Aiphone RY-1824L Install Manual

Brand: Aiphone

Model: RY-1824L

Type: Install Manual

- INSTRUCTIONS -

The RY-1824L door release relay module is an interface between the door release contact on the Aiphone master station

or CEU and the actual release mechanism. The contact closure directly from the master station or CEU has limited voltage

and current capacity. Use the RY-1824L to ensure that the contact rating will be sufficient for the electric strike or magnetic

lock used. The relay’s contact rating supports a majority of door release hardware available. This relay is recommended

for all AX, KB, JF, JO, and JP Series systems when using door release and will protect the built-in contact from possible

surge damage.

(Note: Use the RY-3DL when releasing more than two doors in a JP Series, or more than one door in a JF or KB Series).

RY-1824L

Form C Door Release Relay for AX, KB, JF, JO, and JP Series

WIRING DIAGRAMS:

Page 1

INSTALLATION:

1. Install near the power source for the door release mechanism, or behind the master station or CEU.

2. Secure wire connections with proper termination, such as wire nuts or crimp connectors.

3. Trim the wires to the desired length.

4. Trim the unused contact wire so the bare strands are not exposed.

RED: (+) Pos.

BLK: (-) Neg.

BRN: Common

ORG: N/O

YEL: N/C

RY-1824L COLOR CODE:

Input of Relay:

Red: (+) Positive

Black: (-) Negative

Output of Relay:

Brown: Common

Orange: N/O contact

Yellow: N/C contact

(See contact rating specs on page 4)

1A1

1A2

M(Out)

2A1

2A2

PS-2420UL

Door #1

JP-DV

3A1

3A2

4A1

4A2

DOOR 1DOOR 2

DOOR 3DOOR 4

Blk

Brn

Org

Yel

RY-1824L

Red

LOCK

POWER

Door

Release

Brn

Org

Yel

RY-1824L

Door

Release

Blk

Red

MAGNETIC LOCK

WIRING METHOD:

(Normally Closed contact)

LOCK

POWER

ELECTRIC STRIKE

WIRING METHOD:

(Normally Open contact)

Door #2

JP-DV

COM

N/O

N/C

NOTE: The door release contacts on the station are rated at 24V AC/DC, 500mA. The RY-1824L should be used in any

application where the strike or maglock has a higher voltage or draws more current. Otherwise, internal damage to the

master station could occur.

JP Series Wiring

19310 0519

JP-4MED

RY-1824L

Page 2

WIRING DIAGRAMS (cont):

KB Series Wiring

1A1

1A2

KB-3MRD

2A1

2A2

3A1

3A2

CN11

Org

Yel

PS-2420UL

KB-DAR

LOCK

POWER

Red

Blk

Brn

Org

Yel

ELECTRIC STRIKE

WIRING METHOD:

(Normally Open contact)

Connect

Yellow wire

of CN11

directly to +

on station

Red

Blk

Brn

Org

Yel

COM

N/C

MAGNETIC LOCK

WIRING METHOD:

(Normally Closed contact)

Use Brown and Yellow wires

when connecting to maglock

LOCK

POWER

To (-) of

power supply

Connect Red to

Orange lead of

CN11 on the

Master Station

NOTE: The door release contacts on the station are rated at 24V AC/DC, 500mA. The RY-1824L should be used in any

application where the strike or maglock has a higher voltage or draws more current. Otherwise, internal damage to the

master station could occur.

RY-1824L

NOTE:

Release contacts on the JF-2MED are from

the 4-pin connector included with the unit.

Connect Red & Brown wires as shown.

Orange & Yellow wires are not used.

Release contacts on the JO-1MD/1FD

are L/L terminals.

DC 18V

RELEASE

(L)Brn

(L)Red

JF-2MED

JO-1MD/1FD

Door Station

PS-1820UL

Red

Blk

Brn

Org

Yel

COM

N/O

N/C

Use Normally Open

contact for electric strike

ELECTRIC STRIKE

WIRING METHOD:

JF/JO SERIES:

PS-1820UL

Red

Blk

Brn

Org

Yel

COM

N/O

N/C

Use Normally Closed

contact for magnetic lock

MAGNETIC LOCK

WIRING METHOD:

DC 18V

RELEASE

(L)Brn

(L)Red

Add jumper

wire from

L/Brn to +

Add

jumper

wire from

L/Brn to +

NOTE:

Only wiring pertaining to connection of door

release relay is shown here. For complete system

information, please consult the installation manual

for the system you are installing.

+ -

LOCK

POWER

+ -

LOCK

POWER

JF-2MED

JO-1MD/1FD

WIRING DIAGRAMS (cont):

Page 3

NOTE: The door release contacts on the station are rated at 24V AC/DC, 500mA. The RY-1824L should be used in any

application where the strike or maglock has a higher voltage or draws more current. Otherwise, internal damage to the

master station could occur.

RY-1824L

Page 4

RY-1824L Instr.

0519

SPECIFICATIONS:

Power Source: Supplied by master station or CEU

Mounting: No mounting required

Terminations: Color-coded prewired pigtails

Relay Input: 18~24V DC, Red and Black wires, 22AWG

Relay Output: Brown, Yellow, Orange wires, 18AWG

Output rating: 8A at 250V AC, 5A at 30V DC

Wiring: 2 conductors from station’s door release contacts to RY-1824L

2 conductors from RY-1824L to release mechanism, with power wired in series

Dimensions (HxWxD): 1-7/16" x 13/16" x 7/16", with wires extending approx. 7-1/2"

D1 D3 D5 D7

D2 D4 D6 D8

DOOR RELEASE RELAY

L1 L2 L3 L4 L5 L6 L7 L8

M1 M3

M2 M4

VCH1 VCH2

X1 OUT X2

AX-320C

+ - + -

D-PS V-PS

RS-232C

POWER

VIDEO OUT

V1 V2

AIPHONE AX-084C

AX-8MV

AX-DV

Connect separate RY-1824L relay for each door release contact being used.

WIRING DIAGRAMS (cont):

AX-DV

AX Series Wiring

Red

Blk

Brn

Org

Yel

COM

N/O

Use Brown and Orange wires

when connecting to electric strike

LOCK

POWER

Red

Blk

Brn

Org

Yel

COM

N/C

Use Brown and Yellow wires

when connecting to maglock

LOCK

POWER

NOTE: The door release contacts are rated at 24V AC/DC,

500mA. The RY-1824L should be used in any application where

the strike or maglock has a higher voltage or draws more current.

Otherwise, internal damage to the Exchange Unit could occur.

Aiphone Corporation

www.aiphone.com

[email protected]

(800) 692-0200

PS-2420UL

RY-1824L

Aiphone RY-1824L Install Manual

Aiphone RY-1824L Install Manual

Aiphone RY-1824L Install Manual

Related papers

Other documents