Garmin GPSMAP® 8616 Installation guide

Brand: Garmin

Model: GPSMAP® 8616

Type: Installation guide

GPSMAP

8400/8600 SERIES

INSTALLATION

INSTRUCTIONS

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, install the device according to these instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin

Product Support.

Contacting Garmin Support

• Go to support.garmin.com for help and information, such as

product manuals, frequently asked questions, videos, and

customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

Updating the Device Software

You may need to update the device software when you install

this device or add an accessory to the network. You can use

one of two methods to update the software.

• Use the ActiveCaptain

™

app.

• Download the update from www.garmin.com/support

/software/marine.html using a memory card (32 GB max.)

and a computer running Windows

operating system.

For more information, see the owner's manual at

www.garmin.com/manuals/GPSMAP84xx-86xx.

Registering Your Device

Help us better support you by completing our online registration

today. You can register your device using one of two methods.

• Use the ActiveCaptain app.

• Go to my.garmin.com/registration and sign into your Garmin

account to register the device.

Keep the original sales receipt, or a photocopy, in a safe place.

After you add devices to the chartplotter network, register the

new devices.

Tools Needed

• Drill and drill bits

◦ 3.0 mm (

in.) drill bit for bail mounting

◦ 14.6 mm (

in.) drill bit for flush mounting

◦ 3.2 mm (

in.) drill bit for flush mounting using wood

screws

◦ 3.6 mm (

in.) drill bit for flush mounting using the nut

plate

◦ 6.0 mm (

in.) drill bit for flush mounting using the nut

plate

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine-grade sealant, approved for use on plastics

(recommended)

Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

You can flush mount the device in the dashboard, or bail mount

the device on the dashboard.

When selecting a mounting location, observe these

considerations.

• You should mount the device to provide an optimal viewing

angle as you operate your boat.

• You must select a location that is strong enough to support

the weight of the device and protect it from excessive

vibration or shock.

• To avoid interference with a magnetic compass, you must not

mount the device closer to a compass than the compass-safe

distance value listed in the product specifications.

• You must select a location that allows room for the routing

and connection of all cables.

• You should select a location that allows for easy access to

the device touchscreen.

• You should select a location that allows for access to the

microSD

card in the back of the device. If the location does

not allow access, you must insert the memory cards before

installing the device.

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

You can use the bracket to bail mount the device on a flat

surface. The bracket and hardware are included in some

models.

March 2019

190-02469-02_0A

Using the bail-mount bracket as a template, mark the pilot

holes .

Using a 3 mm (

in.) drill bit, drill the pilot holes.

Secure the bail-mount bracket to the surface using the

included washers and wood screws .

Install the bail-mount knobs on the sides of the device.

Place the device in the bail-mount bracket, and tighten the

bail-mount knobs.

Install the trim caps by snapping them in place around the

edges of the device.

Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

Use only the included hardware when mounting this device.

Using mounting hardware not provided with the device may

damage the device.

To avoid potential damage to the powder coating, use only the

included screws to mount the device. Using screws other than

the ones included will void your warranty.

Do not remove the blue, rubber protective bumper until after the

installation is complete. The bumper helps protect the device

from damage during installation.

If you will not have access to be back of the device and the

microSD memory card slots after installations, you should install

the microSD memory card prior to installation.

The included template and hardware can be used to flush mount

the device in your dashboard. There are three options for

hardware based on the mounting surface material.

• You can drill pilot holes and use the included wood screws.

• You can drill holes and use the included nut plates and

machine screws. The nut plates can add stability to a thinner

surface.

• You can drill holes, tap them to M4, and use the included

machine screws.

Trim the template and make sure it fits in the location where

you want to mount the device.

Secure the template to the selected location.

Using an 14.6 mm (

in.) drill bit, drill one or more of the

holes inside the corners of the solid line on the template to

prepare the mounting surface for cutting.

Using a jigsaw or rotary tool, cut the mounting surface along

the inside of the solid line on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the device fits correctly in the cutout, ensure the

mounting holes on the device line up with the larger 6 mm

(

in.) holes on the template.

If the mounting holes on the device do not line up, mark the

new hole locations.

Based on your mounting surface, drill or punch and tap the

larger holes:

• Drill 3.2 mm (

in.) pilot holes for the included wood

screws, and skip to step 18.

• Drill 6 mm (

in.) holes for the included nut plate and

machine screws.

• Drill and tap M4 holes for the included machine screws,

and skip to step 18.

If using the nut plates, starting in one corner of the template,

place a nut plate over the larger hole drilled in step 9.

The smaller hole on the nut plate should line up with the

smaller 3.6 mm (

in.) hole on the template.

If the smaller hole on the nut plate does not line up with the

smaller hole on the template, mark the new hole location.

Repeat steps 10 and 11 for each nut plate.

Using a 3.6 mm (

in.) drill bit, drill the smaller holes.

Remove the template from the mounting surface.

Starting in one corner of the mounting location, place a nut

plate on the back of the mounting surface, lining up the

large and small holes.

The raised portion of the nut plate should fit into the larger

hole.

Secure the nut plate to the mounting surface by fastening an

included M3 screw through the smaller 3.6 mm (

in.)

hole.

Repeat steps 15 and 16 for each of the nut plates along the

top and bottom of the device.

Install the foam gasket on the back of the device.

The pieces of the foam gasket have adhesive on the back.

Make sure you remove the protective liner before installing

them on the device.

If you will not have access to the back of the device after you

mount it, connect all necessary cables and install microSD

cards in the back of the device before placing it into the

cutout.

NOTE: To prevent corrosion of the metal contacts, cover

unused connectors with the attached weather caps.

Apply marine sealant between the mounting surface and the

device to properly seal and prevent leakage behind the

dashboard.

If you will have access to the back of the device, apply

marine sealant around the cutout.

Place the device into the cutout.

Secure the device to the mounting surface using the included

M4 screws or wood screws, depending on the mounting

method.

Carefully remove and discard the rubber protective bumper.

Wipe away all excess marine sealant.

Install the trim caps by snapping them in place around the

edges of the device.

Connection Considerations

When connecting this device to power and to other Garmin

devices, you should observe these considerations.

• The power and ground connections to the battery must be

checked to make sure they are secured and cannot become

loose.

• The cables may be packaged without the locking rings

installed. The cables should be routed before the locking

rings are installed.

• After installing a locking ring on a cable, you should make

sure the ring is securely connected and the o-ring is in place

so the power or data connection remains secure.

Connecting to Power

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

Route the power cable to the power source and to the device.

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

Connect the power cable to the device, and turn the locking

ring clockwise to tighten it.

Additional Grounding Consideration

This device should not need additional chassis grounding in

most installation situations. If you experience interference, you

can use the grounding screw on the housing to connect the

device to the water ground of the boat to help avoid the

interference.

Power Cable Extensions

If necessary, the power cable can be extended using the

appropriate wire gauge for the length of the extension.

Item Description

Fuse

Battery

6 ft. (1.8 m) no extension

Item Description

Splice

• 10 AWG (5.26 mm²) extension wire, up to 15 ft. (4.6 m)

• 8 AWG (8.36 mm²) extension wire, up to 23 ft. (7 m)

• 6 AWG (13.29 mm²) extension wire, up to 36 ft. (11 m)

Fuse

8 in. (20.3 cm)

Battery

8 in. (20.3 cm)

36 ft. (11 m) maximum extension

Garmin Marine Network Considerations

NOTICE

A Garmin Power over Ethernet (PoE) Isolation Coupler (P/N

010-10580-10) must be used when connecting any third-party

device, such as a FLIR

camera, to a Garmin Marine Network.

Connecting a PoE device directly to a Garmin Marine Network

chartplotter damages the Garmin chartplotter and may damage

the PoE device. Connecting any third-party device directly to a

Garmin Marine Network chartplotter will cause abnormal

behavior on the Garmin devices, including the devices not

properly turning off or the software becoming inoperable.

This device can connect to additional Garmin Marine Network

devices to share data such as radar, sonar, and detailed

mapping. When connecting Garmin Marine Network devices to

this device, observe these considerations.

• All devices connected to the Garmin Marine Network must be

connected to the same ground.

• A Garmin Marine Network cable must be used for all Garmin

Marine Network connections.

◦ Third-party CAT5 cable and RJ45 connectors must not be

used for Garmin Marine Network connections.

◦ Additional Garmin Marine Network cables and connectors

are available from your Garmin dealer.

• The NETWORK ports on the device each act as a network

switch. Any compatible device can be connected to any

NETWORK port to share data with all devices on the boat

connected by a Garmin Marine Network cable.

Station Connection Considerations

This device can be set up in conjunction with other compatible

Garmin devices to work together as a station. When planning

stations on your boat, observe these considerations.

• Devices earlier than the GPSMAP 8000 series and GPSMAP

8500 series cannot be used in a station.

• Although it is not necessary, it is recommended that you

install all of the devices you plan to use in one station near

each other.

• No special connections are necessary to create a station, as

long as all of the devices are connected to the Garmin Marine

Network (Garmin Marine Network Considerations, page 3).

• Stations are created and modified using the device software.

See the owner's manual provided with the device for more

information.

NMEA 2000

Considerations

NOTICE

If you are connecting to an existing NMEA 2000 network,

identify the NMEA 2000 power cable. Only one NMEA 2000

power cable is required for the NMEA 2000 network to operate

properly.

A NMEA 2000 Power Isolator (010-11580-00) should be used in

installations where the existing NMEA 2000 network

manufacturer is unknown.

If you are installing a NMEA 2000 power cable, you must

connect it to the boat ignition switch or through another in-line

switch. NMEA 2000 devices will drain your battery if the NMEA

2000 power cable is connected to the battery directly.

This device can connect to a NMEA 2000 network on your boat

to share data from NMEA 2000 compatible devices such as a

GPS antenna or a VHF radio. The included NMEA 2000 cables

and connectors allow you to connect the device to your existing

NMEA 2000 network. If you do not have an existing NMEA 2000

network you can create a basic one using cables from Garmin.

If you are unfamiliar with NMEA 2000, you should read the

“NMEA 2000 Network Fundamentals” chapter of the Technical

Reference for NMEA 2000 Products. You can find this document

using the “Manuals” link on the product page for your device at

www.garmin.com.

The port labeled NMEA 2000 is used to connect the device to a

standard NMEA 2000 network.

Item Description

NMEA 2000 compatible Garmin device

GPS antenna

Ignition or in-line switch

NMEA 2000 power cable

NMEA 2000 drop cable

12 Vdc power source

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

NMEA 2000 terminator or backbone cable

J1939 Engine Network Connection Considerations

NOTICE

You must use a Garmin GPSMAP J1939 accessory cable when

connecting the chartplotter to the J1939 engine network to

prevent corrosion due to moisture. Using a different cable voids

your warranty.

If you have an existing engine network on your boat, it should

already be connected to power. Do not add any additional power

supply.

This chartplotter can connect to an engine network on your boat

to read data from compatible devices such as certain engines.

The engine network follows a standard and uses proprietary

messages.

You should connect only one chartplotter to one engine network.

Connecting more than one chartplotter to one engine network

may result in unexpected behavior.

The port labeled J1939 is used to connect the device to the

existing engine network. You must route the cable within 6 m

(20 ft.) of the engine network backbone.

The Garmin GPSMAP J1939 accessory cable requires

connection to a power source and proper termination. For more

information on connecting to your engine network, see the

manufacturer's engine documentation.

Pin Wire Color Description

Bare Shield

Red Power, positive

Black Power, negative

White CAN High

Blue CAN Low

HDMI

Video Considerations

NOTICE

To prevent corrosion due to moisture, you must use Garmin

GPSMAP accessory cables when connecting the chartplotter to

the video source or display. Do not connect a media player stick

directly into the back of the chartplotter. Using different cables or

connecting a media player stick into the back of the chartplotter

voids your warranty.

This chartplotter allows video input from HDMI video sources,

such as a Chromecast

™

device or a Blu-Ray

™

player. You can

view protected HDMI content (HDCP content) on the chartplotter

screen. HDMI video is shared across the Garmin Marine

Network, but it is not shared across the NMEA 2000 network.

HDCP content is not shared across the Garmin Marine Network.

Through the HDMI OUT port, you can duplicate the chartplotter

screen on another device, such as a television or monitor. You

cannot view HDCP content on the duplicated screen.

The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft)

long. If you need a longer cable, you should use an active HDMI

cable only. You need an HDMI coupler to connect the two HDMI

cables.

You need a Garmin GPSMAP USB OTG adapter cable to power

a media player stick. The USB port can supply up to 2.5 W to

power a media player stick.

You must make all cable connections in a dry environment.

Item Description

GPSMAP 8400/8600 chartplotter

Display with an HDMI In port, such as a computer or television

GPSMAP HDMI cable (HDMI IN)

GPSMAP USB OTG adapter cable to power the HDMI source, if

possible (2.5 W maximum)

GPSMAP HDMI cable (HDMI OUT)

HDMI source, such as a Blu-Ray player or Chromecast device

Dry environment, protected from moisture

Composite Video Considerations

This chartplotter allows video input from composite video

sources using the port labeled CVBS IN. When connecting

composite video, you should observe these considerations.

• The CVBS IN port uses a BNC connector. You can use a

BNC to RCA adapter to connect a composite-video source

with RCA connectors to the CVBS IN port.

• Video is shared across the Garmin Marine Network, but it is

not shared across the NMEA 2000 network.

Touchscreen Controls for a Connected Computer

NOTICE

To prevent corrosion due to moisture, you must use Garmin

GPSMAP accessory cables when connecting the chartplotter to

the computer. Using different cables voids your warranty.

You can connect the chartplotter to a computer to see the

computer screen and to control the computer using the

chartplotter touchscreen. To see the computer screen, you must

connect the computer to the HDMI IN port. To control the

computer using the chartplotter touchscreen, you must connect

the computer to the USB port.

The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft)

long. If you need a longer cable, you should use an active HDMI

cable only. You need an HDMI coupler to connect the two HDMI

cables. You must make all cable connections in a dry

environment.

The Garmin GPSMAP USB accessory cable is 4.5 m (15 ft)

long. If you need a longer cable, you should use a USB hub or

USB repeater extension cable only. You should make all cable

connections in a dry environment.

Item Description

Garmin chartplotter

Computer

GPSMAP USB cable

Dry environment, protected from moisture

GPSMAP HDMI cable (HDMI IN)

NMEA

0183 with Audio Cable Pinout

The optional NMEA 0183 with audio cable (010-12852-00)

includes bare wires and an RCA connector for an audio out

connection to a stereo, including FUSION

stereos. This cable

can be purchased from garmin.com or your local Garmin dealer.

After installing, you can connect the RCA connector to the AUX

input of the stereo. The HDMI input is output to the stereo.

The NMEA 0183 with audio cable provides one differential

NMEA 0183 input and output port.

Pin Wire Function Wire Color

1 NMEA 0183 Rx/A (In +) Orange/white

2 NMEA 0183 Rx/B (In -) White

3 NMEA 0183 Tx/B (Out -) Pink

4 NMEA 0183 Tx/A (Out +) Gray

5 Ground Black

6 Alarm Yellow

7 Accessory on Orange

8 Ground (shield) Brown

9 Audio Left Channel White

10 Audio Common Blue/red

11 Audio Right Channel Red

For more information on NMEA 0183 wiring with this cable, see

the cable instructions at www.garmin.com/manuals/nmea0183

_audio_cable.

NMEA 0183 Connection Considerations

• The chartplotter provides one Tx (transmit) port and one Rx

(receive) port.

• Each port has 2 wires, labeled A and B according to the

NMEA 0183 convention. The corresponding A and B wires of

each internal port should be connected to the A (+) and B (-)

wires of the NMEA 0183 device.

• You can connect one NMEA 0183 device to the Rx port to

input data to this chartplotter, and you can connect up to

three NMEA 0183 devices in parallel to the Tx port to receive

data output by this chartplotter.

• See the NMEA 0183 device installation instructions to identify

the transmit (Tx) and receive (Rx) wires.

• You must use 28 AWG, shielded, twisted-pair wiring for

extended runs of wire. Solder all connections and seal them

with heat-shrink tubing.

• Do not connect the NMEA 0183 data wires from this device

to power ground.

• The power cable from the chartplotter and the NMEA 0183

devices must be connected to a common power ground.

• The internal NMEA 0183 ports and communication protocols

are configured on the chartplotter. See the NMEA 0183

section of the chartplotter owner's manual for more

information.

• See the chartplotter owner's manual for a list of the approved

NMEA 0183 sentences that the chartplotter supports.

Specifications

Device Specification Measurement

All models Temperature range From -15° to 55°C (from 5° to

131°F)

Material Polycarbonate plastic and die-

cast aluminum

Water rating

IEC 60529 IPX7

Input voltage From 10 to 32 Vdc

Fuse 10 A, 125 V fast-acting

NMEA 2000 LEN 2

NMEA 2000 draw 75 mA max.

Max. waypoints 5,000

Max. routes 100 (250 waypoints each)

Max. active track points 50,000 points, 50 saved

tracks

Memory card 2 microSD card slots in the

back of the device; 32 GB

max. card size

Wireless frequency and

protocols

Wi‑Fi

and ANT

technologies

2.4 GHz @ 12.3 dBm nominal

HTML integration Compatible with OneHelm

™

integration

10-inch

models

Dimensions (W × H ×

259.9 × 205.1 × 75.1 mm

(10

× 8

× 2

in.)

Display size (W × H) 136.9 × 218.4 mm (5

in.)

Weight 2.4 kg (5.2 lb.)

Clearance behind flush-

mounted device

11.1 cm (4

in.)

Compass-safe distance 45 cm (17.7 in.)

Max. power usage at

10 Vdc

40.1 W

Typical current draw at

12 Vdc

1.5 A

Max. current draw at

12 Vdc

6.0 A

12-inch

models

Dimensions (W × H ×

302.8 × x 216.4 × 75.1 mm

(11

× 8

× 2

in.)

Display size (W × H) 257.3 × 145.2 mm (10

in.)

Weight 2.7 kg (6.0 lb.)

Clearance behind flush-

mounted device

11.1 cm (4

in.)

Compass-safe distance 35 cm (13.8 in.)

Max. power usage at

10 Vdc

45 W

Device Specification Measurement

Typical current draw at

12 Vdc

1.3 A

Max. current draw at

12 Vdc

6.0 A

16-inch

models

Dimensions (W × H ×

384.7 × 262.6 × 75.1 mm

(15

× 10

× 2

in.)

Display size (W × H) 345.2 × 194.6 mm (13

in.)

Weight 4.4 kg (9.6 lb.)

Clearance behind flush-

mounted device

11.1 cm (4

in.)

Compass-safe distance 105 cm (41.3 in.)

Max. power usage at

10 Vdc

52.1 W

Typical current draw at

12 Vdc

1.3 A

Max. current draw at

12 Vdc

6.0 A

Sonar models Frequencies

Traditional: 50/200, 77/200,

83/200 kHz

Single Channel CHIRP: from

40 to 240 kHz

Garmin ClearVü CHIRP:

260/455/800 kHz

Ultra High-Definition SideVü :

1,200 kHz, CHIRP range:

1,060 to 1,170 kHz

(dependent on transducer)

Transmit power (RMS)

CHIRP: 1000 W

Garmin ClearVü and SideVü

CHIRP: 500 W

Depth

5,000 ft. at 1 kW

The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to www.garmin.com

/waterrating.

Dependent upon the transducer.

Dependent upon the transducer rating and depth.

Dependent upon the transducer, water salinity, bottom type,

and other water conditions.

NMEA 2000 PGN Information

Transmit and Receive

PGN Description

059392 ISO acknowledgment

059904 ISO request

060160 ISO transport protocol: Data transfer

060416 ISO transport protocol: Connection management

060928 ISO address claimed

065240 Commanded address

126208 Request group function

126996 Product information

126998 Configuration information

127237 Heading/track control

127245 Rudder

127250 Vessel heading

127258 Magnetic variance

127488 Engine parameters: Rapid update

127489 Engine parameters: Dynamic

127493 Transmission parameters: Dynamic

127505 Fluid level

127508 Battery status

128259 Speed: Water referenced

PGN Description

128267 Water depth

129025 Position: Rapid update

129026 COG and SOG: Rapid update

129029 GNSS position data

129283 Cross track error

129284 Navigation data

129539 GNSS DOPs

129540 GNSS satellites in view

130060 Label

130306 Wind data

130310 Environmental parameters (obsolete)

130311 Environmental parameters (obsolete)

130312 Temperature (obsolete)

Transmit

PGN Description

126464 Transmit and receive PGN list group function

126984 Alert Response

127497 Trip parameters: Engine

Receive

PGN Description

065030 Generator average basic AC quantities (GAAC)

126983 Alert

126985 Alert text

126987 Alert threshold

126988 Alert value

126992 System time

127251 Rate of turn

127257 Attitude

127498 Engine parameters: Static

127503 AC input status (obsolete)

127504 AC output status (obsolete)

127506 DC detailed status

127507 Charger status

127509 Inverter status

128000 Nautical leeway angle

128275 Distance log

129038 AIS class A position report

129039 AIS class B position report

129040 AIS class B extended position report

129044 Datum

129285 Navigation: Route, waypoint information

129794 AIS class A static and voyage related data

129798 AIS SAR aircraft position report

129799 Radio frequency/mode/power

129802 AIS safety-related broadcast message

129808 DSC call Information

129809 AIS class B "CS" static data report, part A

129810 AIS class B "CS" static data report, part B

130313 Humidity

130314 Actual pressure

130316 Temperature: Extended range

130576 Trim tab status

130577 Direction data

J1939 PGN Information

The chartplotter can receive J1939 PGN sentences. The

chartplotter cannot transmit over the J1939 network.

Sentence Description

61443 Electronic engine controller 2

61444 Electronic engine controller 1

65031 Exhaust temperature

65172 Engine auxiliary coolant

65252 Shutdown

65253 Engine hours and revolutions

65262 Engine temperature 1

65263 Engine fluid level or pressure 1

65270 Inlet or exhaust conditions 1

65271 Vehicle electrical power

65279 Water in fuel indicator

65272 Transmission fluids 1

65248 Vehicle distance

65266 Fuel economy (liquid)

65276 Dash display

65226 Active diagnostic trouble codes

Garmin

, the Garmin logo, and GPSMAP

are trademarks of Garmin Ltd. or its

subsidiaries, registered in the USA and other countries. These trademarks may not be

used without the express permission of Garmin.

HDMI

is a registered trademark of HDMI Licensing, LLC. The microSD

logo is a

trademark of SD-3C, LLC.

NMEA

, NMEA 2000

, and the NMEA 2000 logo are

registered trademarks of the National Marine Electronics Association.

support.garmin.com

Garmin GPSMAP® 8616 Installation guide

Garmin GPSMAP® 8616 Installation guide

Garmin GPSMAP® 8616 Installation guide

Related papers

Other documents