CAMONS Digital Wireless Backup Camera for RV, 9” Monitor Quad Split No Flicker, Built-in DVR, 120°HD Night Vision IP69 Waterproof Camera Rear/Side/Front User manual

Brand
CAMONS
Model
Digital Wireless Backup Camera for RV, 9” Monitor Quad Split No Flicker, Built-in DVR, 120°HD Night Vision IP69 Waterproof Camera Rear/Side/Front
Type
User manual
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N M
N M
A
A
N
N
U
U
A
A
L
L
CAUTION:Please pair the cameras before installation
if you purchased extra wireless cameras!
Normally you do not need to pair the camera and monitor,what you need
to do are as follows:
1.Find out the installation place of the camera and the power of reversing light(or ACC).
2.Install the monitor to a suitable place and connect it to the cigarette lighter.
Customer Support:
Email:[email protected]
Phone: 86-013798241290
Facebook Messenger:Camons.fans
How to pair?
B.Suction cup mounting
☆ Install the monitor at the proper position.
☆ Plugging the cigarette lighter into the car cigarette socket.
☆ The display is 4 split display with four trigger wires, and the trigger wires were labeled with
1, 2, 3, 4.
The trigger wire 1/2/3/4 corresponds to CAM1/CAM2/CAM3/CAM4.
Connecting the monitor and camera with DC12V-24V power supply. The camera was paired default in
CAM1 Channel. If you want to switch to CAM2, first press the “CAM ”button on the display, choose
CAM2 channel, Press “M” button to select "PAIRING", then press “REC” to enter the "paring mode".
Short pressing the camera's paring key to start. After the pairing successed, the camera image will
be displayed
and the pairing are finished.
Monitor Installation:
A.Bracket mounting
Wire connection:
DC12-24V
CAM1 Trigger wire
CAM2 Trigger wire
CAM3 Trigger wire
CAM4 Trigger wire
Cigarette lighter
7
Trigger1
Trigger2
Trigger3
Trigger4
1.Green wire
2.Blue wire
3.Brown wire
4.Gray wire
CAM2 CAM3 CAM4
CAM1
①
②
③
④
Camera installation:
1. Drill the hole in the proper position of the vehicle.
2. After fixing the bracket, lead the camera wire through the cable hole and seal the hole with
grommet and sealant.
3. Lock the camera at suitable angle with the bracket by using screws, connecting the power
supply to reversing light's power or ACC power.
Installation Diagram
Cable hole
Pairing Button
DC12-24V
DC12V-24V (reversing light’s 12V), GND
Backup Camera
Trigger function descriptions:
Adjust the camera’s angle
(2 screws)
Unscrew the outter housing
(3 screws)
Drill holes to mount the
camera’s base at suitable
place (4 screws)
Side Camera( )Left Side Camera( )Right
1. Connecting the backup camera with the power supply of the reversing light (or ACC).
2. Connecting the side-mounted camera to a suitable power source.
Wireless side camera
DC12-24V (RED)
Antenna
GND (BLACK)
Rear Camera
Pairing Button
Wireless L
icense
Plate Camera
Horizontal 115°
DC12-24V (RED)
Antenna
GND (BLACK)
Pairing Button
+ +
+ +
+
+
STAND BRACKET INSTALLATION
3M GLUE BRACKET INSTALLATION
or
or
Install above the license plate
Install under the license plate
Install above the license plate
Install under the license plate
+ +
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

CAMONS Digital Wireless Backup Camera for RV, 9” Monitor Quad Split No Flicker, Built-in DVR, 120°HD Night Vision IP69 Waterproof Camera Rear/Side/Front User manual

Brand
CAMONS
Model
Digital Wireless Backup Camera for RV, 9” Monitor Quad Split No Flicker, Built-in DVR, 120°HD Night Vision IP69 Waterproof Camera Rear/Side/Front
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents