Minka Group 6522-77 User manual

6522-77
Minka Group
Brand
Minka Group
Model
6522-77
Type
User manual

Minka Group 6522-77 is a versatile lighting fixture designed for easy installation and customizable illumination. It features a sturdy mounting plate that securely attaches to outlet boxes, making it suitable for a range of indoor lighting applications. The fixture accommodates various light bulbs, allowing you to adjust the brightness and ambiance to your preference, ensuring optimal lighting for your space.

Minka Group 6522-77 is a versatile lighting fixture designed for easy installation and customizable illumination. It features a sturdy mounting plate that securely attaches to outlet boxes, making it suitable for a range of indoor lighting applications. The fixture accommodates various light bulbs, allowing you to adjust the brightness and ambiance to your preference, ensuring optimal lighting for your space.

INSTALLATION INSTRUCTIONS
Item#6522 （New. 08/23/2012）
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 2
Fig. 1
MOUNTING THE FIXTURE (Fig. 1 )
1. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
2. Shut off power at the circuit breaker and remove old
fixture, including the mounting hardware.
3. Position Mounting Plate (B) on the wall, and mark
location of two mounting holes. Drill the hole on the
wall. Insert the Plastic Anchors (K) into the wall.
4. Attach the Mounting Plate (B) to the Outlet box (A) in
the wall using the two screws (C). The side of the
mounting plate marked “GND” must face out.
5. Place the Wood Screws (L) through the hole into the
Plastic Anchors (K) secure the Mounting Plate (B).
CONNECTING THE WIRES (Fig. 2)
6. At this point, connect the electrical wires as shown
in Fig. 2, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or
bare copper), connect the fixture’s Ground Wire to it.
Otherwise, connect the fixture’s Ground Wire
directly to the mounting plate or Reinforcement
Plate using the Green Screw provided. After wires
are connected, tuck them carefully into the outlet
box.
FINISHING THE INSTALLATION (Fig. 1)
7. Place Fixture Body (F) over Mounting Plate (B),
fasten with Screws (D) by using Allen Wrench (E)
provided.
8. Install light bulbs (G) (not included) in accordance
with the fixture’s specifications. (DO NOT EXCEED
THE MAXIMUM WATTAGE RATING!) (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
9. While holding the Glass panel (H) toward the Fixture
body (F), insert the Plastic Washer (N) and Cast part
(I) between end of glass panel and Holder (M), then
secure with the Finial (J).
Your installation is now complete. Return power to
the outlet box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-1623E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
N
J
G
M
F
H
D
E
B
K
A
C
I
L
  • Page 1 1

Minka Group 6522-77 User manual

6522-77
Minka Group
Brand
Minka Group
Model
6522-77
Type
User manual

Minka Group 6522-77 is a versatile lighting fixture designed for easy installation and customizable illumination. It features a sturdy mounting plate that securely attaches to outlet boxes, making it suitable for a range of indoor lighting applications. The fixture accommodates various light bulbs, allowing you to adjust the brightness and ambiance to your preference, ensuring optimal lighting for your space.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents