Promax TVHUNTER+ ISDB-T Reference guide

Promax
Brand
Promax
Model
TVHUNTER+ ISDB-T
Type
Reference guide

Promax TVHUNTER+ ISDB-T is a versatile device that enables efficient detection, identification, and adjustment of ISDB-T/TB signals. It features a user-friendly interface with a clear display, making it easy to navigate through various functions.

With its detection capabilities, you can pinpoint the maximum power and align your antenna for optimal signal reception. The identification function allows you to view parameters of stored test points, tuned channel names, and identified services. You can also fine-tune signals using the adjustment feature to ensure compliance with regulations.

Promax TVHUNTER+ ISDB-T is a versatile device that enables efficient detection, identification, and adjustment of ISDB-T/TB signals. It features a user-friendly interface with a clear display, making it easy to navigate through various functions.

With its detection capabilities, you can pinpoint the maximum power and align your antenna for optimal signal reception. The identification function allows you to view parameters of stored test points, tuned channel names, and identified services. You can also fine-tune signals using the adjustment feature to ensure compliance with regulations.

Find the user’s manual on the download area at:
www.promaxelectronics.com
TVHUNTER +
PDF
USER MANUAL
DOWNLOAD
SCREEN ICONS REFERENCE
STATUS BAR
ISDB-T/T signal not locked.
USB
ISDB-T/T signal locked.
Power supply connected.
Battery power level.
Manual power off enabled.
Connected to PC through the USB port.
5/12/15/24/OFF
External voltage supplied through the RF connector (5V/12V/15V/24V/OFF)
SWITCHING ON/OFF
Switch on the TVHUNTER + pressing , or for four seconds.
If you press or for more than eight seconds when starting, it enables manual power off mode.
FRONT VIEW
QUICK START GUIDE
Input RF connector
1
2
3
Display
DETECTION/CONFIGURATION key
4
5
6
USB connector
Power input connector
IDENTIFICATION key
7
ADJUST key
TB
TB
TVHUNTER +
ISDB-T/T
B
ISDB-T/T
B
B
B
RF
1
2
3
4
6
7
5
USB
DETECTION
Plug the TVHUNTER + to the antenna socket and turn the antenna until the TVHUNTER + shows the maximum
power on the display. To avoid damage to other devices, when switching on the equipment, the external power supply
is always OFF by default. Select the external power through the setup menu and press to switch between 0V (OFF)
and the selected external supply voltage.
1)DET E CT OFF
MAX POWER RATE: 41%
POWER RATE: 40%
PRESS
DETECT
Maximum measured power
Current power
External power supply
1)DET E CT 5V
MAX POWER RATE: 41%
POWER RATE: 40%
PRESS DETECT TO
SWITCH THE EXTERNAL
SUPPLY VOLTAGE
(see CONFIGURATION)
RF
QUICK START GUIDE
6
NOTE: Once the antenna is aligned using the Detection mode, if it is unknown
the channels that can be received at the location, it is advisable
to "Auto-Scan" and save the results (see Configuration).
TVHUNTER +
ISDB-T/T
B
IDENTIFICATION
Press and wait until locking the signal. The display will show the parameters of the stored test point (selected name
and frequency), the name of multiplex channel tuned and its services identified at this test point. To change to another
test point or layer (A: one layer; A+B: two layers; A+B+C: three layers) press again.
QUICK START GUIDE
7
TVHUNTER +
ISDB-T/T
B
1)DE TECT 5V
MAX POWER RATE: 41%
POWE R RATE: 40%
2)IDENTIFY OFF
PROMAX CH01
C66 FR: 531.
NET:PROMAX TV
SERVICE LIST: 1
1)DE TECT 5V
MAX POWER RATE: 41%
POWE R RATE: 40%
PRESS
IDENTIFICATION
)
2 IDENTIFY OFF
PROMAX CH01
C66 FR: 531.
NET:PROMAX TV
SERVICE LIST: 1
Locked signal (black background)
Test Point Name
Tuned channel name
Identified services
TP 04 :
Sequential number of
the test point
TP 04 :
RF
RF
PRESS
SHORT PRESS: NEXT TEST POINT OR LAYER
LONG PRESS <1s: PREVIOUS TEST POINT OR LAYER
TB
TB
A
0MHz
B
0MHz
Short Key
Press
[2]
[2]
TP00 TP00:A TP00:B TP01
TB
TP00:C
TB
+
Long Key
Press
ADJUST
Press to perform fine-tuning. Check that every access point in the installation is meeting the criteria
established by current regulations. To measure another test point or layer (A: one layer; A+B: two layers; A+B+C: three layers)
press again until finding the test point you are looking for. Each layer has different parameters and therefore,
different measures.
CONFIGURATION
At the DETECTION screen, press and hold
until appears the configuration menu.
1)DET ECT 5V
MAX P OWER RA TE: 41%
POWER RA TE: 40%
)SETUP
OFF
1)CANCEL 2)OPTION 3)SELECT
START AUTO SCAN
EXTERNAL SUPPLY
SOUND CONTROL
BACKLIGHT MODE
CONTRAST LCD
CONFIRM & EXIT
OFF
ON
AUTO
It exits the configuration menu without saving changes
It scrolls along the menu options
It changes the parameter/Accepts
Start Auto Scan: It starts the auto-scan function.
External Supply: It allows selecting the external supply voltage for the antenna among 0V (OFF, by default), 5V, 12V,15V or 24V.
Confirm & Exit:
When using the TVHUNTER +, it may appear on the display some messages and icons, depending on the status or
event is taking place. These messages and icons are detailed below
Low power level battery. Plug it to the charger.
The external supply can be shortcut.
“SUPPLY OVER CURRENT”
“LOW BATTERY”
“VERY LOW BATTERY”
The equipment will be switched off immediately.
MESSAGE
DESCRIPTION
“SUPPLY SHORT CIRCUIT”
The external supply has a high current consumption.
“MANUAL POWER OFF”
The instrument has to be switched off by hand.
“AUTO POWER OFF”
The instrument will switch off after five minutes
of inactivity.
“BATTERY MODE”
When the battery is being charged.
“UPDATE MODE”
When the instrument is being updated.
MESSAGE
DESCRIPTION
“NETWORK NOT FOUND”
The instrument cannot find a TV network.
“SERVICES NOT FOUND”
“SIGNAL NOT DETECTED”
“FULL BATTERY”
“MPEG-2 NOT DETECTED”
“LOADING NETWORK”
“LOADING SERVICES”
“HIGH TEMPERATURE”
The instrument cannot detect the services of a network.
When no signal is detected.
Battery fully charged.
It is not detecting the Transport Stream MPEG-2 signal.
After finding a signal, needs a time to load the network.
After finding a network, needs a time to load services.
The operation temperature is too high.
The instrument must be switched off for a while.
If the problem persists, contact with the technical support.
Find the user’s manual on the download area at: www.promaxelectronics.com
Navegation Keys:
QUICK START GUIDE
(0 DG0103) 01/03/2013
TVHUNTER +
ISDB-T/T
B
1)DET EC T 5V
MAX POW ER RA TE : 41%
POWER R AT E: 4 0%
PRESS
ADJUST
Locked signal (black background)
Test Point Name
TV
FM
3)ADJ US T
OFF
C66 FR:531.
PO WER : 79.5d
B
uV
MER :
35
.0d
B
1.0E- 5CBER:
0
35
1.0E- 8VBER:
TP04:
LM:
Sequential number of
the test point
RF
PRESS
SHORT PRESS: NEXT TEST POINT OR LAYER
LONG PRESS <1s: PREVIOUS TEST POINT OR LAYER
TB
0MHz
>20.2dB
A
It applies and saves the changes made and exits the configuration menu.
v1.04.02
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Promax TVHUNTER+ ISDB-T Reference guide

Promax
Brand
Promax
Model
TVHUNTER+ ISDB-T
Type
Reference guide

Promax TVHUNTER+ ISDB-T is a versatile device that enables efficient detection, identification, and adjustment of ISDB-T/TB signals. It features a user-friendly interface with a clear display, making it easy to navigate through various functions.

With its detection capabilities, you can pinpoint the maximum power and align your antenna for optimal signal reception. The identification function allows you to view parameters of stored test points, tuned channel names, and identified services. You can also fine-tune signals using the adjustment feature to ensure compliance with regulations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents