RZE-BT700E Manual
How to pair for stereo mode
1.When the L&R units are used independently
They can be used as 2 complete and independent Bluetooth earbuds.
Long press MFB for 3 seconds to turn on the earbud(blue indicator light quick
flash 3 times)
After turning on, double-click MFB enter pairing mode(red&blue indicator lights
flash)
Turn on your mobile phones Bluetooth function and search for the nameT04 to
connect it.( indicator light off once connected)
Long press MFB for 3 seconds until red indicator light quick flash 3 times to
power off the earbud
After the first use, just long press MFB until the blue indicator light flash, and the
earbud will re-connect with the mobile phone automatically.
2.When the L&R units are used together
Long press A&B earbuds MFB at same time for 3 seconds until blue indicator
flash
A&B earbuds will connect automatically firstly, and then enter the pairing state.
Blue lights off once A&B earbuds paired successfully
Turn on your mobile phones Bluetooth and search for the nameT04 to connect
it.( indicator lights off once connected)
Long press A or B MFB for 3 seconds until red indicator light quick flash 3 times
to power off 2 earbuds
Note: If A&B earbuds doesnt pair successfully and can’t listen to music, please
try steps as follow.
Place the earbuds and mobile phone within 1 meter.
Make sure 2 earbuds was turned off.
Long press 2 earbuds MFB for 3 seconds at the same time to turn them on (blue
indicator light quick flash 3 times)
Then double-click 2 earbuds MFB enter pairing mode(red&blue indicator lights
flash), 2 earbuds only blue lights flash in the later.
Waiting 2 earbuds pair successfully( 1 earbud blue indicator light flash, another
earbud lights off)
If 2 earbuds blue lights flash for a long time didn't pair successfully, double-click
2 earbuds MFB enter pairing mode again(red&blue indicator lights flash),until
pair successfully
Long press any of the 2 earbuds MFB for 3 seconds until red indicator quick
flash 3 times ,2 earbuds power off at the same time, it mean 2 earbuds paired
successfully.
Long press 2 earbuds MFB at same time for 3 seconds until blue indicator lights
flash
Turn on your mobile phones Bluetooth and search for the nameT04 to connect
it.( 2 earbudss indicator lights off once connected with phone)
Phone calling function
The earbud can be used to answer the call when it connects to the mobile phone
successfully.
1When the L&R units are used together , only main earbud A can work.
2When the L&R units are used independently, both of them can work.
Main earbud A will have a reminder when call coming. And can enter different
function according to following operation.
1Answer phone call--press MFB to answer incoming call, and press it again to
end
2Reject phone call--long press MFB for 2 seconds
Music Playing function
Press MFB to stop the music, and press it again to play. Please adjust the volume
of music on your phone.
Double click MFB to next track
Charging operation
The base charge the earbuds
Putting earbuds into the charging case (please make the charging interface is
correctly placed, and earbuds will indicates red light when the earbuds is being
charged), the earbuds will automatically enter the charging state
When the earbuds is charging, the red light of earbuds is on, the red light will off
after fully charged
USB cable charge the charging case:
When using the USB cable charge the charging case, the back of charging cases
light will be red. The red light will off when fully charged
LED light flashing situation
Turn on the earbuds: blue indicator light quick flash 3 times
Turn off the earbuds: red indicator light quick flash 3 times
When two earbuds is entering pair mode: red&blue lights flash, then only blue
indicator light flash
Two earbuds pair successfully: 1 earbud blue indicator light flash, another earbud
lights off
Earbuds pair successfully with phone: two earbuds lights off
Charging earbuds: earbuds indicator light is red
The earbuds charging is completed: earbuds lights off
Charging earbuds by charging case : the indicator light behind case is green
Charging case by USB cable: the indicator light behind case is red, the red light
will off when fully charged
Product specification:
Bluetooth versionV4.1
Earbuds weight4.1g*2
Charging case weight39.8g
Earbuds battery capacity55mAh
Working range10m
Working voltage3.7V
Standby time100H
Music playing time2.5H (60% volume)
Bluetooth certification
Bluetooth technology conform to the provisions of the state standards
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment. This device complies with Part
15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre lefonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI