Geovision GV-3D User manual

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

User's Manual V1.02

GV-3D People Counter

3DPCV102-A

Under the copyright laws, this manual may not be copied, in whole or in part,

without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is

accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind

and assumes no responsibility for errors or omissions. No liability is assumed

for incidental or consequential damages arising from the use of the information

or products contained herein. Features and specifications are subject to

change without notice.

GeoVision, Inc.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335

http://www.geovision.com.tw

Trademarks used in this manual: GeoVision, the GeoVision logo and GV

series products are trademarks of GeoVision, Inc. Windows and Windows XP

are registered trademarks of Microsoft Corporation.

October 2013

Contents

Contents .............................................................................................................................. i

Firmware and Software Compatibility............................................................................... iii

Chapter 1 Introduction ..................................................................................................... 1

1.1 Features .................................................................................................................. 2

1.2 Packing List ............................................................................................................. 2

1.3 Hardware Requirements.......................................................................................... 2

1.4 Options.................................................................................................................... 3

1.5 Overview ................................................................................................................. 4

1.5.1 Front View ................................................................................................ 4

1.5.2 Rear View................................................................................................. 5

1.6 The IR Remote Control............................................................................................ 6

Chapter 2 Getting Started................................................................................................. 8

2.1 Connecting the Device............................................................................................. 8

2.2 Restoring to Factory Default Settings ...................................................................... 9

2.3 Installing Wall Mount (Optional) ..............................................................................10

2.4 Installing VESA Monitor Mount (Optional) ...............................................................11

2.5 Installing In-Ceiling Mount (Optional) ......................................................................12

Chapter 3 The OSD Menu................................................................................................16

3.1 Setting the Network ................................................................................................17

3.2 Setting the GV-3D People Counter .........................................................................18

3.3 Adjusting Device Time ............................................................................................19

Chapter 4 The Web Interface...........................................................................................20

4.1 Accessing the GV-Web Report Lite.........................................................................20

4.2 Setting the GV-3D People Counter .........................................................................21

4.2.1 General Settings......................................................................................22

4.2.2 People Counter Settings ..........................................................................27

4.2.3 Report to Other Servers...........................................................................28

4.3 Accessing People Counting Data............................................................................29

4.3.1 Device .....................................................................................................29

4.3.2 Group ......................................................................................................31

4.3.3 Log ..........................................................................................................33

4.3.4 Query.......................................................................................................34

Chapter 5 Content Designer............................................................................................37

5.1 Minimum System Requirements .............................................................................37

5.2 Installing the Content Designer...............................................................................38

i

5.3 Creating a Screen Layout .......................................................................................39

5.4 Exporting the Screen Layout to GV-3D People Counter..........................................41

Chapter 6 GV-IP Device Utility.........................................................................................42

6.1 Installing GV-IP Device Utility .................................................................................42

6.2 Setting the GV-3D People Counter .........................................................................43

Specifications.....................................................................................................................45

GV-3D People Counter ...................................................................................................45

Asus Xtion Pro / Asus Xtion Pro Live...............................................................................46

Appendix ............................................................................................................................47

Optimal Installation..........................................................................................................47

Detection Limitations.......................................................................................................48

ii

iii

Firmware and Software Compatibility

The Asus Xtion Pro / Asus Xtion Pro Live and GV-Web Report compatible with GV-3D People

Counter V1.01 and V1.02 are listed below

Models Asus Xtion Pro /

Asus Xtion Pro Live

GV-Web Report

GV-3D People Counter V1.01

V5.3.26 and V5.7.9

GV-3D People Counter V1.02

V5.7.9 and V5.8.22

V2.2.3.0 or later

Introduction

1

Chapter 1 Introduction

The GV-3D People Counter integrates Asus Xtion Pro / Asus Xtion Pro Live to count and

analyze the number of people passing by the designated detection area. You can connect the

GV-3D People Counter with a VGA or HDMI monitor for direct display of counting data and

configuring device settings through on-screen display (OSD) menu. GV-3D People Counter

comes with a built-in Web interface, the GV-Web Report Lite, for easy setup and looking up

people counting data.

H

D

M

I

/

V

G

A

USB

GV-3D People Counter

I

n

t

e

r

ne

t

Asus Xtion Pro /

Asus Xtion Pro Live

Display Monitor

GV-Web Report Lite

or GV-Web Report

Infrared sensor to

detect people

Counting data and charts

Live people counts

Figure 1-1

1

2

1.1 Features

 Counts the number of people (In and Out)

 Support for HDMI and VGA compatible monitors

 IR remote control to configure on-screen display (OSD) menu

 GV-Web Report Lite: Web interface to look up people counting data and charts

 Support for data compiling and chart analysis on GV-Web Report

 Audio alarm for traffic in wrong direction and exceeding maximum entries, exits or stays

 Content Designer to customize layout on display monitor

 SDHC card supported

1.2 Packing List

1. GV-3D People Counter × 1

2. IR remote control × 1

3. AC / DC adapter × 1 (12 V / 3 A, 36 W)

4. SD card x 1

5. Power cord x 1

6. Software CD x 1

1.3 Hardware Requirements

In order to detect people, GV-3D People Counter must be integrated with an Asus Xtion Pro or

Asus Xtion Pro Live of the following firmware versions. Asus Xtion Pro Live is available for

purchase as an optional device.

 GV-3D People Counter V1.01: Asus Xtion Pro or Asus Xtion Pro Live V5.3.26 and V5.7.9

 GV-3D People Counter V1.02: Asus Xtion Pro or Asus Xtion Pro Live V5.7.9 and V5.8.22

In addition, the Asus Xtion Pro / Asus Xtion Pro Live must be installed at a location where it

will not be exposed to direct sunlight or IR LED.

Introduction

1

1.4 Options

Optional devices can be purchased separately for GV-3D People Counter. Contact your

dealer for more information.

Options Detail

Wall Mount Kit

The Wall Mount Kit is used to mount the GV-3D People

Counter to the wall.

 L-type brackets x 2

 Small screws x 4

VESA Monitor Mount Kit

The VESA Monitor Mount Kit is used to mount the GV-3D

People Counter to the back of a VESA monitor.

 VESA monitor mount bracket x 1

 L-type brackets x 2

 Large screws x 4

 Small screws x 8

Asus Xtion Pro Live

The Asus Xtion Pro Live is a motion sensor used to detect

the number of people who have walked through the

detection area. The operating temperature is from 0°C ~

40°C / 40°F ~ 104°F.

Asus Xtion Pro / Asus Xtion

Pro Live In-Ceiling Mount

The In-Ceiling Mount is used to mount Asus Xtion Pro /

Asus Xtion Pro Live on the ceiling.

 Cover for in-ceiling mount x 1

 Magnet x 2

 Support bracket x 2

 Black long screw x 2

 Screw nut x 2

USB Extension Cable

The 1.8 meters (5.9 feet) USB extension cable can extend

the distance between the Asus Xtion Pro / Asus Xtion Pro

Live and the GV-3D People Counter.

*You can connect multiple USB extension cables, but the

total distance cannot exceed 5 meters (16.4 feet).

3

4

1.5 Overview

This section identifies the components of the GV-3D People Counter.

1.5.1 Front View

1

2

3 4

5

Figure 1-2

No. Name Function

1 LED Indicators

The green LED indicates the Asus Xtion Pro / Asus Xtion Pro Live

is connected. The red LED indicates the power is supplied.

2 USB Connect to an Asus Xtion Pro / Asus Xtion Pro Live.

3 IR

Built-in IR receiver to receive the IR signals from the IR remote

control.

4 Default Reset the GV-3D People Counter to the default factory settings.

5 SD Card Slot Connect to a SD card for local storage and firmware upgrade.

Introduction

1

1.5.2 Rear View

Figure 1-3

No. Name Function

1 Ethernet Connect to an Ethernet.

2 SPDIF Reserved (not functional).

3 HDMI Connect to an HDMI supported display device.

4 VGA Connect to a VGA monitor.

5 L/R Connect to a speaker.

6 Power OFF/ON Switch the power on or off.

7 DC 12V Connect to power by using the supplied power adapter.

5

6

1.6 The IR Remote Control

Figure 1-4

No. Name Function

1 Reboot Reboot the device.

2

Number / Alphabets /

Punctuation Marks

Enter the numbers, alphabets or punctuation marks.

3 Back Exit the Setup Menu and return to the counting page.

4 Direction Arrows Move up, down, right and left in the Setup Menu.

5 Rec Save the settings in the Setup Menu.

6 Menu Switch to the setup menu.

7 OK Enter the setup options in the Setup Menu.

Introduction

7

1

Press Shift and 0~7 to switch to one of the 8 resolutions below.

Shift + 0 : VGA_640 x 480

Shift + 1 : VGA_1024 x 768

Shift + 2 : VGA_1280 x 768

Shift + 3 : VGA_1366 x 768

Shift + 4 : HDMI_480p

Shift + 5 : HDMI_720p

Shift + 6 : HDMI_1080i

Shift + 7 : HDMI_1080p

8 Shift

Note the resolution switch will cause the GV-3D People Counter

to automatically reboot.

8

Chapter 2 Getting Started

2.1 Connecting the Device

The instructions below describe the connection required to operate GV-3D People Counter.

Note:

1. For more accurate counting results, avoid placing the Asus Xtion Pro / Asus Xtion Pro Live

where it can be subjected to direct sunlight or exposed to IR LED.

2. You can only connect GV-3D People Counter to one display device through HDMI or VGA

connector. The video signal will be unstable if multiple display devices are connected.

Figure 2-1

Getting Started

2

1. Connect a display device to VGA video connector or HDMI connector for video and audio

alarm combined outputs.

2. Connect to a standard network cable.

3. If you use a VGA monitor, connect a speaker to L/R port for audio alarm.

4. Insert an SD card.

5. Connect the Asus Xtion Pro / Asus Xtion Pro Live to the USB port of the GV-3D People

Counter. The recommended installation height for Asus Xtion Pro / Asus Xtion Pro Live is

between 1.8 – 5 meters.

6. Connect to power using the supplied power adapter.

7. Switch the Power button to ON.

2.2 Restoring to Factory Default Settings

If you need to restore the GV-3D People Counter to factory default settings, follow the steps

below:

1. Press and hold the Default button on the front panel.

Figure 2-2

2. Release the Default button when the green LED stops blinking. The GV-3D People

Counter will automatically reboot after loading default.

Note: The power should always be on during the process of loading default.

9

10

2.3 Installing Wall Mount (Optional)

You can separately purchase the Wall Mount Kit to mount GV-3D People Counter on a wall.

1. Unscrew the 4 screws on the back panel of the GV-3D People Counter.

Figure 2-3

2. Use the 4 screws in the package to tighten the L-type brackets on the GV-3D People

Counter.

L-Type Bracket L-Type Bracket

Figure 2-4

Getting Started

2

2.4 Installing VESA Monitor Mount (Optional)

You can separately purchase the VESA Monitor Mount for installing GV-3D People Counter to

the back of a VESA monitor.

1. Follow steps 1 and 2 in 2.2 Installing Wall Mount to tighten the L-type brackets on the back

panel of GV-3D People Counter.

2. Using the 4 large screws, tighten the VESA monitor mount bracket on the back of the

computer monitor.

Figure 2-5

3. Use the 4 small screws to tighten the GV-3D People Counter and the VESA monitor

mount bracket together.

Figure 2-6

11

12

2.5 Installing In-Ceiling Mount (Optional)

You can separately purchase the in-ceiling mount to mount Asus Xtion Pro / Asus Xtion Pro

Live on the ceiling. Before installing, note the following recommendations for in-ceiling mount:

 The thickness of the ceiling board should be between 0.5 – 3.0 cm / 0.2 – 1.18 in.

 The recommended installation height for Asus Xtion Pro / Asus Xtion Pro Live is between

1.8 – 5 meters.

1. Cut a rectangular hole in the ceiling with the measurements of 20.5 x 4.36 cm /

8.07 x 1.72 in.

Figure 2-7

2. Remove the two round cover plates and unscrew the screw underneath the cover plate to

remove the base.

Figure 2-8

Getting Started

2

3. Unscrew the screws on two ends of the Asus Xtion Pro / Asus Xtion Pro Live.

Figure 2-9

4. Insert the 2 black screws into the screw nuts and assemble the 2 black screws with

support brackets.

Figure 2-10

5. Assemble the support brackets with Asus Xtion Pro / Asus Xtion Pro Live and tighten the

screws.

Figure 2-11

13

14

6. Insert the Asus Xtion Pro / Asus Xtion Pro Live into the hole in the ceiling board. Make

sure the black plastic clips are pointing vertically against the support brackets and can

pass through the hole.

Figure 2-12

7. After inserting, make the black plastic clips parallel with Asus Xtion Pro / Asus Xtion Pro

Live.

Figure 2-13

8. Tighten the screws to adjust the black plastic clips and make sure they can wedge the

ceiling.

Figure 2-14

Page is loading ...

Geovision GV-3D User manual

Geovision GV-3D User manual

Related papers

Other documents