RAB Lighting RDLED4R12D-50YYHC-M-W Operating instructions

RDLED4 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding

is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A

PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

CEILING CUT OUT MUST BE FREE OF ANY DEBRIS AND BURRS.

FIXTURE MOUNTING

This xture can be installed with ceiling temperature not

exceeding of 40°C and with minimum plenum height of 5/”.

The xture can be used to replace an existing unit or for new

construction with non-accessible ceiling in place.

1. Prepare the mounting surface with cut out diameter 5”

for RDLED4R and 5”x5” for RDLED4S. Cut-out must be

accurate not undersized.

2. Remove the dust protector.

3. Loosen the Junction Box Screw and open the Junction

Box (Fig.1). Attach Supply Wires into Junction Box and

connect to the xture. See wiring section for details.

4. Push up and slide the Junction Box section into the

ceiling. Be sure the Mounting Flag is folded in as the

xture slides through ceiling hole. (Fig. 3)

5. For the Wallwash Model, orient the xture such that the

Reector is in correct orientation. Wall Wash xtures are

provided with swivel arm for maximum adjustability in all

construction situations. Look for ‘Towards the Wall’ label

on the xture. (Fig. 2)

6. To secure xture into ceiling, swing Mounting Flag

outward by turning Flag Screw clockwise. Ceiling

Flange should be snug tight against ceiling. DO NOT

OVERTIGHTEN SCREWS.

7. Insert dust protector to protect the LED & Reector until

Trim Assembly is ready to be installed.

RDLED4R RDLED4S

Cut-Out Diameter: 5” Cut-Out: 5”x5”

Supply wires

Fig: 1

Junction Box

Screw

Junction Box

Fig: 2

Mounting Flag

Flag Screw

Heat Sink

Ceiling Flange

Reector

Fig: 3

Flag Screws

RDLED4 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

TROUBLESHOOTING

1. Check that the line voltage at the xture is correct. Refer

to wiring directions.

2. Is the xture grounded properly?

3. For questions on compatibility of dimmers purchased

separately or existing dimmers, refer to

www.rabweb.com

4. If the LED is blinking the xture may be overheating.

Remove the Trim assembly and if the xture is labeled

‘BLINKING LIGHT OF THIS THERMALLY PROTECTED

LUMINAIRE MAY INDICATE OVERHEATING’ allow the

xture to cool down. Determine cause of overheating

and remove. Fixtures with this label have a thermal

protector that turns xture o above a certain

temperature. It will automatically restart when cool.

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool enough to

touch. Do not clean or maintain while xture is energized.

1. Do not open xture to clean the LED. Do not touch

the LED.

2. Do not touch reector, lens or trim cone.

3. Do not clean any xture surface with wood base cleaning

material such as paper towels or tissues. Only use micro

ber cleaning cloth.

Easy Installation & Product Help

Tech Help Line

Call our experts 888 RAB-1000

rthvale, New Jersey 07647 USA

rabweb.com

Visit our website for product info

Answered promptly sales@rabweb.com

RDLED4 IN-1214

Trim clip

opening

Trim Assembly

Trim Clip

TRIM ASSEMBLY MOUNTING

1. Check to ensure the Trim clip opening is free of debris

and paint.

2. Match the Trim Spring Clip to Spring Clip Opening and

snap the Trim Assembly into Trim clip opening. Trim

ring should be ush to ceiling as shown in Fig. 4.

3. For the Wallwash Model, aim the xture such that the

reector is in correct orientation. Look for ‘Towards the

Wall’ label on the reector.

Fig: 4

WIRING

RISK OF FIRE. Universal voltage driver permits operation at

120V thru 277V, 50 or 60 Hz. For Non-Dimming, Electronic

Low Voltage (ELV) and Triac Dimming follow the wiring

directions in Fig. 5.

1. Connect the GROUND wire from xture to supply ground.

2. Connect the black xture lead to the (+) LINE supply lead.

3. Connect the white xture lead to the (-) COMMON supply

lead.

Lutron L3D Hi-Lume series drivers work with Lutron 3-Wire

Control (Fig. 6) or EcoSystem Digital Controls (Fig. 7).

Note: See www.lutron.com for complete instructions and functional

compatibility of Lutron drivers with Lutron or other control systems/

dimmers.

Fig: 5

Fig: 6

Fig: 7

Note: These instructions do not cover all details or variations in

equipment nor do they provide for every possible situation during

installation, operation or maintenance. RAB cannot troubleshoot

Lutron systems and have provided only basic information. See

www.lutron.com for complete instructions and functional

compatibility of Lutron Drivers with Lutron or other Control systems/

dimmers.

RDLED4 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

Ø5.5”

4.6”

12.53”

4.0”

2.5”

4.65”

12.53”

4.0”

2.5”

5.51”

DIMENSIONAL DRAWING

RDLED4R

RDLED4S

RDLED6 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding

is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A

PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

CEILING CUT OUT MUST BE FREE OF ANY DEBRIS AND BURRS.

FIXTURE MOUNTING

This xture can be installed with ceiling temperature not

exceeding of 40°C and with minimum ceiling height of 5/”.

The xture can be used to replace an existing unit or for new

construction with non-accessible ceiling in place.

1. Prepare the mounting surface with cut out diameter 7”

for RDLED6R and 7”x7” for RDLED6S. Cut-out must be

accurate not undersized.

2. Remove the dust protector.

3. Loosen the Junction Box Screw and open the Junction

Box (Fig.1). Attach Supply Wires into Junction Box and

connect to the xture. See wiring section for details.

4. Push up and slide the Junction Box section into the

ceiling. Be sure the Mounting Flag is folded in as the

xture slides through ceiling hole. (Fig. 3)

5. For the Wallwash Model, orient the xture such that the

Reector is in correct orientation. Wall Wash xtures are

provided with swivel arm for maximum adjustability in all

construction situations. Look for ‘Towards the Wall’ label

on the xture. (Fig. 2)

6. To secure xture into ceiling, swing Mounting Flag

outward by turning Flag Screw clockwise. Ceiling

Flange should be snug tight against ceiling. DO NOT

OVERTIGHTEN SCREWS.

7. Insert dust protector to protect the LED & Reector until

Trim Assembly is ready to be installed.

Supply wires

Fig: 1

Junction Box

Screw

B B

C C

D D

1234

L I G H T I N G 170 LUDLOW AVE., NORTHVALE, NJ 07647

TITLE

MATERIAL: PART No.: DRAWING NAME:

DATE: REV DATE: REV

DRAWN BY: SCALE SHEET:

THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE

PROPERTY OF RAB LIGHTING, INCORPORATED

ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF

RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING

ECN #

REV DESCRIPTION DATE

Init.

TOLERANCES

.02

.XX

.01

.XXX

.005

ANGLES

SCALE 0.500

Reector

Fig: 3

Flag Screws

RDLED6R RDLED6S

Cut-Out Diameter: 7” Cut-Out: 7”x7”

Junction Box

B B

C C

D D

1234

L I G H T I N G 170 LUDLOW AVE., NORTHVALE, NJ 07647

TITLE

MATERIAL: PART No.: DRAWING NAME:

DATE: REV DATE: REV

DRAWN BY: SCALE SHEET:

THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE

PROPERTY OF RAB LIGHTING, INCORPORATED

ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF

RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING

ECN #

REV DESCRIPTION DATE

Init.

TOLERANCES

.02

.XX

.01

.XXX

.005

ANGLES

SCALE 0.500

Mounting Flag

Fig: 2

Flag Screw

Heat Sink

Ceiling Flange

RDLED6 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

TROUBLESHOOTING

1. Check that the line voltage at the xture is correct. Refer

to wiring directions.

2. Is the xture grounded properly?

3. For questions on compatibility of dimmers purchased

separately or existing dimmers, refer to

www.rabweb.com

4. If the LED is blinking the xture may be overheating.

Remove the Trim assembly and if the xture is labeled

‘BLINKING LIGHT OF THIS THERMALLY PROTECTED

LUMINAIRE MAY INDICATE OVERHEATING’ allow the

xture to cool down. Determine cause of overheating

and remove. Fixtures with this label have a thermal

protector that turns xture o above a certain

temperature. It will automatically restart when cool.

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool enough to

touch. Do not clean or maintain while xture is energized.

1. Do not open xture to clean the LED. Do not touch the

LED.

2. Do not touch reector, lens or trim cone.

3. Do not clean any xture surface with wood base cleaning

material such as paper towels or tissues. Only use micro

ber cleaning cloth.

Easy Installation & Product Help

Tech Help Line

Call our experts 888 RAB-1000

rthvale, New Jersey 07647 USA

rabweb.com

Visit our website for product info

Answered promptly sales@rabweb.com

RDLED6 IN-1214

B B

C C

D D

1234

R A B

L I G H T I N G 170 LUDLOW AVE., NORTHVALE, NJ 07647

TITLE

MATERIAL: PART No.: DRAWING NAME:

DATE: REV DATE: REV

DRAWN BY: SCALE SHEET:

THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE

PROPERTY OF RAB LIGHTING, INCORPORATED

ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF

RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING

ECN #

REV DESCRIPTION DATE

Init.

TOLERANCES

.02

.XX

.01

.XXX

.005

ANGLES

SCALE 0.500

Spring Clip

Opening

Trim Ring

TRIM ASSEMBLY MOUNTING

1. Check to ensure the Trim clip opening is free of debris

and paint.

2. Match the Trim Spring Clips (3) to Sping Clip Openings.

Trim Ring should be ush to ceiling.

Note: For round xtures, Trim Spring Clip Opening Pattern is

not Symmetrical. Trim Ring must be orientated as in Fig. 4.

Install Trim Spring Clip marked with red dot on Trim Ring into

the Spring Clip Opening marked with red dot as in Fig. 4.

3. For the Wallwash Model, aim the xture such that the

reector is in correct orientation. Look for ‘Towards the

Wall’ label on the reector.

B B

C C

D D

1234

R A B

L I G H T I N G 170 LUDLOW AVE., NORTHVALE, NJ 07647

TITLE

MATERIAL: PART No.: DRAWING NAME:

DATE: REV DATE: REV

DRAWN BY: SCALE SHEET:

THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE

PROPERTY OF RAB LIGHTING, INCORPORATED

ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF

RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING

ECN #

REV DESCRIPTION DATE

Init.

TOLERANCES

.02

.XX

.01

.XXX

.005

ANGLES

SCALE 0.500

Trim Spring Clip

Fig: 4

WIRING

RISK OF FIRE. Universal voltage driver permits operation at

120V thru 277V, 50 or 60 Hz. For Non-Dimming, Electronic

Low Voltage (ELV) and Triac Dimming follow the wiring

directions in Fig. 5.

1. Connect the GROUND wire from xture to supply ground.

2. Connect the black xture lead to the (+) LINE supply lead.

3. Connect the white xture lead to the (-) COMMON supply

lead.

Lutron L3D Hi-Lume series drivers work with Lutron 3-Wire

Control (Fig. 6) or EcoSystem Digital Controls (Fig. 7).

Note: See www.lutron.com for complete instructions and functional

compatibility of Lutron drivers with Lutron or other control systems/

dimmers.

Fig: 5

Fig: 6

Fig: 7

Note: These instructions do not cover all details or variations in

equipment nor do they provide for every possible situation during

installation, operation or maintenance. RAB cannot troubleshoot

Lutron systems and have provided only basic information. See

www.lutron.com for complete instructions and functional

compatibility of Lutron Drivers with Lutron or other Control systems/

dimmers.

RDLED6 INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

14.53

[369,1]

4.97

[126,1]

7.52

[191,1]

2.49

[63,3]

DIMENSIONAL DRAWING

RDLED6R

RDLED6S