Swann SWNVW-GUAEYE Quick start guide

Brand: Swann

Model: SWNVW-GUAEYE

Category: Network antennas

Type: Quick start guide

NVR Quick Start Guide

• Getting to know your NVR

• What does this mean?

• Installing the Wi-Fi Antennas

• Connect your Cameras

• Connect your NVR to your Home Network

• Connect your Mouse

• Connect your NVR to your HDTV

• Connect your Power Adapter

QHGUAEYE111215E | © Swann 2015

Welcome! Lets get started.

READ ME

FIRST!

Congratulations on the purchase of your Swann NVR. This quick start guide will assist you on getting your NVR up and

running as soon as possible. We recommend that you connect everything and give it a try before you do a permanent

installation, to make sure nothing was damaged during shipping. On the other side is a detailed connection map which

illustrates the various connections on the NVR.

Getting to know your NVR

1) Wi-Fi Input

2) LAN

3) Audio Out

4) VGA

5) HDMI

6) USB

7) Wi-Fi Input

8) Power Input

9) PWR LED

10) HDD LED

Look out for the light bulb icon,

as this provides information on

the operation of your NVR.

PWR HDD

4 Channel HD Network Video Recorder

VGA

USB

AUDIO

OUT

LAN

DC 12V IN

2 3 4 5 6 8

1 & 7) Wi-Fi Input - The supplied Wi-Fi antenna connects

here. The Wi-Fi antenna communicates with the supplied

cameras as well as your Wi-Fi network.

2) LAN - Connect this to your home network so your NVR

can connect to the Internet (required for AP mode only).

3) Audio Out - For connecting speakers.

4) VGA - If you have a digital TV or a monitor with a

VGA connection, connect this to an available input (this

connection is not required when using the HDMI cable).

5) HDMI - Connect this to your digital TV with a HDMI input

(HDMI cable supplied).

6) USB - Connect the mouse here. Also able to connect

a storage device such as a USB flash drive to back up

recorded events or to perform a firmware upgrade.

8) Power Input - Connect the DC 12V power adapter here.

9) PWR LED - Indicates the NVR has power.

10) HDD LED - Will flash when the hard drive is working.

What does this mean?

FCC Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures -

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Caution: Any changes or modifications to this device not explicitly

approved by manufacturer could void your authority to operate this

equipment. This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Step One - Installing the Wi-Fi Antennas

1. Located at the rear of your NVR are two Wi-Fi antenna

connections. There is also a single Wi-Fi connection at the

rear of each camera.

2. As there are several Wi-Fi antennas provided, use the

two longer versions for your NVR and the shorter versions

for each camera.

3. Use a clockwise motion to connect. Make sure the

antenna is connected firmly but not excessively. It is

recommended to leave the antenna in a vertical position

for best reception.

H D M I

U S B

DC 12V

1. Connect the Power Input on the camera to the Power

Output on the Power Extension Cable. Repeat this step for

each camera provided.

2. Connect the Power Input on the Power Extension Cable

to the Power Adapter. Repeat this step for each Power

Adapter provided.

3. Connect each Power Adapter to a wall socket. Press the

wall socket’s switch to the on position to supply power.

Reset - To reset your camera, press and hold the reset

button, connect power and continue holding for 10 seconds.

LAN - This can be used to configure your camera to your

Wi-Fi network.

Step Two - Connect your Cameras

LAN

Reset

Power

Input

Power

Output

Power

Input

Power Extension

Cable

Power Adapter

Connect the supplied Ethernet cable (1) to the LAN connection on the NVR then connect the other end to a spare port

on your router or wireless access point. Don’t proceed to the next step until this is done.

Please note - AP mode allows wireless communication with your cameras, however your NVR must be

connected to your router to send email alerts, synchronise its internal clock and for remote access.

Step Three - Connect your NVR to your Home Network

US B

Int er net

VGA

USB

AUDIO

OUT

LAN

DC 12V IN

Connect the supplied mouse (1) to one of the available USB ports. You can connect a USB storage device such as a

flash drive (not included) to the other port, to back up your video recordings and to perform a firmware upgrade.

Step Four - Connect your Mouse

Please note - Bluetooth and wireless mice and trackpad devices are not supported. Not all USB storage devices

are supported.

VGA

USB

AUDIO

OUT

LAN

DC 12V IN

Connect the supplied HDMI cable to the HDMI output on the NVR then connect the other end to a spare HDMI input (1)

on your HDTV. Make sure the video input on the HDTV matches the physical connection used to connect the NVR.

Step Five - Connect your NVR to your HDTV

HDMI IN 2

HDMI IN 1

VGA

USB

AUDIO

OUT

LAN

DC 12V IN

Connect the supplied power adapter’s power connection (1) to the power input on your NVR first (this will minimise

sparking) then connect the power adapter to a spare wall socket (illustration may differ from what is supplied).

All the connections have now been completed. You’re now ready to run through “The Wizard” quick start guide (the red

coloured one) to configure your NVR.

Step Six - Connect your Power Adapter

VGA

USB

AUDIO

OUT

LAN

DC 12V IN

Swann SWNVW-GUAEYE Quick start guide

Brand: Swann

Model: SWNVW-GUAEYE

Category: Network antennas

Type: Quick start guide

Download PDF

report

Swann SWNVW-GUAEYE Quick start guide

Swann SWNVW-GUAEYE Quick start guide

Related papers

Other documents