Haier 51B3Y-N User manual

Available Model：51B3Y-N

Haier Color TV Receiver

Owner's Manual

Please read this manual carefully before operating

the unit, and keep it for future reference.

CONTENTS

Warning and cautions.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ......... 1

Specifications.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ...................2

Preparation. .. .. .. .. .. ..............................................3

Control panel. .. .. .. .. .. ......................................... .. . 4

Remote control board.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .............. 5

6

Select channel and store.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ...........

Picture set. .. .. .. ........................................... .. .. .. . 8

Sound set. .. .. .. .. ........................................... .. .. .. 9

Feature set. .. .. .. .. ...............................................

10

Converge set.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ................ .......11

Basic operation. .. .. .. .. ........................................... 12

External connection. .. .. .. .. ........................................14

Trouble shooting guide.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ......16

1

War ning and Cautions

Maintenance:

1. When you clean the TV set, please pull out the power plug from AC outlet. Don't

clean the cabinet and the screen with benzene, petrol and other chemicals.

2. In order to prolong the using life of the TV set, please place it on a ventilated

place.

3. To prevent the TV set from firing or electric shock, don't expose the TV set to rain

or moisture.

Cautions

1.Don't place the power wire near heater and press it, when you insert or

remove the power wire, please hold the body of plug.

2.Overload will damage the TV set or cause electric shock, so when you use

the socket or outlet line on the wall, don't overload.

3. Don't open the back cover at random, otherwise it is possible to damage the

components in the TV set and harm you.

4. When the TV set is in thunder and lightening or it isn't going to be used for a

long time , please pull out the plug from AC outlet and the antenna plug from the

back cover of the TV set.

Cautions to use VGA

1.The display brightness of TV set is much higher than the computer's,in

order to protect your eyes, please keep a certain distance with the screen

when you use it, and adjust the brightness and contrast of TV set to be

proper.

2.When you connect the VGA output terminal of computer or other devices,

please set the display format of computer to 640x480 pixel and the brush

frequency of monitor to 60Hz. When the display format is above 640x480

pixel or brush frequency is above 60Hz, the TV set will not display the

picture correctly, the screen displays "OUT OF RANGE. SET 640x480

60Hz". Because different display card is different, when you use VGA

terminal to receive computer output signal, the picture and size may be

different, and the edge line of picture may not be straight, but it will not

have an effect on watching normally.

2

Specifications

The specifications offered you here are only for reference and, with the improvement

of the products ,there may be some different between the description and the practicality.

AC 180V-250V 50Hz/60Hz

51 B3Y- N

PAL 、 NTSC、SECAM

D/K、I、B/G、M

Main audio 10W+10W

250W

111.5（Width）X50.0（Depth）X133.6（Height）（cm）

Three of 7”red,green,blue picture tubes(the viewable minimal dimension is 126cm)

Picture tube

M o d e l

Colour system

Sound system

Sound output power

Power requirements

Power consumption

Net dimension

Accessories

Remote control X1

Owner's manual X1

X2

Battery

Environment conditions

Working temperature

Working humidity

Storage temperature

Storage humidity

NOTE

Design and specifications are subject to change without notice.

The dimension in this manual is an approximation.

UHF

VHF

S-VIDEOS-VIDEO

VIDEOVIDEO

YY

LL

RR

CbCb

PbPb

CrCr

PrPr

ININ

OUTOUT

LL

AUDIOAUDIO

RR

AVAV11

AVAV22

AVAV

AUDIOAUDIO

VIDEOVIDEO

VGAVGA

3

Preparation

1.Antenna connection

Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV

system or an outdoor antenna. In different places, the suitable antenna type and position

are different.

Antenna adapter

(additional purchase)

75 coaxial cable

Plug

(additional purchase)

AC power socket

Antenna input

（75 standard coaxial type）

Mixer

（additional

purchase）

300 twin-lead cable

Note：

It is recommended that you'd better use 75

Don't bind antenna cable and electric wire together.

If the connects to the , please remove its plug from the

antenna terminal socket w

coaxial cable to remove the disturbance

caused by airwave.

indoor antenna TV set

hen you use the outdoor antenna.

2.Preparation for the remote control

Batteries placement:

1.Remove the batteries cover.

2.Insert two size AAA batteries and match the +/-polarities of the battery to the +/- marks

inside the battery compartment.

Note:

(1)Do not drop, dampen or dismantle the remote control.

(2)When the remote control will not be used for a long period of time or when the batteries

are worn out, remove the batteries to prevent leakage or damaging the remote control.

(3)Replace two old batteries at the same time, don't charge the batteries.

(4)Don't use the charge batteries(Ni-Cd) or different types of batteries.

(5)Do not throw the batteries into a fire. Dispose of used batteries in the specified manner.

VGA

Y

R

OUT

IN

Y

L

Cb

L

Pb

Pr

S-VIDEO

Cr

IN

R

VIDEO AUDIO

VIDEO

AV

AV2

AV1

S-VIDEOS-VIDEO

VIDEOVIDEO

YY

LL

RR

CbCb

PbPb

CrCr

PrPr

ININ

OUTOUT

LL

AUDIOAUDIO

RR

AVAV 11

AVAV 22

AVAV

AUDIOAUDIO

VIDEOVIDEO

VGAVGA

4

MENU

TV/AV

_

V

V+

_

P

P+

Control Panel

1.Front Control Panel

Main power switch: pressing this button to connect

the power supply, the power indicator will light.

Pressing this button again, the power supply of

this TV set will be cut off.

Main power switch button

Power indicator

TV/AV selection button

Menu button

Volume up/down button

Program up/down button

VGA input terminal

Antenna input terminal

Video input terminal

Audio input terminal

AV1 input terminal

AV2 input terminal

AV output terminal

S-VIDEO input terminal

2.Rear Control Panel

5

Remote Control Board

1

4

7

YPbPr

SLEEP

V-

STILL

DISPLAY

P.MODE

LANGUAGE

4

5

6

7

8

9

1010

3

2

11

C.SYS

2

3

5

6

8

9

0

MENU

RECALL

P+

P-

V+

POWER

TV/AV

NICAM

MUTE

S.MODE

SCAN

HYF- 33L

11

12

13

14

15

16

17

18

19

20

22

1

2

3

4

7

8

12

14

17

18

19

6

9

1010

13

15

14

16

5

20

21

5

22

MUTE: Press to temporarily cut

off the sound

0~9 DIGIT: One digit selection buttons

POWER: Turns the TV on/off

TV/AV:TV/AV switch.

SLEEP: Press to select a preset time

MENU: Single button menu cycle selection

P+/-:Program switch or up/down

selection of menu.

V+/-:Volume is up/down or carry out

the menu

NICAM: Nicam button

P. MODE:Picture mode

DISPLAY: Display button

YPbPr: Y/Pb/Pr switch

LANGUAGE: Language selection button

S. MODE: Sound mode

-/--/---: One/Two/Three digital button

SCAN: Scan button

21

1011

STILL: Still button

-/--/---

S.SYS

NR

VGA

C.SYS: Color system

RECALL: Recall button

S.SYS: Sound system

NR: Noise reduction

VGA: VGA switch button

6

Select Channel and Store

1. Preparation for Selecting Channels

Connect the antenna(or cable signal wire)and

power supply wire, then press the power switch,

after the power indicator is on, the picture of

TV set will appear in a few seconds.

2. Auto Search

After the auto search is finished, the best

position will memory in every program orderly,

we recommend using auto search when you use

it for the first time and set the present program

to 0 before searching.

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select AUTO, press

V+ /- button to start searching until all the

programs are searched completely, then the

starting program number will display on the

screen, it is as figure2.

Note: During auto search, you can press V+/-

button on the remote control at any time to stop

searching.

3. Manual Search

You can arrange programs as you need.

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+/ -button to enter the next menu.

(3)Press P+ /-button to select MANUAL, press

V+ /-button to start searching, every time you

search the signal, it will stop, this signal is

stored on this channel. If this signal is not you

need, you can press V+ /-button to go on

searching until you search the signal you need,

it is as figure3.

4. Fine Tune

If the receiving effect is not good, you can use

Fine Tune to improve the quality of picture and

sound.

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select FINE, press

V+ /-button to fine tune until the picture and

sound are best, then press MENU button to

exit, it is as figure4.

Note: "?"in the menu is the help instruction of

operation.

PICTURE BRIGHT

SOUND COLOR

FEATURES CONTRAST

INSTALL SHARP

TINT

P.MODE

INCR.PIC

NR

VM

(Figure1)

INSTALL

CHANNEL

BAND

SKIP

.

CH SWAP

C

.

SYSTEM

.

S SYSTEM

FINE

MANUAL

AUTO

289.

25MHz

(Figure2)

INSTALL

CHANNEL

BAND

SKIP

.

CH SWAP

.

C SYSTEM

.

S SYSTEM

FINE

AUTO

289

MANUAL

25MHz

.

(Figure3)

INSTALL

CHANNEL

BAND

SKIP

.

CH SWAP

C SYSTEM

.

S SYSTEM

MANUAL

AUTO

25MHz

.

289

FINE

(Figure4)

? MOV: P+ P- SEL: V+ EXIT:MENU

? MOV: P+ P- ADJ: V+ V- EXIT: MENU

? MOV: P+ P- ADJ: V+V- EXIT:MENU

7

Select Channel and Store

5.Band

When it is in manual search, the signal you

want to search is not on the present band, you

can change the band to improve the speed of

searching.

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select BAND, then press

V+ /-button continually, the signal band is

switched among VHFL-VHFH-UHF. You can

select the band you want, it is as figure5.

6. Skip

After pre-tuning the channel, you can skip the

channel number you don' t need, such as

repeat signal, false signal and so on, so you

can select the channel you want to watch.

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select CHANNEL, it is

as figure6.

(4)Press V+ /-button to skip the channel number

you need.

(5)Press P+ /-button to select SKIP, it is as

figure7.

(6)Press V+ /-button to preset SKIP ON mode.

Note: When a certain channel is in SKIP ON

mode, this channel will not appear when you

select program by pressing P+/-button,but this

channel will appear by pressing the digital select

button.

7. Change Swap

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select CH.SWAP, press

V+ button to enter the next menu, it is as figure8.

(4)Press P+ /-button to select FROM, then

press V+button to select the present channel.

(5)Press P+ /-button to select TO, then press

V+ button to set the channel you need.

(6)Press P+ /-button to select EXCHANGE,

then press V+button to finish exchanging.

INSTALL

CHANNEL

SKIP

.

CH SWAP

C SYSTEM

.

S SYSTEM

.

FINE

MANUAL

AUTO

VHFL

BAND

(Figure5)

INSTALL

BAND

SKIP

.

CH SWAP

.

C SYSTEM

S SYSTEM

.

FINE

MANUAL

AUTO

CHANNEL 0

(Figure6)

INSTALL

BAND

.

CH SWAP

.

C SYSTEM

S

.

SYSTEM

FINE

MANUAL

AUTO

ON

SKIP

CHANNEL

(Figure7)

INSTALL

BAND

SKIP

.

C SYSTEM

S SYSTEM

.

FINE

MANUAL

AUTO

.

CH SWAP

CHANNEL

(Figure8)

=

? MOV: P+ P- ADJ: V+ EXIT:MENU

? MOV: P+ P- ADJ: V+V- EXIT:MENU

8

Select Channel and Store

8.Color System

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select C. SYSTEM, then

press V+/ -button continually, the color system

will switch among AUTO-PAL443-NTSC358-

SECAM-NTSC443- PALM-PALN- PAL60, it is as

figure9.

9. Sound System

(1)Press MENU button to make the screen

display the menu as figure1.

(2)Press P+ /-button to select INSTALL, then

press V+button to enter the next menu.

(3)Press P+ /-button to select S.SYSTEM, then

press V+/ -button continually, the sound system

will switch among AUTO DK BG I-M, it is as

figure10.

1. Simulative Value Adjustment

(1)Press MENU button, then press P+/-button

to select PICTURE, it is as figure11.

(2)Press V+ button to enter the next menu.

(3)Press P+ /-button to select BRIGHT, COLOR,

CONTRAST, SHARP or TINT that you need to

adjust.

(4)Press V+ /-button to adjust the stimulative

value of BRIGHT, COLOR, CONTRAST, SHARP

or TINT.

Note: TINT is only valid in NTSC system.

2. Picture Mode

(1)Press MENU button, then press P+/-button

to select PICTURE, it is as figure11.

(2)Press V+ button to enter the next menu.

(3)Press P+ /-button to select P.MODE, it is as

figure11. Then press V+ /- button, the picture

mode will switch among SOFT-NATURE-RICH-

USER.

3. INCR.PIC

(1)Press MENU button, then press P+/-button

to select PICTURE, it is as figure11.

(2)Press V+ button to enter the next menu.

(3)Press P+ /-button to select INCR. PIC, then

press V+/ -button to set the INCR.PIC ON or

OFF, it is as figure13.

Picture Set

INSTALL

CHANNEL

BAND

SKIP

.

CH SWAP

S

.

SYSTEM

FINE

MANUAL

AUTO

.

C SYSTEM AUTO

(Figure9)

INSTALL

CHANNEL

BAND

SKIP

.

CH SWAP

.

C SYSTEM

FINE

MANUAL

AUTO

S SYSTEM

.

