Enclume DR23 HS Installation guide

Brand: Enclume

Model: DR23 HS

Type: Installation guide

Enclume DR23 HS is the ultimate quality, design, strength, and function. It is a compact scroll rack that can be used to store and organize various items, especially pots and pans. The rack comes with all the necessary hardware for assembly and installation, including two ceiling hooks, two 2-inch "S" hooks, two 6-inch décor chains, eight 1/4" x 3/8" button head screws, two barrel screws, two barrel nuts, two 5/32" hex key wrenches, and a Toggler kit.

The rack is made up of four arms, one oval body, two lower side bars, and one upper hanging bar.

  



DR 23-Décor Compact Scroll Rack

 

nclosed you will find everything needed for

the assembly and use of your pot rack. Two

people make assembly and installation much

easier. The parts and hardware included are:

Hardware included:

2 – Ceiling Hooks - large

2 – 2-inch “S” Hook

2 – 6” Décor Chain

8 – 1/4” x 3/8” Button Head Screws

2 – Barrel Screws, #10 x 24 x 7/16”

2 – Barrel Nuts, #10 x 24 x 5/16

2 – 5 /32" Hex Key Wrenches

Toggler Kit

See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS

Components included:

4 – Arms

1 – Oval Body

2 – Lower Side Bars

1 – Upper Hanging Bar

6 – Pot hooks - EPHS

6 – Pot hooks - DRPHS

Thank you for choosing Enclume!

Enclume racks are the ultimate quality,

design, strength and function.

WARNING: READ ALL OF THE

INSTRUCTIONS BEFORE

ASSEMBLING AND USING YOUR

RACK

If you need help, please call 1-877-ENCLUME

Enclume Design Products

24 Colwell Street, Port Hadlock, WA 98339

Phone 360-385-6100  Fax 360-385-6156

www.enclume.com

ASSEMBLY INSTRUCTIONS

1) Place the rack components on a firm, flat surface. You can protect the surface with the corrugated shipping box.

2) Identify the four arms and determine the lower end of each arm – this is the section on the arm where a screw hole is

made on a flat area.

3) Identify the oval rack body. Using four of the ¼” x 3/8” button head screws and the hex key wrench, loosely attach

the lower ends of the four arms, one at a time, to the outside of the oval body as shown in the diagram above.

4) Now locate the upper hang bar (this is the bar with two large and two small holes in it) and the set of two barrel

screws and two barrel nuts. Place the upper hang bar between the tops of the arms (which form two arm pairs) and

insert one barrel nut: 1) through the top hole in one arm, 2) then through the upper hang bar, and finally 3) through the

hole in the other arm of the pair. Holding this assembly in place, insert the barrel screw into the barrel nut and loosely

attach with the hex key wrench.

6) Repeat the process set out in step 4) to attach the other arm pair to the upper hang bar using the remaining barrel nut

and barrel screw.

7) Next locate the two lower side bars. One side of the rack at a time, attach a lower side bar to the inside front of the

lower scrolls of the two arms on one rack side. Attach with two of the ¼ x 3/8 button head screws, inserting the screws

through the outside of the arm scroll and driving them into the lower side bar with the hex key wrench

8) Place your assembled rack on a level surface and square it up. The arms need to be at right angles to the hang bar and

the side bars. Then with a hex key wrench firmly tighten the lower part of the arms to the oval body and tighten the

the arm scrolls onto the lower side bars. Finally, using hex key wrenches on both sides of the barrel bolt, firmly tighten

each arm pair around the upper hang bar.

INSTALLATION and USE INSTRUCTIONS

1) We recommend that you anchor your rack into the solid wood of ceiling joists or beams. Carefully measure the area

where the rack is to be hung and install the ceiling screw hooks directly into the wood joists. If it is not convenient to

hang your rack directly into wood joists you may use the included DRYWALL anchors enclosed with your rack. See

Toggler® brand manufacturer recommendations for weight limits included in the instructions in the Toggler kit.

3) Insert one end of one chain into one of the ceiling screw hooks. Place one end of one "S" hook into the other end of

the chain. Repeat this for the chain and “S” hook at the other end of the rack.

4) Carefully lift your rack into place and attach the two top holes in the upper hang bar to the two “S” hooks at the

lower end of the two chains.

7) Note: Use of the hanging chains is optional; you may choose to not use it and thus raise your rack another six inches.

8) Please take care to distribute and balance heavier items around the rack.

It is important that your rack is assembled correctly. If assembled or used

incorrectly, it could become unstable and collapse, possibly causing injury.

WARNING

Limited Warranty: This product is warranted to be free of defects in material or workmanship for a period of five years from the date of your

purchase. Your exclusive remedy shall be the repair or replacement of the defective product, and shall be subject to the following conditions: (1) you

provide notice of any defect to Enclume within the warranty period, and (2) you return the defective product to Enclume Design Products, (24 Colwell

St., Port Hadlock, WA 98339), postage prepaid within 20 days of obtaining a return authorization number from Enclume (which may be obtained by

telephoning the number at the top of this instructions). There are no other warranties, expressed or implied, applicable to this product. FURTHER,

THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ENCLUME

SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE PURCHASE

OR USE OF THIS PRODUCT.

Enclume DR23 HS Installation guide

Brand: Enclume

Model: DR23 HS

Type: Installation guide

The rack is made up of four arms, one oval body, two lower side bars, and one upper hanging bar.

Download PDF

report

Enclume DR23 HS Installation guide

Enclume DR23 HS Installation guide

Related papers

Other documents