EK Water Blocks EK-FC780 GTX DCII User manual

Brand: EK Water Blocks

Model: EK-FC780 GTX DCII

Category: Computer liquid cooling

Type: User manual

EK Water Blocks EK-FC780 GTX DCII is a high-performance water block engineered specifically for the GeForce 780 GTX DCII series graphics cards. Designed for expert users, it efficiently cools your GPU, memory, and VRM, allowing for stable and reliable operation even during intense gaming sessions or overclocking. The EK-FC780 GTX DCII features a robust construction, pre-installed 2.5mm standoffs, and includes all necessary mounting hardware for a straightforward installation process.

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 12

of August, 2013. Revision 1.0

Installation and mounting manual for EK-FC 780 GTX DCII Original CSQ

water block

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.

4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of GeForce 780 GTX DCII series graphics card.

STEP 2: PREPARING YOUR GRAPHIC CARD.

1. REMOVING STOCK COOLER: Remove encircled screw on the

bracket (required only on certain models):

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

1 cont.. REMOVING STOCK COOLER. Remove the stock GPU HSF assembly. Remove all encircled

screws attaching the backplate and VRM heatsink to the circuit board as well as two screws attaching the

I/O bracket to the HSF.

2. CLEANING THE PCB. Carefully detach the original stock cooler

after removing all

screws securing it to the board. Wipe off the

remains (by using non–abrasive cloth or

q-tip

, as shown on sample

photo) of the original thermal compound until the components and

circuit board are completely clean. EKWB recommends the use of

denatured alcohol for removing TIM leftovers.

3. APPLYING THERMAL COMPOUND.

Wipe off the

remains (by using non–abrasive cloth or

q-tip

) of the

original thermal compound until the components and

circuit board are completely clean. Apply thermal

compound: lightly coat

NVIDIA

GPU chip with enclosed

EK-TIM Ectotherm thermal grease. EKWB recommends to

apply thermal grease in cross form for best performance

(see sample picture).

4. CUTTING THERMAL PADS.

Your block comes with thermal pads, some of which are already pre-cut. Others

have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers. PLEASE

REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.

Replacement thermal pads: Thermal Pad D – 0.5mm (RAM 8x), Thermal Pad B – 0.5mm (75x50mm)

STEP 3: INSTALLING THE WATER BLOCK

1. PLACING THERMAL PADS ON PCB.

Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than

enough pads to cover all surfaces that need to be covered to make block fully functional). EKWB recommends using small drops of electrically non-conductive (for

example: EK-TIM Ectotherm, Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme™) thermal grease on each phase regulator (that is being covered with thermal pad) in

order to even further improve the thermal performance of the EK-FC 780 GTX DCII Original CSQ series water block.

1: Thermal pad D – 0.5mm

(for memory IC):

2: Thermal pad B – 0.5mm

(for VRM/MOSFET):

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 12

of August, 2013. Revision 1.0

2. PLACING THE BLOCK TO THE GRAPHICS CARD

. Carefully position the water

block with preinstalled 2.5 mm standoffs on to the graphics card. During this process

please make sure you align mounting holes on the PCB with holes on the water block.

Also pay attention not to use too much force by pressing block down to PCB. Chip dies

are prone to cracking.

3. ATTACHING BLOCK TO THE GRAPHIC CARD

. Use a Philips screwdriver screw in

enclosed M3x4 DIN 7985 screws. EKWB recommends users to start tightening the

screws around the GPU core and continue outwards.

STEP 4: CHECKING FOR CONTACTS

If necessary temporarily r

emove the water block to check for uniform surface contact between the block and the components, pay special attention to the VRM section of the

graphics card. Check whether the water block makes contact with the intended integrated circuit. Then repeat sub-steps in previous section to re-attach the block. In case you

fail to obtain good contact, please check again your thermal pad thickness or contact our support service at http://www.ekwb.com/support.

STEP 5: INSTALLATION OF FITTINGS AND TUBING

Screw in the fittings in the G1/4 threaded openings on plastic top of the water block. EKWB recommends using EK-PSC fittings with the EK-FC780GTX Original CSQ

series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an appropriate substitute. You can use any opening as an

inlet/outlet port.

INSTALLING EK-FC LINK:

Alternatively you can install the enclosed EK-FC Link which allows installation of both EK-FC Bridge system as well as the use of G1/4 threaded fittings.

Please remove the middle M4x8 DIN 7984 screw, install the EK-FC Link together with OR 14x1.5 mm gaskets and secure it with enclosed M4x25 DIN 7985 screw. Use enclosed

2.5 mm Allen (hex) key!

Once installed you can install two (preferably angled) G1/4 threaded fittings or any EK-FC Bridge CSQ series interconnect (

serial

parallel

STEP 6: INSERTING THE CARD IN YOUR PC CASE

Carefully lift your graphics card with installed block and insert it in your PC’s motherboard PCI-express expansion slot. Please bear in mind that your graphics card is probably

heavier than when it was equipped with original heat sink fan assembly. One needs to be very careful when handling the graphics card. Avoid all un-needed manipulation of the

VGA/water block assembly that might damage your card or water block during final installation.

REQUIRED TOOLS:

scissors Philips head screwdriver thermal grease

Screw M3x4 DIN 7985

EK-PSC Fitting

Water block top

M4x25 DIN 7984

Tubing

OR 14x1.5 mm

EK-FC Link