Axis T8604 Owner's manual

INSTALLATION GUIDE

ENGLISH DEUTSCH

ITALIANO

ESPAÑOL

FRAN

Ç

AIS

AXIS T8604 Media Converter Switch

Legal Considerations

Video and audio surveillance can be prohibited

by laws that vary from country to country. Check

the laws in your local region before using this

product for surveillance purposes.

Electromagnetic Compatibility (EMC)

This equipment has been designed and tested to

fulfill applicable standards for:

• Radio frequency emission when installed

according to the instructions and used in its

intended environment.

• Immunity to electrical and electromagnetic

phenomena when installed according to the

instructions and used in its intended

environment.

USA - This equipment has been tested using a

shielded network cable and found to comply

with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference when

the equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications. Operation

of this equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the interference

at his own expense.

Canada - This Class A digital apparatus

complies with Canadian ICES-003.

Europe - This digital equipment

fulfills the requirements for RF emission

according to the Class A limit of

EN 55022. NOTICE! This is a Class A product. In a

domestic environment this product may cause

RF interference, in which case the user may be

required to take adequate measures. This

product fulfills the requirements for emissions

and immunity according to EN 50121-4 and

IEC 62236-4 railway applications. This product

fulfills the requirements for immunity according

to EN 61000-6-1 residential, commercial and

light-industrial environments. This product

fulfills the requirements for immunity according

to EN 61000-6-2 industrial environments. This

product fulfills the requirements for immunity

according to EN 55024 office and commercial

environments.

Australia - This digital equipment fulfills the

requirements for RF emission according to the

Class A limit of AS/NZS CISPR 22.

Safety - This product complies with

IEC/EN 60950-1 Safety of Information

Technology Equipment.

Equipment Modifications - This

equipment must be installed and used in strict

accordance with the instructions given in the

user documentation. This equipment contains no

user-serviceable components. Unauthorized

equipment changes or modifications will

invalidate all applicable regulatory certifications

and approvals.

Liability - Every care has been taken in the

preparation of this document. Please inform

your local Axis office of any inaccuracies or

omissions. Axis Communications AB cannot be

held responsible for any technical or

typographical errors and reserves the right to

make changes to the product and

documentation without prior notice. Axis

Communications AB makes no warranty of any

kind with regard to the material contained

within this document, including, but not limited

to, the implied warranties of merchantability

and fitness for a particular purpose. Axis

Communications AB shall not be liable nor

responsible for incidental or consequential

damages in connection with the furnishing,

performance or use of this material. This product

is only to be used for its intended purpose.

RoHS - This product complies with

both the European RoHS directive,

2002/95/EC, and the Chinese RoHS

regulations, ACPEIP.

WEEE Directive

The European Union has enacted a

Directive 2002/96/EC on Waste

Electrical and Electronic Equipment

(WEEE Directive). This directive is

applicable in the European Union member

states.

The WEEE marking on this product (see right) or

its documentation indicates that the product

must not be disposed of together with

household waste. To prevent possible harm to

human health and/or the environment, the

Korea - ࢇ̛̛Е߶הࡈ$̗ࢷ࢕ળࢶଢ̛̛Ի۰

શ֐࢕ӖЕیࡈ࢕Еࢇࢺࡶ࣯ࢂଜݤ̛؂Ԃֲ

ɼࢽ࠹ࢂएࠇ߾۰یࡈଜЕʨࡶּࢶࡳԻଢТЬ



Japan -

product must be disposed of in an approved and

environmentally safe recycling process. For

further information on how to dispose of this

product correctly, contact the product supplier,

or the local authority responsible for waste

disposal in your area.

Business users should contact the product

supplier for information on how to dispose of

this product correctly. This product should not

be mixed with other commercial waste.

Support - Should you require any technical

assistance, please contact your Axis reseller. If

your questions cannot be answered immediately,

your reseller will forward your queries through

the appropriate channels to ensure a rapid

response. If you are connected to the Internet,

you can:

• download user documentation and software

updates

• find answers to resolved problems in the FAQ

database. Search by product, category, or

phrase

• report problems to Axis support staff by

logging in to your private support area

• chat with Axis support staff (selected

countries only)

• visit Axis Support at www.axis.com/techsup/

Page is loading ...

Safeguards

Please read through this Installation Guide carefully before installing the Axis

product. Keep the Installation Guide for further reference.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure. Do not

install the product on unstable brackets, unstable or vibrating surfaces or

walls, since this could cause damage to the product.

• Only use applicable tools when installing the Axis product; excessive force

could cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth

for cleaning.

• Use only accessories that comply with technical specification of the product.

These can be provided by Axis or a third party.

• Use only spare parts provided by or recommended by Axis.

• Do not attempt to repair the product by yourself, contact Axis or your Axis

reseller for service matters.

• This Axis product shall be used in compliance with local laws and regulations.

• To use this Axis product outdoors, it shall be installed in an approved outdoor

housing.

• The Axis product should be installed by a trained professional. Observe rele-

vant national and local regulations for the installation.

Transportation

• When transporting the Axis product, use the original packaging or equivalent

to prevent damage to the product.

ENGLISH

Page is loading ...

AXIS T8604 Page 7

ENGLISH

AXIS T8604 Installation Guide

This Installation Guide provides instructions for installing AXIS T8604 Media

Converter Switch on your network.

Installation Steps

1. Check the package contents against the list below.

2. Hardware overview. See page 8.

3. Install the hardware. See page 10.

Package Contents

Item Models/variants/notes

Media converter switch AXIS T8604

Mounting kit Clip for DIN clip

Screw (2x)

Printed materials AXIS T8604 Installation Guide (this document)

Optional accessories SFP module

Page 8 AXIS T8604

Hardware Overview

Each RJ-45 and SFP connector has its own dip switch, which is accessed by

removing the cover. However, removing the cover is not necessary because the dip

switches shall be left in their original positions (position B) unless connecting one

or more ports to AXIS Q6032-C/Q6034-C/Q6035-C and AXIS T8605. For more

information, see AXIS Q6032-C/Q6034-C/Q6035-C User Manuals.

Network connector RJ-45

Network connector

Cover

Power LED

Network LED indicator (4x)

ETH 1/2/3/4

indicator

(2x)

Power connector

(DC input)

Ground screw

SFP

AXIS T8604 Page 9

ENGLISH

Connectors

Network connector RJ-45 (external) - Two RJ-45 connectors (10Base-T/

100Base-TX) for network connectivity.

Network connector SFP (external) - Two SFP connectors (100Base-FX/1000Base-

X) for network connectivity.

LED Indicators

Power connector (DC input) - 2-pin terminal block for power input.

Function Pin Notes Specifications

DC input GND 1 Ground

12 V DC 2 Power in from

power supply (sold

separately)

Max load = 0.3 A

12 - 13.2VDC, min3.5W

LED Color Indication

Power Unlit DC power unconnected or current protection

engaged (power overload).

Green DC power connected.

Network (4x) Amber 10 Mbit connection. Flashes during activity.

Green 100/1000 Mbit connection. Flashes during activity.

-+

21

Page 10 AXIS T8604

Install the Hardware

• The media converter switch shall be installed in an environment pro-

tected against dust and water, for example indoors or in an appropriate

cabinet.

• The media converter switch shall be connected using shielded network

cables (STP) intended for their specific use. Make sure that the switch is

properly grounded. See Electromagnetic Compatibility (EMC) for regula-

tory requirements.

1. Mount the media converter switch on the wall or, if applicable, attach it to a

DIN rail in the cabinet.

2. Connect the network cables to the network connectors (RJ-45, SFP) as

required.

Network connector

SFP (2x)

RJ-45 (2x)

Ground screw

Power connector

(DC input)

AXIS T8604 Page 11

ENGLISH

3. Connect the power cable to the power connector (DC input).

4. Earth the switch by connecting to the ground screw.

5. Make sure the LED indicators on the media converter switch indicate the

correct conditions. For information, see LED Indicators, on page 9.

Power LED

Network LED (4x)

ETH 1/2/3/4

Page 12 AXIS T8604

Technical specifications

Function/group Item Specifications

Media converter

switch

Model AXIS T8604

General Casing Metal

Power 12–13.2 V DC, max 3.5 W

Connectors 2x RJ-45 connectors (10/100 Mbps)*

2x SFP connectors (100/1000 Mbps)

for SFP fiber optic modules or SFP to

copper modules

1x power

*use shielded cables (STP) CAT5 or

higher

Environment Indoor/cabinet

Operating conditions -40 °C to 75 °C (-40 °F to 167 °F)

Approvals EN 55022 Class A, EN 61000-3-2,

EN 61000-3-3, EN 61000-6-1,

EN 61000-6-2, EN 55024

FCC Part 15 Subpart B Class A

ICES-003 Class A

C-tick AS/NZS CISPR 22

KCC Class A

VCCI Class A

IEC/EN 60950-1

Weight 284 g (0.63 lb.)

Dimensions

(HxWxD)

150 x 100 x 30 mm (5.9” x 3.9” x 1.2”)

Included Accessories Installation Guide, clip for DIN rail

Optional Accessories SFP module

AXIS T8604 Page 13

ENGLISH

Further Information

Visit Axis learning center www.axis.com/academy for useful trainings, webinars,

tutorials and guides

.

Warranty

For information about Axis’ product warranty and thereto related information, see

www.axis.com/warranty

Page is loading ...

Página 52 AXIS T8604

Especificaciones técnicas

Función/Grupo Artículo Especificaciones

Switch

convertidor de

medios

Modelo AXIS T8604

Generales Carcasa Metálica

Alimentación 12-13,2 V CC, máx. 3,5 W

Conectores 2 conectores RJ-45 (10/100 Mbps)*

2 conectores SFP (100/1000 Mbps)

para los módulos SFP de fibra óptica o

SFP para módulos de cobre

1 alimentación

*use cables blindados (STP) CAT5 o

superior

Entorno Interior/armario

Condiciones de

funcionamiento

-40 °C a 75 °C (-40 °F a 167 °F)

Homologaciones EN 55022 Clase A, EN 61000-3-2,

EN 61000-3-3, EN 61000-6-1,

EN 61000-6-2, EN 55024

FCC Parte 15 Subparte B Clase A

ICES-003 Clase A

C-tick AS/NZS CISPR 22

KCC Clase A

VCCI Clase A

IEC/EN 60950-1

Peso 284g (0,63lb)

Dimensiones

(Alt. x Anch. x Prof.)

150 x 100 x 30 mm (5,9” x 3,9” x 1,2”)

Accesorios incluidos Guía de instalación, clip para el riel

DIN

Accesorios

opcionales

Módulo SFP

Page is loading ...

Installation Guide Ver.1.1

AXIS T8604 Printed: October 2012

Axis T8604 Owner's manual

Axis T8604 Owner's manual

in other languages

Related papers

Other documents