floor. Installing the
stand in a location that is unstable can cause it to fall and
result in an injury.
Using this product saf
Using this product saf
ely and proper
ely and proper
ly
ly
••
Do not place this stand on a tall object or high shelf. If the stand were to fall, it could cause an injury.
••
Do not drop or drag the stand when assembling or
transporting it. Pushing over or dragging the stand can
result in an injury or cause damage to the floor.
••
Do not climb onto or hang from the stand. Be especially
careful about children trying to do this. If the stand falls
over it can cause an injury.
••
The stand is heavy, so be sure 2 or more people
cooperate in unpacking or moving it. Improper lifting can
cause a back injury and dropping the stand can injure
feet.
••
This is a stand for a speaker system. Avoid using the stand for other purposes.
••
The stand is very heavy. Use caution when handling it.
••
Be careful not to tip over the stand.
••
Be careful that the speaker system does not fall from the stand.
••
If the stand becomes dirty, clean it by lightly wiping with a soft cloth having a neutral cleaning solution on it. Do not
use a substance like thinner or benzene.
Cautions bef
Cautions bef
ore use
ore use
JAPANESE
GERMAN FRENCH ITALIAN SPANISHENGLISH
The indicator symbols shown below are used in this manual and on the stand to ensure proper and safe use of the
product, prevent injuries and avoid damage to surrounding items. Please become familiar
with these symbols and their associated information before proceeding to the assembly instructions of this manual.
This "Warning" sign indicates a situation in which incorrect handling may result in death
or serious personal injury.
This "Caution" sign indicates a situation in which incorrect handling may result in
personal injury or may result solely in damage to property.
This section contains information that can help to prevent problems and damage to the
unit, and also contain other useful information.
Tip
Warning
Caution
Warning
Caution
-
4
-
JAPANESE
ENGLISH GERMAN FRENCH ITALIAN SPANISH
The speaker is heavy, so hold it with both hands when
removing it.
Speaker
Remove the angle adjustment screw and the washer.
3
Slide the speaker to the right and then lift it up to
remove it.
4
Screws
X4
Base cover
Speaker
Washer
Joint
Angle adjustment screw
Speaker
Speaker
Base bracket
Remove the base cover.
2
-
Removing the speakers
-
Remove the screws from the bottom of the speaker
base bracket.
1
Installation
Installation
-
5
-
-
Assembling the speaker stand (for D3 )
-
Install the base plate and the post with the pan-head
bolt.
1
Pan-head bolt
Hexagonal bolt
Speaker
Insert the Hexagonal bolt (speaker turn-prevention
bolts) into the joint.
2
Assemble the joint and the post with the Hexagonal
bolt.
3
Washer
Angle adjustment screw
Hexagonal bolt
(speaker turn-
prevention
bolts)
Post
Base plate
Joint1
2
3
4
5
4
JAPANESE
GERMAN FRENCH ITALIAN SPANISHENGLISH
Commercially-available spikes (M8) can also be
installed instead of the accessory spike hole seals and
feet.
5
••
The speaker is heavy, so lie it on the floor and place
your hands around it when installing it.
••
Lay a soft cloth or similar on the floor to prevent any
damage to the speaker and the floor while working.
Install the spike hole seals and feet into the spike
mounting holes in the base plate (5 places).
4
Commercially-available spikes (M8) can also be installed
instead of the accessory spike hole seals and feet.
Spike hole seal
7
Foot
8
Tip
Speaker Stand
-
6
-
JAPANESE
ENGLISH GERMAN FRENCH ITALIAN SPANISH
-
Assembling the speaker stand (for D6)
-
Install the base plate and the post with the pan-head
bolt.
1
2
Assemble the joint and the post with the Screw
(binding).
3
Speaker
Washer
Angle adjustment screw
Speaker Stand
Place the insulator under the base plate, and then
install the spikes and nuts to the base plate.
••
Turn the spikes clockwise one at a time. Once the end
of the spike feels as though it is touching the insulator,
secure with the nut.
Insert the speaker into the joint, adjust it to the
preferred angle, and then tighten the washer and
angle adjustment screw to secure it in that position.
4
••
The speaker is heavy, so lie it on the floor and place
your hands around it when installing it.
••
Lay a soft cloth or similar on the floor to prevent any
damage to the speaker and the floor while working.
Pan-head bolt
Screw (binding)
Post
Base plate
Joint1
2
3
5
4
Spike7
Insulator9
Insulator
9
Hexagonal nut8
Spike7
Tip
Hexagonal nut
8
-
7
-
JAPANESE
GERMAN FRENCH ITALIAN SPANISHENGLISH
-
Routing speaker wire
-
When connecting the speaker wire, connect it securely
so that the end of the speaker wire does not touch any
neighboring terminals.
1
Speaker Wire
-
Speaker angle adjustment
-
Loosen the angle adjustment screw on the right side of
the speaker.
1
Speaker
Slide the speaker to the right slightly to disengage the
tab of the joint.
2
Joint
Angle adjustment screw
Adjust the speaker to the desired angle.
3
1 forward step
Securely tighten the angle adjustment screw.
4
2 backward steps
••
Hold the speaker securely while adjusting the angle.
Speaker Wire
Allen key6
Tip
-
8
-
JAPANESE
ENGLISH GERMAN FRENCH ITALIAN SPANISH
/
