Alecto PAS-300
Below you will find brief product information for Alecto PAS-300. It's an active sound set that consists of a subwoofer, two satellite speakers, and a set of speaker cables with Speakon plugs. The subwoofer has three separate speakers: one for the subwoofer and two (left and right) for the satellite speakers. The satellite speakers can be placed onto the supplied tripods. The subwoofer has volume controls for each speaker, which must be set before use. The ultimate volume is controlled on the external audio source.
Possible use cases:
- Home theater system
- PA system for small events
Alecto PAS-300
Below you will find brief product information for Alecto PAS-300. It's an active sound set that consists of a subwoofer, two satellite speakers, and a set of speaker cables with Speakon plugs. The subwoofer has three separate speakers: one for the subwoofer and two (left and right) for the satellite speakers. The satellite speakers can be placed onto the supplied tripods. The subwoofer has volume controls for each speaker, which must be set before use. The ultimate volume is controlled on the external audio source.
Possible use cases:
- Home theater system
- PA system for small events
1
USER’S MANUAL
Active sound set
PAS-300
SUB-1000
PAS-300PAS-350
2
PAS-300
RIGHT
LEFT
SUB250Watt
SAT2x75Watt
SAT OUT
LINK OUT
INPUT
PEAK PEAK PEAK
SUBLEVEL
LEFT
RIGHT
~100-240V T2.5A
PAIRSTATUS
INPUT
1+ = positive
1- = negative
2+ = no connection
2- = no connection
4Ω
75Watt rms
SATELITE PAS-300
1
9
10
11
12
Tripod
PAS-300
Subwoofer
Control Panel
GB
2
3
4
5
6
7
8
13
Satellete
Connection Panel
3
APPLICATION
The PAS-300 is a sound system with 1 subwoofer and 2 satellite speakers.
The PAS-300 is powered through a mixing panel or master output from another
amplier or audio source. The subwoofer contains three separate speakers. 1 for
the subwoofer and 2 (left and right) for the satellite speakers. The satellite speakers
may be placed onto the supplied tripods. The satellite speakers are connected
to the subwoofer using the speaker cable with Speakon plugs. The subwoofer is
provided with a volume control for each speaker. These must be set before use. The
ultimate volume is controlled on the external audio source.
FUNCTIONS
SUBWOOFER
1. Bluetooth
®
function (optional).
2. Volume controls. 2 x for satellite speakers and 1 x for subwoofer.
3. Audio input, left and right (symmetrical), XLR or jack 6.3mm.
4. Audio input, left and right (asymmetrical), Cinch.
5. Audio output, left and right (asymmetrical), XLR (the same signal as input).
6. Satellite speaker output, left and right, Speakon (cables included).
7. 230V mains lead input (included) with fuse holder T2,5A.
8. Power switch.
TRIPOD
9. height tube
10. Retainer
11. height tube lock nut
12. tripod feet lock nut
SATELLITE SPEAKER
13. Speakon speaker input (connect with speaker output (6)).
4
WARNING/MAINTENANCE
GENERAL:
• Carefully read the user’s manual and follow all directions.
• Before cleaning the speaker, always remove the mains cable from the wall
socket and switch off the speaker.
• Clean the cabinet with a slightly moist cloth.
• Never place or use the set in wet or humid space or environment.
• Ensure adequate heat dissipation; never cover the set nor place it directly next
to a heat source.
• Prevent damaging the mains cable and ensure it doesn’t cause a risk of tripping
or falling.
• Never disassemble the set; this may only be performed by qualied personnel.
• Only turn on the speaker after setting all volume controls to MINIMUM (0), to
avoid possible scares when switching on.
• Prolonged listening to high volume levels can cause hearing damage
BEFORE USE
The PAS-300 functions on the mains.
The PAS-300 satellites function on the built-in speakers in the subwoofer and
must be connected using the supplied speaker cables with Speakon plugs.
MAINS VOLTAGE:
Only connect the PAS-300 subwoofer to a mains voltage of 230 Volt. The mains in
most European countries works on 230 Volt.
Use the supplied power cord to connect the PAS-300 with the mains.
AMPLIFIER SETTINGS
POWER SWITCH:
Use the power switch to switch on the amplier.
INPUT:
Connect an external audio source to the input of the PAS-300.
The connection can be made with XLR, Jack 6.3mm of cinch plugs.
LEFT/RIGHT VOLUME CONTROL (SATELLITE):
Use the LEFT and RIGHT volume controls to adjust the volume of the satellites.
When the volume reaches the maximum level, the related peak LED will illuminate.
5
SUB LEVEL VOLUME CONTROL:
Use the SUB LEVEL volume control to adjust the volume of the subwoofer (low
pitch). When the volume reaches the maximum level, the related peak LED will
illuminate.
ADJUSTING:
Use the volume buttons to set the correct volume balance between left, right and
subwoofer. This may differ per setup.
LINK OUT:
These audio outputs receive the same signal as provided through the input. The
signal may then be linked to a second set or another amplier.
BLUETOOTH
®
(optional):
To be able to use the wireless Bluetooth
®
function, the PAS-300 must be paired
with the external Bluetooth® device that contains the music (mobile phone, tablet
or other). Pair the devices as follows:
1. Switch on the PAS-300 and enable the Bluetooth
®
function by pressing and
holding the “PAIR” button for at least 3 seconds until the status LED starts
ashing.
2. Enable the search function of the Bluetooth
®
device that contains the music;
refer to the user manual of that device.
3. Now select “ALECTO” in the list that appears in the display of the Bluetooth
®
that contains the music.
4. The status LED of the Bluetooth
®
function will now remain lit.
5. If asked for a password, please enter the PIN code “0000” on the Bluetooth
®
device (when the connection is interrupted, the status LED will start ashing
again).
6. Depending on the type of device that contains the music, you might have to set
this device to send its audio signal to the PAS-300 and not to the headphones
output or its own speaker; please refer to the user instructions of the external
device.
7. Attention: the PAS-300 only plays music; it does not support phone calls.
8. After use, please press and hold the “PAIR” button for at least 3 seconds to
switch off the Bluetooth
®
device. The status LED will now switch off.
ENVIRONMENT
• The packaging of this baby video monitor can be discarded as waste
paper. However, we advise you to save this packaging so you can
adequately protect the devices for transportation.
• In case the baby video monitor is being replaced, please return it to
your supplier; they will guarantee environment-friendly processing.
6
TECHNICAL SPECIFICATIONS
PAS-300:
Voltage: 230V~50Hz
Fuse: T 2,5A 230V
Woofer: 10”
Satellite: 4” Mediant x 2 and 1” Neodymium Tweeter
Impedance Satellite: 4Ω
System Freq. Resp.: 45Hz~20KHz +/-3dB
Subwoofer Freq. Resp.: 45Hz~140Hz +/-3dB
Satellite Freq. Resp.: 140Hz~20KHz +/-3dB
System Power: 380 Watts RMS
Subwoofer Power: 250 Watts RMS
Satellite Power: 2 x 65Watts RMS – impedanite minimal 4Ω
Satellite Dimensions(WxDxH): 150*160*410mm
Net Weight: 4.5Kg
Subwoofer Dimensions(WxDxH): 410*330*415mm
Net Weight: 15Kg
The amplier with Bluetooth
®
(optioneel)
With Overcurrent, Short Circuit, Overload and Overheat Protections
Warning: Using the speaker for long periods of time on high volumes
can lead to permanent ear damage. To protect your hearing, please
keep in mind the following:
• Increase the volume starting at the minimum up to a comfortable level.
• Do not listen for long periods of time on high volumes.
• Never increase the volume to outdo or ignore environmental noise.
• Decrease the volume when you cannot hear the people around you.
7
CONNECTION DETAILS
BALANCED/UNBALANCED
Stereo headphones:
Tip is left signal
Ring is right signal
Sleeve is mass,
earth or shielding
Tip
Ring
Sleeve
unbalanced mono:
Tip is signal
Sleeve is mass,
earth or shielding
Tip
Sleeve
balanced mono:
Tip is signal +
Ring is signal -
Sleeve is mass,
earth or shielding
Tip
Ring
Sleeve
Pull relief
Pull relief
Pull relief
PUSH
Balanced XLR connectior:
PIN 1 is mass,
earth or shielding
PIN 2 is signal +
PIN 3 is signal -
To 1 side, connect PIN 1 with PIN 3 for unbalanced XLR connection.
Balanced XLR cable:
PIN 1 is mass,
earth or shielding
PIN 2 is signal +
PIN 3 is signal -
To 1 side, connect PIN 1 with PIN 3 for unbalanced XLR cable.
2+
1+
1-
2-
2+
2
-
1-
1+
V1.0
Service
Help
Service Help
WWW.ALECTO.NL
NL 073 6411 355
(Lokaal tarief)
BE 03 238 5666
(Lokaal tarief)
(Tarif local)
DE 0180 503 0085
Lokale Festnetzkosten
Hesdo, Australiëlaan 1
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW.ALECTO.NL
NL 073 6411 355
BE 03 238 5666
DE 0180 503 0085
Hesdo, Australiëlaan 1, 5232 BB,
‘s-Hertogenbosch,
The Netherlands
(Lokaal tarief)
(Tarif local)
(Lokaal tarief)
(Lokale Festnetzkosten)
v2.1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Alecto PAS-300
Below you will find brief product information for Alecto PAS-300. It's an active sound set that consists of a subwoofer, two satellite speakers, and a set of speaker cables with Speakon plugs. The subwoofer has three separate speakers: one for the subwoofer and two (left and right) for the satellite speakers. The satellite speakers can be placed onto the supplied tripods. The subwoofer has volume controls for each speaker, which must be set before use. The ultimate volume is controlled on the external audio source.
Possible use cases:
- Home theater system
- PA system for small events
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Lenco BT-4650 Datasheet
-
Whirlwind SAT-1 Headphone Module User manual
-
Byron 00.640.85 Instructions Manual
-
Typhoon 50225 Datasheet
-
AudioCodes Mediant 1000 User manual
-
Audio Design Pro Trio Session User manual
-
HK Audio L.U.C.A.S 600 User manual
-
Audio Design Pro TRIO MASTER User manual
-
DAP Audio D3760 User manual
-
