George Kovacs P1424-674-L Installation guide
- Type
- Installation guide
INSTALLATION INSTRUCTIONS
Item#P1424-674-L (New. 07/07/2018)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the mounting
hardware.
2. Carefully remove the fixture from the carton and check
that all parts are included as shown in the illustration.
3. Position the mounting plate (A) on the wall, and mark
location of the two mounting holes. Drill the holes on the
wall, and then insert the plastic anchors (P).
4. Attach the mounting plate (A) to the junction box using
mounting screws (B) (Size: #8-32N*L0.5”). The side of the
mounting plate marked “GND” must face out.
5. Secure the mounting plate (A) by inserting the wood
screws (Q) through the holes on the mounting plate into
the plastic anchors (P).
CONNECTING THE WIRES (Fig. 2)
6. At this point, connect the electrical wires as shown in Fig.
2, making sure that all wire connectors are secured. If
your outlet box has a ground wire (green or bare copper),
connect the fixture’s ground wire to it. Otherwise, connect
the fixture’s ground wire directly to the mounting plate
using the green screw provided. After the wires are
connected, tuck them carefully inside the junction box.
FINISHING THE INSTALLATION (Fig.1)
7. Place fixture body (D) over mounting plate (A) and fasten
with Screws (C).
8. Through screws (E) onto the plastic gasket (F) and the
glass panel (G), then secure the glass into the fixture
body (D).
Your installation is now complete. Return power and test the
fixture.
CAUTION/ATTENTION: When handling the fixture, do not
apply pressure to the LEDs. Hold the fixture by the base or
fixture body (D) only.
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician
without cutting the wires and without damaging the
decorative element to which the fixture is attached. See
installation steps for more details (Fig.3)
Warning: Turn off power at the fuse box or circuit
breaker before replacing the LED module.
a. To remove the fixture from the wall: loosen screws (C),
and remove the wire connectors. Then place the fixture
on a clear flat surface. (Fig.1)
b. Loosen screws (E) and remove plastic gasket (F) and
glass panel (G).
c. Loosen screws (M) to remove the heat sink (N).
d. Loosen screws (H) to remove end caps (I) and glass
shield (J).
e. Loosen screw (L) and then using a pin to press the hole
of the quick connector and disconnect the wire
respective.
f. Carefully remove the LED module (K) from heat sink (N)
of the fixture body.
Reverse steps a-e for installing the new LED module
Note: The LED module should be provided by a specified
supplier.
Note: Illustration (Fig. 1 & 3) on this manual is for
installation purposes only. It may or may not be identical
to the fixture purchased.
LA-2957E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set#A-021-650132
-Mounting Plate
-Ground Screw
-Mounting Screw*2
IMPORTANT: FIXTURE SHOULD BE INSTALLED
BY A QUALIFIED ELECTRICIAN TO ENSURE
PROPER WIRING AND INSTALLATION.
Dimmable with ELV and/or LED compatible wall
dimmer switches.
G
F
E
A
P
C
Q
B
D
G
E
H
I
J
K
L
M
N
F
-
1
George Kovacs P1424-674-L Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
