KADO
LUX BACK TO WALL PAN
SPECIFICATIONS
Recommended Use Domestic, Hotel and Commercial
Material Vitreous china
Colour White
Weight Pan: 28kg
Seat Soft close quick release toilet seat
Soft close quick release thin toilet seat
Rim Configuration Box Rim
Bowl Configuration Universal S & P
Set Out S Trap: 95-105mm
Pan Fixing Screwed to floor (Fixing Screws supplied)
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved bathroom cleaners.
This bathroom product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions .
To see the complete KADO range go to
www.reece.com.au/bathrooms
Dimensions are nominal measurements only
100
180
360
545
245
95-105
370 320
180
30
65
TM
WMKA21192
AS 1172.1
Licence No.0025
A joint government and industry
program
The more
stars the more
water efficient
litres per full flush
litres per average flush
when tested in accordance with standard AS/NZS6400
For more information and to compare
products refer to:
3 litres per half flush
4.5
3.5
page 1 of 4
Disclaimer: Products in this specification manual must by regulation be installed by licensed and
registered trade people. The manufacturer/distributor reserves the right to vary specifications or
delete models from their range without prior notification. Dimensions are nominal measurements only.
Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor
takes no responsibility for printing errors.
Tech Page Version 3
KADO
LUX BACK TO WALL PAN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
INSTALLATION INSTRUCTIONS
A
100mm
180mm
Position pan against wall and mark off pan fixing holes on floor. Water inlet pipe should be roughed in at 320mm. Cut inlet pipe
so that 100mm protrudes from finished wall and attach seal.
320mm
Fixing bracket & Water inlet
Insert waste pipe
into floor at a setout of 95-105
and180mm
above
finished floor and fix bracket into position as per diagram above.
Push pan into position. Ensure that you make a firm connection with inlet and
outlet pipes and avoid disturbing the floor fixing brackets. Flush test for leaks.
180mm
180mm
S-Trap Installation
NOTE: This is a set out of 95-105mm
100mm DWV with pan collar (not supplied). Push pan back into position. Ensure that you make a firm connection with inlet and outlet pipes
and avoid disturbing the floor fixing brackets. Flush test for leaks.
180mm
P-Trap Installation
Ensure that pan is level. Fix pan to floor using fixing screws and flexible sealant. Install soft closing seat.
sealant
Fixing Pan to Floor
95-105
page 2 of 4
KADO
LUX BACK TO WALL PAN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
LUX THIN SEAT INSTALLATION INSTRUCTIONS
A
Warning：
Using an abrasive cleaner (such as a toilet bowl cleaner) on the seat, seat cover, hinges or hinge covers can cause damage.
If any of these components come into contact with such a cleaner, use a damp rag or sponge to wipe off immediately.
CLICK
CLICK
1
2
3
1 2 3
B
1
2
0
0
1mm
≈
A
1
2
360˚
3.1
3.1 3.2
3.2
Cleaning
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
INSTALLATION INSTRUCTIONS
C
D
F
E
B (x2)
C (x2)
D (x2)
F (x2)
E (x2)
Important Note:
Soft close seat and covers can take up to 30 seconds to close. Do not force the closing
mechanism as this may result in damage. The fixings of your seat may require re-tightening
occasionally depending on use.
Installation
Warning：
1 2 3
1
2
3.1
3.1 3.2
3.2
Cleaning
Picture Reece Code Product Description Part Number
9506341 KADO LUX THIN SEAT BUFFER SET I9037-RPC1
9506342 KADO LUX THIN SEAT HINGE SET I9038-RPC1
SPARE PARTS
page 3 of 4
KADO
LUX BACK TO WALL PAN
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
LUX SEAT INSTALLATION INSTRUCTIONS
Top Fixing Installation procedure.
1. Insert the nylon toggles into the hinge holes of the pan.
2. Mount the hinges onto the shaft of the toilet seat.
3. Plug the bolt into the nylon toggle.
4. Align the toilet seat with the pan.
5. Tighten the screws.
6. Push the button to release the seat.
7. Lift the toilet seat.
8. Insert hinge covers over posts.
9. Fix seat into final position.
Important Note:
Soft close seat and covers can take up to 30 seconds to close. Do not force the closing
mechanism as this may result in damage. The fixings of your seat may require re-tightening
occasionally depending on use.
page 4 of 4
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Duravit D46002 Specification Manual
-
-
DURA 1103485 Installation guide
-
Croydex WL601931H User manual
-
Croydex WL610722H User manual
-
Better Bathrooms BeBa_17297 User manual
-
Laufen 9504540 Technical Guide
-
Crosswater US-SEATU8 Installation guide
-
-
Anvil COA2020 User manual
