CAME HEI, DALI-32, DDMX-512 Installation guide

Brand: CAME

Model: HEI, DALI-32, DDMX-512

Type: Installation guide

001DDALI-32

O N D I P

1 2 34

00 1D DA L I- 32

B US DAL I

S+

24 V dc

D+ D-

1 2 48

O F F

001DDMX512

R S 485

D+

S+

24 V dc

001DDMX 512

1 2 48

O F F

Domoticline

001DDALI-32 For lights with a dimmer switch

001DDMX-512 For RGB lights

INSTALLATION MANUAL

Light source

control module

English - Manual code: 119 R V 57 vers. 2.2 10/2012 © CAME cancelli automatici S.p.A.

The data and information provided in this manual are subject to change at any time without any obligation

to provide prior notice on the part of CAME Cancelli Automatici S.p.A.

DETAILS

PROGRAMMING PARAMETERS

DALI CONTROL MODULE DMX CONTROL MODULE

The protocol interface modules serve to connect the HeiBus with the other systems

already available on the market. This allows users to expand the system to include

other protocols, which makes the HeiBus protocol much more ﬂexible.

TECHNICAL DATA MIN MAX

Power supply 22 V DC 24 V DC

Power drawn (at 24 V DC) 35 mA 350 mA

Maximum number of DALI lights 32

Operating temperature -5°C +40°C

Storage temperature -10°C +50°C

Relative humidity during operation 93% R.H. without condensation

Relative humidity during storage 85% R.H. without condensation

Weight 110 g

Container material White ABS

Dimensions (WxHxD) 3 DIN modules/ 52x90x60 mm

Polarity inversion protection yes

Bus protection fuse 50 mA auto-reset

TECHNICAL DATA MIN MAX

Power supply 22 V DC 24 V DC

Power drawn (at 24 V DC) 45 mA 50 mA

Maximum number of DMX channels 16

Operating temperature -5°C +40°C

Storage temperature -10°C +50°C

Relative humidity during operation 93% R.H. without condensation

Relative humidity during storage 85% R.H. without condensation

Weight 75 g

Container material White ABS

Dimensions (WxHxD) 2 DIN modules/ 35x90x60 mm

Polarity inversion protection yes

Bus protection fuse 50 mA auto-reset

The following parameters are found on devices which are deﬁned on programmes

for touch screens and on the conﬁguration programme of the Sw-heiBus version

2.08 modules

• PROGRAMMING DALI LIGHTS

• ID Module address.

• Addressing Allows the user to choose the type of connection used.

√BROADCAST Manage all lights connected to the module regardless of where

they are addressed

√SINGLE LIGHT Manage a DALI light through its address (0-63)

√SINGLE GROUPS Manage a group of DALI lights (1-15)

• LIGHT ADDRESSES Address or group of lights programmed by the DALI devices

(to be programmed using a special programmer).

• PROGRAMMING DMX LIGHTS

• ID Module address.

• ADDRESSING Allows the user to choose the type of connection used.

√CHANNELS Set the parameters for all of the managed RGB channels

√RGB LIGHT Manage a RGB light using its 3 DMX channels

• LIGHT ADDRESSES The number of the DMX channel

The module is able to command 32 DALI channels to control the light intensity

through 2 DALI bus wires (1 DALI channel = 1 light with a DALI electronic dimmer

reactor). The module directly powers the DALI bus and does not require installation

of a power supply.

PROGRAMMING: the DALI interface, for purposes of

compatibility with the mono-chrome TS commands,

features a 4-way Dip-switch for addressing the

board; see table 1.

The DALI interface can be programmed with the SW-

heiBus from the 2.0.8 version

It is able to command the ﬁrst 16 DMX channels (1 DMX=1 DMX device function),

which is ideal to control RGB lights.

PROGRAMMING: The DMX interface can be programmed

with the SW-heiBus from the 2.0.8 version

+24Vdc

SBUS

GND

Esempio di Reattore DALI

CAVO BUS

001DC3X10NG4

Esempio di Reattore DALI

N L

230Vac

O N D I P

1 2 34

00 1DD A L I -32

B US DA LI

S+

24 V dc

D+ D-

1 2 48

OF F

+24Vdc

SBUS

GND

DMX512 DECODER

CAVO BUS

009DC3X10NG4

LED RGB

ROSSO

VERDE

BLU

COM

DMX512

OUT

DMX512 DECODER LED RGB

ROSSO

VERDE

BLU

COM

DMX512

OUT

001DDMX512

D-

D+

CAVO TWIST ATO E SCHERMA TO

3 PIN XLR (PLUG)

PIN 1 : - (GND)

PIN2 : D- (DATA -)

PIN3 : D+ (DATA+)

ALIMENTAZIONE

R S 48 5

D+

S+

24 V dc

001DDMX 512

1 2 48

OF F

+24Vdc

SBUS

GND

N L

230Vac

O N D I P

1 2 34

001 DD A L I- 32

B US DA LI

S+

24 Vdc

D+ D -

1 2 48

OF F

English - Manual code: 119 R V 57 version 2.2 10/2012

DALI CONNECTION DMX CONNECTION

BUS cable

009DC3X10N G4

BUS cable

009DC3X10N G4

Twisted and shielded cable

Example of a DALI reactor

DMX-512 Decoder

Power supply

red

green

blue

com

red

green

blue

com

Power supply

Example of a DALI reactor

WARNING: the DALI interface is not a DALI

programmer. To program the DALI reactors

it is necessary to have a special program-

mer. Please contact the supplier who

provided the reactors.

ASSIGNING GROUPS TO DALI LIGHTS

DALI reactor to be programmed

DALI reactor NOT to be programmed

All the reactors which do not need to

have their programming changed must

be disconnected from the DALI network.

DALI USB Programmer

Step 1:

software installation

Install the DALI master CONFIGURATOR software and then connect

the USB cable.

The software is provided separately and can be found on the CD

together with the module conﬁguration program.

Step 2:

connection

English - Manual code: 119 R V 57 version 2.2 10/2012

ASSIGNING GROUPS TO DALI LIGHTS

Step 3:

software start up

Check that the USB interface is found.

Step 4:

assigning groups

WARNING: all the DALI lights connected to the DALI bus will be set to the

group that is being sent.

Select Broadcast.

then

ADD TO GROUP 0 (for group 1)

ADD TO GROUP 1 (for group 2)

...

And press SEND COMMAND

To remove a group, select REMOVE FROM GROUP xx

Step 5:

verify group

Select Group and the group to command

then

DIRECT ARC POWER

then

Select 100% (or another value to change the light level)

And press SEND COMMAND

English - Manual code: 119 R V 57 version 2.2 10/2012

FAILURES AND ANOMALIES

WARNING: Respect the polarity of the connection.

For the bus connection, the 009DC3X10NG4 cable is recommended (GR4, FR0R 300/500V type, 3x1mm² section).

We recommend that a shielded cable with two pairs, one twisted (D+ and D-) be used to connect the DMX module and DMX devices.

PROBLEM ANALYSIS SOLUTION

The module does not carry out any commands.

Blue LED always on

The bus terminal is connected to GND. Check the connections

of all the terminals with the bus. A module on the bus is not

powered (the 24V terminal is disconnected).

I can communicate with the bus (modules with blue LEDs switch

on), but the blue LED is always o.

The module has no power or is not connected to the rest of the

bus.

Check the connections of all the terminals with the bus.

I can communicate with the bus (modules with blue LEDs switch

on) and the blue LED ﬂashes like the other modules.

Check the board address against that set for the project on the

touch screen.

The module functions, but the lights do not switch on properly.

I switch on light 1 but light 2 activates, the intensity level is

correct.

Check touch screen programming, and reprogram the touch

screen properly.

When I switch on one light others switch on as well.

Dali – the lights are programmed with the same address or

group, reprogram the DALI lights

DMX – the lights are programmed with the same channel,

reprogram the lights

The colours are incorrect.

Dali- check that the wiring of the lights corresponds with the

Touch Screen programming for the address of the 3 colours

DMX- Check that the wiring of the DMX corresponds with the

Touch Screen programming for the 3-colour channels

TABLE 1: ADDRESSING MODULES

The interface address is the ID address for the he¡BUS modules.

Within the bus, all of the interfaces must have individual non-duplicate addresses.

The interface address can be changed at any time without needing to switch o the interface.

For DALI/DMX modules, the heiBus ID address (1-254) is used for commands from the keypad or colour TSs. For commands from monochrome TSs, set the address (0-15) in the

advanced properties of the DALI/DMX module on the SWHEIBus. The dip switches from version 2.09 are no longer managed.

CAME HEI, DALI-32, DDMX-512 Installation guide

CAME HEI, DALI-32, DDMX-512 Installation guide

CAME HEI, DALI-32, DDMX-512 Installation guide

Related papers

Other documents