Quadratec 3rd Brake Light LED Ring Installation guide

Brand: Quadratec

Model: 3rd Brake Light LED Ring

Type: Installation guide

LED 3rd Brake Light Ring

with Y Adapter

For 2007 - 2018 JK & JKU Wrangler Vehicles: #12052.0904

READ ALL SAFETY MESSAGES AND UNDERSTAND ALL

INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL THIS

PRODUCT. ALWAYS WEAR SAFETY GLASSES DURING INSTALL.

PARTS LIST:

LED 3rd Brake Light Ring - QTY 1

“Y” Adapter Wiring Harness - QTY 1

REQUIRED TOOLS:

Safety Glasses

Lug Wrench & Socket

T20 Torx Driver or Bit

3rd_BRAKE_RING_12020_0904_A4.qxp_A4 6/16/20 12:54 PM Page 1

Before You Begin Installation:

Congratulations on your purchase of

the Quadratec LED 3rd Brake Light

Ring for your Jeep®Wrangler.

When unpacking, check to make sure all

parts are included and not damaged due

to shipping. If any part is missing or

broken, please call Customer Service

at 800-745-6037 as soon as possible.

Thank you again for your purchase

and let’s start the installation process.

A hazardous situation which, if not avoided, could result in death or

serious injury. You CAN be KILLED or SERIOUSLY HURT if you don’t

follow instructions.

A hazardous situation which, if not avoided, could result in minor or

moderate injury. You CAN be moderately HURT and also may suffer

property damage if you don’t follow instructions.

Careful attention is required to this instruction or operation but does

generally not relate to personal injury. Damage to your Quadratec®

product or other property may result if you don’t follow instructions.

A Few Words About Product Safety:

Your LED 3rd Brake Light is designed to

enhance the utility and enjoyment of

your off road capable vehicle. Before

installation, please take a moment to

review the following safety information

and installation instructions. Important

safety information is generally preceded

by one of three signal words indicating

the relative risk of injury.

The signal words mean:

WHEN ROUTING ELECTRICAL WIRES, ALWAYS AVOID PINCHING WIRES.

ALWAYS AVOID HOT OR MOVING COMPONENTS. ALWAYS SECURE WIRES

WITH CABLE TIES.

THIS PRODUCT IS INTENDED TO BE USE IN CONJUNCTION WITH YOUR

VEHICLE’S FACTORY CENTER HIGH MOUNTED 3RD BRAKE LIGHT.

NOT TO BE USED BY ITSELF OR AS A REPLACEMENT.

“Y” Adapter

Harness

3rd_BRAKE_RING_12020_0904_A4.qxp_A4 6/16/20 12:55 PM Page 2

Place the third brake light ring over the

studs on the tire carrier as shown with

the attached harness located at the

bottom of the ring. You may temporary

secure the brake light ring by finger

tightening one of the lug nuts on to

the tire carrier studs.

Open the tailgate of the vehicle and

locate the 4 T20 screws on the backside

of the factory 3rd brake light housing.

Remove the 4 screws with a T20 torx

driver.

Put on safety glasses. Remove the lug

nuts that secure the spare tire using lug

wrench and correct socket (factory lug

nuts use ¾” socket). Carefully remove

the spare tire. Pass the connector and

harness from the third brake light ring

behind the spare tire carrier and out

the top.

Installation Instructions:

3rd_BRAKE_RING_12020_0904_A4.qxp_A4 6/16/20 12:55 PM Page 3

Now plug one end of the “Y” harness

into the back of the factory brake light.

Once again make sure the connectors

fully engage and lock together.

Route and secure the “Y” harness into

the channel on the backside of the brake

light. Use the same routing and securing

clips that the factory harness used.

Connect the other end of the “Y”

harness to the brake light ring harness.

Remove factory brake light from the

housing and unplug the factory connec-

tor from the back of the brake light.

Plug the supplied “Y” harness into the

factory harness as shown. Make sure

the connectors fully engage & lock

together.

Factory

Harness

“Y” Adapter

Harness

Installation Instructions:

WHEN ROUTING ELECTRICAL WIRES, ALWAYS AVOID PINCHING WIRES.

ALWAYS AVOID HOT OR MOVING COMPONENTS. ALWAYS SECURE WIRES

WITH CABLE TIES.

