Habitat GFW Canyon 1 Door 3 Drawer Sideboard User manual

Type
User manual
Page 1 of 16
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking.
Tools Required
x2
1.5 Hour
Set Up
PO No : _____
Version 1 - 210818
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Thank you for purchasing this versatile multi storage unit.
Please read the instructions carefully to ensure safe operation of this product.
Size:
Colour:
mc 07 x 6.93 x 5.58 (WDH)
Dark Oak
Page 2 of 16
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
Version 1 - 210818
INFORMATION
WARNINGS
This product is designed to hold 18Kg in total, spread evenly over the whole unit.
Do not exceed this weight.
We recommend that this unit is assembled in the room intended for use.
When you are ready to start, make sure that you have the right tools, plenty of space and
a clean, dry area for assembly.
Unwrap all packaging materials and place the components on top of the carton box or on
a clean floor to prevent them from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly
Tools are not included unless specified in parts list.
This product should only be used on a firm and level floor.
Keep small parts out of the reach of children.
Make sure the base remains in contact with the floor.
For safety, you must use the anti-tilt strap supplied (Q).
DO NOT
DO NOT
DO NOT
DO NOT
DO NOT
use power tools to construct this product.
tighten screws until parts are assembled or as advised in this guide.
over-tighten tighten screws or bolts.
use this product if parts are missing, damaged or worn.
climb, sit or stand on the product.
CARE INFORMATION
To clean, wipe with a damp clean cloth.
Never use scourers, abrasives or chemical cleaners.
Do not use solvent based cleaners or detergents as they can bleach or damage the product.
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Page 3 of 16
Version 1 - 210818
Parts and Fittings Checklist
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer.
The fittings pack contains small items that should be kept away from children.
6
4
1
2
7
8
9
10
11
12
13
14
14
15
16
17
18
18
19
20
3
5
x3
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Page 4 of 16
Version 1 - 210818
All parts are packed in one carton
Size: 821x 379 x 12 mm
Carton No: 1/1
Description: Base Panel
Qty: 1
Description: LH Side Panel
Qty: 1
Size: 650 x 378 x 15 mm
Carton No: 1/1
Description: RH Drawer Upright
Qty: 1
Size: 598 x 363 x 12 mm
Carton No: 1/1
Carton No: 1/1
456
Qty: 1
Size: 855 x 396 x 15 mm
123
Description: Top Panel Description: RH Side Panel
Qty: 1
Size: 650 x 378 x 15 mm
Carton No: 1/1
Description: LH Drawer Upright
Qty: 1
Size: 598 x 363 x 12 mm
Carton No: 1/1
Description: RH Front Upright
Qty: 1
Size: 650 x 95 x 15 mm
Carton No: 1/1
Plinth :noitpircseD
Qty: 1
Size: 821 x 70 x 15 mm
Description: Front Decor Rail
Qty: 1
Size: 821 x 60 x 15 mm
Carton No: 1/1
Carton No: 1/1
7 8 9
Size: 363 x 60 x 15 mm
Carton No: 1/1
Description: LH Decor Rail
Qty: 1
RH Decor Rail :noitpircseD
Qty: 1
Size: 363 x 60 x 15 mm
Carton No: 1/1
11 1210
Size: 650 x 95 x 15 mm
Carton No: 1/1
Description: LH Front Upright
Qty: 1
Size: 345x 284 x 3 mm
Carton No: 1/1
Description: Drawer Base
Qty: 3
Description: Drawer Cross Rails
Qty: 2
Size: 325.5 x 50 x 12 mm
Carton No: 1/1
Description: Drawer Front
Qty: 3
Size: 326 x 173 x 15 mm
Carton No: 1/1
Carton No: 1/1
16 17 18
Qty: 1
Size: 404.5 x 361 x 12 mm
13 14 15
Description: Adjustable Shelf Description: Door
Qty: 1
Size: 580 x 328 x 15 mm
Carton No: 1/1
Description: Back Panel
Qty: 1
Size: 828 x 604 x 3 mm
Carton No: 1/1
Description: Drawer Back
Qty: 3
Size: 300.5 x 110 x 12 mm
Carton No: 1/1
19 20
Size: 338 x 110 x 12 mm
Carton No: 1/1
Description: Drawer Side
Qty: 6
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Page 5 of 16
Version 1 - 210818
General Hints & Tips
B or E
Tighten
33
G
H
18A
18B
30C
E34
6
4
F
Item QuantityCode
Large Cam Lock
Small Cam Lock
(for Drawer)
Dowel (8x30mm)
Long Cam Bolt
(38mm overall)
Short Cam Bolt
(26mm overall
for Drawer)
Fittings (to scale)
10 20 30 40 50 60 70
80
D34
A or D
28mm
17.5mm
D
A
Stop when
level
Connection Bolt
(M6x25mm)
Screw for fitting
Runner, Hinge and
Anti-tilt Strap
(3 x12mm)
Screw for fitting
Drawer Uprights
to Base Panel
(4x35mm)
A or D
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Page 6 of 16
Version 1 - 210818
Fittings (not to scale)
L
R
QuantityCode
3
L
3M
N
3
3
P
Q
Item
Outer Drawer
Runner - Right
Outer Drawer
Runner - Left
Inner Drawer
Runner - Right
Inner Drawer
Runner - Left
L
R
1K
1
Anti-tilt Strap
R 4
Shelf Support
2J
Door Hinge
Allen Key (4mm)
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 1
STEP 2
For this step:
Tools required
A x2
Fittings required
10
1
12
11
Tighten
B x2 C x2
A x6
B x6
Page 7 of 16
Version 1 - 210818
Cx2
Cx6
Ax2
Ax6
Bx2
C x6
Bx6
Dx4
D x4
i.
ii.
1
1
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 3
STEP 4
For this step:
Tools required
A x10
Fittings required
B x6
C x4
D x4
K
F x3
Page 8 of 16
Version 1 - 210818
Ax3
Ax3
Ax2
Dx2
Dx2
Ax2
Bx3
Cx2
Cx2
Fx3
F
K
Bx3
6
7
7
3
3
2
6
L x3
G x12
M x3
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 5
STEP 6
For this step:
Tools required
Fittings required
C x8
Page 9 of 16
Version 1 - 210818
Cx8
4
4
14
5
5
Gx6
Gx6
Lx3
G
L
Mx3 G
M
Left Side
Panel
Right
Side
Panel
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 7
STEP 8
For this step:
Tools required
C x4
Fittings required
E x4
Page 10 of 16
Version 1 - 210818
Ex4
Cx4
16
G
Q
G x1
Q x1
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 9
STEP 10
For this step:
Tools required
D x2
E x2
B x2
C x2
Page 11 of 16
Version 1 - 210818
Dx2
Cx2
Ex2
Bx2
Ex2
Cx2
8
8
8
9
Fittings required
C x2
E x2
i.
ii.
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 11
STEP 12
For this step:
Tools required
H x4
Fittings required
Page 12 of 16
Version 1 - 210818
Hx4
Ex2
Bx2
Cx2
1
11
10
2
2
6
Fx3
K
B x2
C x2
E x2
F x3
8
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 13
x3
STEP 14
For this step:
Tools required
D x24
Fittings required
E x24
Page 13 of 16
Version 1 - 210818
Dx4
i. ii.
iii.
iv.
v.
Dx4
Ex4
Ex4
Gx4
GG
P
N
G x12
P x3
N x3
N
P
19
17
18 x2
20
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 15
STEP 16
For this step:
Tools required
Fittings required
Page 14 of 16
Version 1 - 210818
R
Rx4
13
Jx2
Gx4
G
G
R x4
J x2
G x8
15
15
Fit Door in Position
On each hinge plate ,
fit x2 screws (G) into
centre of the slots.
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Fittings required
For this step:
Tools required
STEP 17
STEP 18
For this step:
Tools required
Fittings required
Page 15 of 16
Version 1 - 210818
Note: We recommend using the wall strap (Q). This is provided
to avoid accidents and possible fatal injuries if the item falls over
during use. This is for the safety of you and your children or pets
Warning: Always ensure the wall area to be drilled is free of
electrical wires, water and gas pipes. We don't supply wall fixings
as these must suit the wall type of your own home.
If in doubt please consult a qualified trades person.
MAKE SURE UNIT IS LEVEL
IF DOOR NEEDS ADJUSTING, CAREFULLY FOLLOW THESE STEPS
Adjusting door in or out
Adjusting door up or down
Adjusting door left or right
Tighten screws (G) 100% in their final position.
CANYON MULTI UNIT ASSEMBLY INSTRUCTIONS
Page 16 of 16
Version 1 - 210818
Assembly Completed
Your Canyon Multi Unit is now completely asse mbled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Habitat GFW Canyon 1 Door 3 Drawer Sideboard User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI