Sierra PDM-U Driver Quick Installation Guide

Sierra
Brand
Sierra
Model
PDM-U Driver
Type
Quick Installation Guide

Sierra PDM-U Driver

Sierra PDM-U Driver is a cable driver designed for use with RedySmart Series devices. It is compatible with Windows XPTM, Windows VistaTM, and Windows 7TM operating systems. The driver is developed by FTDI and certified by Microsoft WHQL.

This driver allows you to connect your RedySmart device to your PC via a USB port. It provides a communication channel between the device and the RedySmart Smart Interface Portal (SIP) software, enabling you to control and configure your device from your PC.

Once the driver is installed, you can connect your RedySmart device to a COM port using the PDM-U cable. You can then launch the RedySmart SIP software and use it to find and connect to your device. The software allows you to view device information, configure settings, and perform various operations on your device.

Sierra PDM-U Driver

Sierra PDM-U Driver is a cable driver designed for use with RedySmart Series devices. It is compatible with Windows XPTM, Windows VistaTM, and Windows 7TM operating systems. The driver is developed by FTDI and certified by Microsoft WHQL.

This driver allows you to connect your RedySmart device to your PC via a USB port. It provides a communication channel between the device and the RedySmart Smart Interface Portal (SIP) software, enabling you to control and configure your device from your PC.

Once the driver is installed, you can connect your RedySmart device to a COM port using the PDM-U cable. You can then launch the RedySmart SIP software and use it to find and connect to your device. The software allows you to view device information, configure settings, and perform various operations on your device.

PDM-U Driver Quick Install Guide
RedySmart
®
Series
1 | RedySmart_v2_2020
Installation
To install the drivers for an FTDI device follow the two steps below.
  Note Please connect the PDM-U cable with your PC after you successfully installed the drive.
STEP 1. Install Driver
1. Download the driver from our website at sierrainstruments.com/redy-driver.
2. Double click on CDM20814_Setup.exe file and the installation routine for the USB serial-converter will start automatically. If a device
of the same type has been installed on your machine before and the drivers that are about to be installed are different from those, the
original drivers may need to be uninstalled first.
  Note If you use Windows 7 and connect the PDM-U cable to a COM port, Windows 7 automatically starts to download the driver
from the internet. If you prefer to proceed in this way, then continue with Step 2. Make sure internet connection is available.
3. After double clicking the setup, the dialog in Figure 1 appears, which describes the installation process. If this process finishes without an
error, the driver is installed on your PC. On very fast computers the installation process is hardly recognizable.
This document describes the installation process for the
RedySmart PDM-U cable driver. The driver can be used for the
following operating systems.
• Windows XP
TM
• Windows Vista
TM
• Windows 7
TM
The driver is developed by FTDI and certified by Microsoft WHQL.
For further information visit the FTDI website. You can download the
driver from our website at sierrainstruments.com/redy-driver
For complete instructions, please download and read the
RedySmart Series Instruction Manual.
Figure 1: CDM20814_Setup.exe (USB Serial Convert driver) installs the driver
2 | RedySmart_v2_2020 99-2173
5 Harris Court, Building L / Monterey, CA 93940 / USA
USA: 800.866.0200 / 831.373.0200
Europe: +31.72.5071400
China: +8621 5879 8522
Email: [email protected] or [email protected]
For global locations, visit: sierrainstruments.com/locations
www.sierrainstruments.com
CONTACT SIERRA
STEP 2. Get communication with the RedySmart device via RedySmart Smart Interface Portal (SIP) software
1. If the driver is successfully installed, you can connect a RedySmart device with the PDM-U cable to a COM port. Then start the get
RedySmart SIP software.
  Note Keep in mind that for each physical USB port a logical COM port is assigned. This means if you connect the PDM-U cable to
another port as before, a new port will be initialised.
The COM port has to be properly chosen in the RedySmart SIP in order that the communication with the device can be built up.
2. To chose the proper COM port you have to use the combo box in Figure 2 (1. COM port). If you click on the blue question mark in
RedySmart SIP, the Windows device manager opens and you can see the COM port to which the PDM-U cable is connected to.
3. Click on the button [Start search] to find the connected RedySmart devices. If connected devices show up with serial number in the lower
part of the window, the driver has been installed properly and the correct COM port has been assigned.
You may find the connection process explained in more detail in the RedySmart SIP manual.
Figure 2: Configure the COM parts
* Windows XP, Windows Vista and Windows 7 are registered trademarks or trademarks of the Microsoft Corporation
in the USA and / or other countries.
Opens device manager
1. COM Part
2. Search Devices
  Note For some operating systems, it might be necessary to restart your computer in order to get the
driver operating with RedySmart SIP.
  • Page 1 1
  • Page 2 2

Sierra PDM-U Driver Quick Installation Guide

Sierra
Brand
Sierra
Model
PDM-U Driver
Type
Quick Installation Guide

Sierra PDM-U Driver

Sierra PDM-U Driver is a cable driver designed for use with RedySmart Series devices. It is compatible with Windows XPTM, Windows VistaTM, and Windows 7TM operating systems. The driver is developed by FTDI and certified by Microsoft WHQL.

This driver allows you to connect your RedySmart device to your PC via a USB port. It provides a communication channel between the device and the RedySmart Smart Interface Portal (SIP) software, enabling you to control and configure your device from your PC.

Once the driver is installed, you can connect your RedySmart device to a COM port using the PDM-U cable. You can then launch the RedySmart SIP software and use it to find and connect to your device. The software allows you to view device information, configure settings, and perform various operations on your device.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents