GIGABIT
SATA
NAS
QUICK
INSTALL
GUIDE
MODEL 503662
INT-503662 -QIG-0208-01
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS
™
Gigabit SATA NAS, Model 503662.
This Quick Install Guide presents the rudimentary steps required to set up
and operate this device. For specifications and more detailed instructions,
refer to the user manual 1) on the CD enclosed with this product; 2) on the
Web site listed below; or 3) in some cases, printed and enclosed with
this product. Contact your INTELLINET NETWORK SOLUTIONS dealer
with comments or questions, or visit www.intellinet-network.com for
information on the latest software and firmware updates, related products
and additional contact information.
Safety Information
For the safety of users and their equipment, follow these safety
guidelines:
• This device is for indoor use only; DO NOT use it outdoors.
• DO NOT place this device in or near excessive heat or humidity.
• DO NOT yank any connected cables; disconnect them gently.
• If placing this dev ice at heights or on a wall, make sure it’s firmly
secured to prevent damage possible injury.
• Parts, such as cables, the housing or the power supply, are
dangerous should children put the small parts in their nose or mouth.
KEEP THIS DEVICE OUT THE REACH OF CHILDREN!
• The NAS will become hot when used a long time. This is normal and
is not a malfunction. Keep the device away from paper, cloth and other
flammable materials.
• There’s no user-serviceable part inside the router. If you find that the
router is not working properly, contact your dealer (place of purchase)
and ask for help. DO NOT disassemble the router. Doing so will void
the warranty.
• If the NAS device falls into water while turned on, DO NOT touch it!
Turn off its power source before you do anything, or contact an
experienced technician for help.
• If you smell something strange or see smoke coming out of the router
or power supply, remove the power supply or turn the power off
immediately, then call the dealer for help.
3
Package Contents
Before you start to install and operate this NAS device, make sure
the following items are enclosed; otherwise, contact your dealer for
assistance.
• Gigabit SATA NAS
• A/C power adapter
• Quick installation guide & user manual CDROM
Installation
1. HDD installation
a) Shut down the server, unplug the power cord and open the housing
by pressing on the side panels of the top cover (left and right side).
b) Un-screw the four screws holding the HDD cover in place using
a Phillips screw driver.
4
push in
un-screw
HDD cover
lift up
e) Once removed, you can find a bag holding screws and rubber feet.
You can use them after the installation to secure the housing. This
is optional.
f) Slide in the HDD into the HDD cover and place the HDD cover
in the drive bay of the SATA NAS
g) Connect the power and data cable to the SATA HDD
h) Fasten the HDD cover using the four screws of step b
i) Put the top cover back in place (see step a)
j) Connect the cables as shown in step 2
5
HDD cover
SATA HDD
6
2. Cable connection
a) Connect the included Ethernet cable to the
back of the Gigabit SATA NAS.
Connect the other end of the Ethernet cable
to a LAN switch or Router on your network.
Ideally, a DHCP server is installed
installed on your network which provides an
IP Address to the Gigabit SATA NAS.
b) Connect the power adapter to the power
outlet or a power strip. Connect the other
end to the DC input connector
on the backside of the SATA
NAS.
e) Power on the Gigabit SATA NAS by pressing the blue power
button.
3. Configuration
The Gigabit SATA NAS device is a network device designed to
obtain IP information from a DHCP server in your network. In most
cases this would be your Router.
The NAS supports UPnP and
will announce its presence to
UPnP enabled devices; e.g.,
your Windows computer.
Double-click the ‘UPnP NAS
Device’ icon to open up the
configuration page.
7
Alternatively, you can use the NAS Finder application from the
included Software CD.
NAS Finder is designed to
detect all NAS devices on
your network. Your NAS unit
should be listed with the
unit’s IP address.
Double-click the device name
or highlight the device name
and click on the ‘Configure’
button to bring up the
configuration page.
The default user name is
blank (don’t fill it out).
The default password is
‘admin’.
Additional installation instructions — as well as explanations for all
the setup options — can be found in the user manual on the enclosed
CD.
INTELLINET NETWORK SOLUTIONS
™
offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com.
Copyright © INTELLINET NETWORK
SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.
/