Freestanding 5x Magnifying LED Lamp 9666
Instructions
Please read carefully before use and retain for future reference.
PARTS
A. Lower pole section
B. Base
C. Flexible neck
D. Lamp head
E. Middle pole section
F. Stem cable
G. Mains adaptor
H. Adaptor jack
I. Adaptor socket
J. On/off button
ASSEMBLY
1. Attach lower pole section (A) to base (B) twist pole
until tight.
2. Position the flexible neck (C) and lamp head (D) so that
it is fully extended and screw onto middle pole section
(E) and tighten.
3. Ensure that any loose stem cable (F) is inserted into
middle pole section (E).
4. Screw the middle pole section (E) into the lower pole
section (A). Take care not to pinch or damage the
cable.
5. Adjust the flexible neck (C) to the desired angle.
6. Insert the adaptor jack (H) into the socket on the
base (I).
7. Plug the mains adaptor (G) into the mains socket and
turn on using the on/off button (J).
USE
• Hold reading material directly parallel to the magnifier
lens. If not positioned correctly, the reading material
may appear distorted.
• The LEDs are specially formulated to simulate the
characteristics of natural sunlight. They are non-
replaceable and should give up to 50,000 hours of use.
• Turn off and unplug the light when not in use.
E
C
D
J
F
A
H
G
I B
WARNING
• Ensure that your mains voltage corresponds to that stated on the unit.
The unit should be connected to an earthed mains socket.
• Use only the adapter supplied.
• Never use the unit if any part is damaged.
• There are no user serviceable parts, if a fault develops, the unit must be
returned to the supplier for repair/replacement subject to guarantee conditions.
• Do not allow the unit to get wet.
• Do not allow the cable to lie on hot surfaces.
• Keep the magnifier away from direct sunlight when not in use.
• Do not look directly at the lit LEDs.
• Route the power cable so that it will not get walked on or pulled (trip hazard).
• Do not allow children to play with this unit, it is not a toy.
• This unit should only be used by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
providing they have been given supervision or instruction concerning use of
the unit by a person responsible for their safety.
• The unit is not intended to be operated by means of an external timer or
separate remote-control system.
CLEANING
• Always switch off and unplug from the mains and allow to cool before
cleaning.
• Wipe clean with a soft dry cloth.
• Do not use any chemical or abrasive cleaners.
TECHNICAL INFORMATION
LED Class: 1
Power supply: DC12V, 120mA
Power output: 1.5W
DISPOSAL
Dispose of all paper, cartons and plastic in accordance with your local recycling
regulations. At the end of the product’s lifespan please dispose of it at an
authorised household waste recycling centre.
DECLARATION OF CONFORMITY
We, The Enterprise Department Ltd.
Of 11 Bridge Street, Bishop’s Stortford, Hertfordshire UK CM23 2JU
in accordance with the following Directive(s):
Electromagnetic Compatibility 2004/108/EC
EN 55015-1:2006+A1:2007+A2:2009
EN 61547:2009
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
Low Voltage Directive 2006/95/EC
EN 61347-2-11:2002
EN 61347-2-13:2006
EN 61347-1:2008+A1:2011
Magnifying LED Floorlamp
Model number: 9666 (FNL-F120448B)
I hereby declare that the equipment named above has been
designed to comply with the relevant sections of the above
referenced specifications. The unit complies with all applicable
Essential Requirements of the Directives.
Mr. Stuart Fowler
Imports Director
August 2013
/