AUTO

(Figure10)

PICTURE BRIGHT

SOUND COLOR

FEATURES CONTRAST

INSTALL SHARP

TINT

P.MODE

INCR.PIC

NR

VM

(Figure11)

BRIGHT

COLOR

CONTRAST

SHARP

TINT

INCR.PIC

NR

VM

P.MODE USER

(Figure12)

PICTURE

BRIGHT

COLOR

CONTRAST

SHARP

TINT

P.MODE

NR

VM

INCR.PIC ON

(Figure13)

PICTURE

? MOV: P+ P- SEL: V+ EXIT:MENU

? MOV: P+ P- ADJ: V+V- EXIT:MENU

11

Converge Set

4. Converge Adjustment

There are red, green and blue picture

projection tubes in this projection TV, the

picture that they send out separately will mix

in all kinds of color in a certain space position,

then they project on the on-screen display and

become a complete picture, because the red,

green, and blue is sent out by three projection

tubes separately, beam of light must be adjusted

exactly. But the converge may cause a certain

excursion. If you find there is color ring or

aperture on the edge of picture when you watch

TV, so you should adjust the converge, there

is 9 points converge adjustment offered in this

TV set.

Adjustment Steps:

1.Receive PAL system program.

2.Enter 9 points converge.

(1)Press MENU button to display the main

menu, then press P+/ -button to select

FEATURE, it is as figure20.

(2)Press V+ button to enter the next menu.

(3)Press P+ /-button to select CONVERGE, it is

as figure23, then press V+button to enter user

adjust 9 points converge menu, it is as figure24,

please follow the screen cue to operate.

3. Adjustment Contents

(1)Press MENU button to select the color you

need adjust( Green is standard, you can adjust

red and blue), then press P+/-button, V+/ -

button to adjust converge to make the red cross

and blue cross is in the same position.

(2)Press STILL(ST), DISPLAY(DS), SCAN

(SC) , NICAM( NI) button on the remote control

separately to move the cursor to the surround

point, and adjust the red and blue converge to

make them in the same position.

(3)Press RECALL button on the remote control

to save the data after all the contents are

adjusted well, then press 0 button to exit

converge adjust status, and you can watch the

TV programs. The 9 points converge adjusted

can reposition to the ex- work status according

to your need, you can press LANGUAGE button

on the remote control on the 9 points converge

menu, then press 0 button to exit.

(4)If the converge is slightly bad when you

receive NTSC system and YPbPr, VGA signal,

you can also follow the above steps to adjust.

(Figure23)

FEATURES

LANGUAGE

TIMER

LOCK

CONVERGE

=

USER ADJUST RED

EXIT: 0

MOVE: ST, DS, SC, NI

ADJU: P+, P-,V+,V-

COLO: MENU

SAVE: RECALL

REST:LANGUAGE

(Figure24)

? MOV:P+ P- SEL:V+ EXIT: MENU

13

Basic Operation

system, sound system and time set on the

screen, press this button again to cancel.

11.Program Scan

Press SCAN button on the remote control to

scan all the stored TV programs automatically,

during scanning, you can press SCAN button to

stop. (you can also press other any button)

12.Nicam Selection

When you receive the TV programs with Nicam,

you can press NICAM button on the remote

control to enter Nicam status.

13.Mute Set

Press MUTE button on the remote control to

cancel the sound completely, press this button

again to recover the original volume.

1

2

3

4

5

6

7

8

9

0

-/--/---

V-

V+

MENU

P-

P.MODE

S.MODE

STILL SCAN

DISPLAY NICAM

LANGUAGE MUTE

VGA

Y

R

OUT

IN

Y

L

Cb

L

Pb

Pr

S-VIDEO

Cr

IN

R

VIDEO

AUDIO

VIDEO

AV

AV2

AV1

S-VIDEOS-VIDEO

VIDEOVIDEO

YY

LL

RR

CbCb

PbPb

CrCr

PrPr

ININ

OUTOUT

LL

AUDIOAUDIO

RR

AVAV 11

AVAV 22

AVAV

AUDIOAUDIO

VIDEOVIDEO

VGAVGA

14

External Connection

The Method to Connect Video and Audio Input

You can connect the VCR or Pickup Camera to the TV to enjoy a higher quality of picture effect. If the

Video equipment is with S-VIDEO output terminal, connect to the S-VIDEO input terminal of this TV

set,If without, connect to the video input terminal. When the video equipment is DVD, you can

connect the YCbCr,YPbPr output of DVD to the YCbCr,YPbPr input of TV set. When the video

device is computer or devices with VGA output, you can connect the VGA output to the VGA input

terminal of this TV set, so that you can receive high quality picture.

Antenna input terminal

Video input terminal

Audio input terminal

AV1 input terminal

AV2 input terminal

AV output terminal

S-VIDEO input terminal

T

b

i

gh n

ss

) o

u

p t

(

Y

o r t

e t u

VGA input terminal

T r d

o

n

t

o

(Cr/P

o

e c m

po en utp

u

t

r)

oT

o b

lu

e

c

omp

nen

t

ou

t

p

u

t

(

C

b

/

Pb)

T

o

a

u

d

io

(le

f

t)o

u

p tt u

T

a

d

i

o

(

r t

)

ou p

t

o u igh

t

u

-

tT

o S VIDEO

outp

u

te

rm

ina

l

T a dio

(l

e

ft)o

u

p to

u

t u

T

o a

udio

(

r

i

ht

)

ou

tp

u

tg

To audio, video input

a

d

,

e

u

T

o

u

i

o

vid

o in

p

t

T

o

a

d

i

o,

v e

in

uu

id

o p

t

T

a

di

o

(

l f

) u p

o u e t

o t

ut

a

( )

u

p

T

o

u

d

i

o rig

h

t o

t ut

v t

u

T

o

ide

o

ou

p

t

DVD/HDTV

VCR with S-VIDEO terminal

VCR without S-VIDEO terminal

Note:

1.When DVD video broadcasts, connect to interlace component video signal (YCbCr) or progressive

component video signal(YPbPr)terminal according to broadcasting equipment.

2.When HDTV video broadcasts, connect to YPbPr terminal, and select corresponding status (480p/60Hz or

1080i/60Hz)according to broadcasting form.

S-VIDEOS-VIDEO

VIDEOVIDEO

YY

LL

RR

CbCb

PbPb

CrCr

PrPr

ININ

OUTOUT

LL

AUDIOAUDIO

RR

AVAV11

AVAV22

AVAV

AUDIOAUDIO

VIDEOVIDEO

VGAVGA

VGA

Y

R

OUT

IN

Y

L

Cb

L

Pb

Pr

S-VIDEO

Cr

IN

R

VIDEO AUDIO

VIDEO

AV

AV2

AV1

15

Connect video,audio output, VGA input

1. You can record the output audio,video signal of TV set through VCR or use as other function.

2.Connect the output VGA signal of computer to VGA input terminal of TV set and take as display.

External Connection

To video, audio input

iTo v de

o

in

p

u

t

tT

o

a

ud

i

o(

left

)

i

np

u

To

a

udi

o(

ri

g

h

t) in

put

VCR and other videorecord devices

VGA input terminal

Antenna input terminal

Video input terminal

Audio input terminal

AV1 input terminal

AV2 input terminal

AV output terminal

S-VIDEO input terminal

Audio input

T

V

GA

n ut

o

i p

Computer main frame

16

The following problems are not always caused by hardware failure, please use the follow

trouble shooting guide before you call for service:

Note:1.If the problem can not be fixed after you check above items. DO NOT attempt

to remove the back cover by yourself.

2.If the snapping sound from the cabinet of the TV set can be heard occasionally

because of temperature changing of environment, it is normal, you can use it

reassuringly.

BREAKDOWN PHENOMENON

PICTURE

SOUND

CHECKING

The direction and connection of the antenna.

Direction station of the

antenna

and

Interference from electric

appliance. Automobile、Motor,

Vehicle Fluorescence lamp etc.

Volume, Sound mute

The power plug isn't plugged in AC

outlet. The main power isn't turned

on. The setting up of contrast, brig-

htness and volume.

Adjust color control

Adjust channel again

?

Picture with Snow

No Color

No Picture

Normal

Disturb

Double or Triple Image

Noise

Normal

Noise

No Sound

Normal Volume

Normal or Weak Volume

??

Scramble

If you use cable TV,please check if its

intensity of output signal is fit for standard

(60dB-74dB), if not, please contact with

the local TV station.

Lose Control

Remove the power plug, then connect

the power again after 10 seconds to

see if avoid, if not, please contact the

local service department.

TROUBLE SHOOTING GUIDE

17

Accessory Page Instruction

After taking out the projection TV, in order to prevent block of the TV set

from gliding, please put antiskid cushion on the four blocks of TV set as

figure to prevent the TV set from gliding at random.(see figure1,2.3)

Figure1

Block of TV set

Antiskid cushion

Block of TV set is matched with

antiskid cushion

Figure2

Figure3

Made in China

0090506720

Page is loading ...

Haier 51B3Y-N User manual

Haier 51B3Y-N User manual

Related papers

Other documents