3rd_BRAKE_RING_12020_0904_A4.qxp_A4 6/16/20 12:55 PM Page 4

Reinstall the factory brake light into the

tire carrier housing. Be careful not to

pinch any of the wires while rein-

stalling. Reinstall the 4 T20 screws

with a Torx driver.

Close the tailgate and reinstall the spare

tire and secure it with the 3 lug nuts.

Tighten by hand and do not use an im-

pact gun. This could overtighten the lug

nuts and damage the 3rd brake light ring.

Check brake lights for proper operation

before driving the vehicle.

Installation Instructions:

3rd_BRAKE_RING_12020_0904_A4.qxp_A4 6/16/20 12:55 PM Page 5

Quadratec® Exclusive

Three Year Limited Warranty

Your Quadratec®branded accessories are

covered by the following Limited Warranty

provided exclusively by Quadratec, Inc., 1028

Saunders Lane, West Chester PA 19380.

This Limited Warranty is the only warranty

made in connection with your purchase.

Quadratec neither assumes nor authorizes any

vendor, retailer or other person or entity to as-

sume for it any other obligation or liability in

connection with this product or Limited War-

ranty. This Limited Warranty does not apply

and is not cumulative to any accessory or part

distributed by Quadratec for which the Manu-

facturer provides a separate written warranty.

What is Covered: Subject to the terms, exclu-

sions and limitations herein and with respect

only to Quadratec branded accessories first sold

in the United States, Quadratec warrants to the

initial retail purchaser only that your

Quadratec accessory shall be free of defects in

material and workmanship: for a period of

three (3) years from date of retail purchase.

This Limited Warranty is not assignable and

shall terminate upon sale of the vehicle upon

which the Quadratec accessory is installed or

other transfer third persons.

All other warranties are hereby disclaimed, ex-

cept to the extent prohibited by applicable law

in which case any implied warranty of mer-

chantability or fitness for a particular purpose

on this product is limited to 3 year from date of

initial retail sale. Quadratec reserves the rights

to: (a.) require invoice or other proof your ac-

cessory is within the terms of this Limited

Warranty as a condition of warranty service

and, (b.) make future revisions to this product

and Limited Warranty without prior notice or

obligation to upgrade your product.

What is Not Covered:

Your Quadratec Limited Warranty does not

cover products or parts Quadratec determines

to have been damaged by or subjected to:

(a.) installation damage, alteration, modifica-

tion, combination with other parts, failure to

maintain or improper repair or service, (b.) nor-

mal wear & tear, cosmetic damage or damage

from moisture or water immersion, (c.) Acts of

God, accidents, misuse, negligence, inadequate

mounting or impact with vehicle(s), obstacles

or other aspects of the environment, (d.) theft,

vandalism or other intentional damage.

Remedy Limited to Repair/Replacement:

The exclusive remedy provided hereunder shall,

upon Quadratec inspection and at Quadratec’s

option, be either repair or replacement of prod-

uct or parts (new or refurbished) covered under

this Limited Warranty. Customers requesting

warranty consideration should first contact

Quadratec to obtain a RGA number

(610-701-3336). All labor, removal, shipping

and installation costs are customer’s

responsibility.

Other Limitations - Exclusion of Damages -

Your Rights Under State Law:

In consideration of the purchase price paid, nei-

ther Quadratec nor any independent Quadratec

distributor/licensee are responsible for any time

loss, rental costs, or for any incidental, conse-

quential, punitive or other damages you may

have or incur in connection with any part or

product purchased. Your exclusive remedy

hereunder for covered parts is repair/replace-

ment as described above.

This Limited Warranty gives you specific rights.

You may also have other rights that vary from

state to state. For example, some states do not

allow limitations of how long an implied war-

ranty lasts and /or do not allow the exclusion

or limitation of incidental or consequential

damages, so the limitations and exclusions

herein may not apply to you.

6.12.20 A4 Version

Part #12999.3095

3rd_BRAKE_RING_12020_0904_A4.qxp_A4 6/16/20 12:55 PM Page 6

Quadratec 3rd Brake Light LED Ring Installation guide

Brand: Quadratec

Model: 3rd Brake Light LED Ring

Type: Installation guide

Download PDF

report

Quadratec 3rd Brake Light LED Ring Installation guide

Quadratec 3rd Brake Light LED Ring Installation guide

Related papers

Other documents