Page is loading ...
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
TFT-LCD TV
OWNER S MANUAL'
MODELS:
HL26R-A
HL32R-A
R
2 TV LCD-TFT
Warning
RISK ELECTRIC SHOCK
DO NOT OPEN
CAUTION
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
!
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
Apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15)The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
16)The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the
apparatus normal use.
Class I apparatus shall be connected to a mains socket outlet with a protective earthing connection.
Owner s Manual 3
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to
try to correct the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may be not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite cores must be
used when connecting this LCD display to video equipment; and maintain at least 40cm spacing to other
peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
FCC STATEMENT
Safety Instructions
4 TV LCD-TFT
Safety Instructions
SAVE THESE INSTRUCTIONS
Thank you for purchasing the product. This easy-to-use manual will guide you in getting the best use of your
product. Remember to record the model and serial number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
Introduction
Contents
Owner s Manual 5
6
7
8
9
9
9
9
10
11
11
12
12
13
14
15
15
16
16
17
17
17
17
18
18
18
18
18
18
Front Panel Controls..................................................
Back Panel Controls...................................................
Universal Remote Control..........................................
Connection Instructions.............................................
............................................................
External equipment Connections..............................
Antenna Connection.............................................
...................................................
External AV Source Setup.....................................
...................................................
...................................................
.............................................
VGA Connection...................................................
HDMI In .........................................................
......................................
......................................................
......................................................
.....................................................
Operation.................................................................
Switching On/Off the TV set.....................................
....................................
.........................................
......................................
......................................
........................................
Mute......................................................................
...............................................
............................................
Accessories
VCR connection
DVD connection
DTV connection
Digital Audio Output
tput
Connecting Headphones
Cable sample
Removing the table stand and installing a wall
mount bracket
Choose the Menu Language
Choose the Input source
SAP Broadcasts Setup
Power source
Basic Operating Instructions
Select the desired program
Select the desired sound
To add or delete your favorite channels to the
favorite channels list
Menu Operations......................................................
Set up Menu Options..............................................
................................
Automatic Scan....................................................
Adding Channels..................................................
Adding or removing a channel................................
Adding a Channel Label.........................................
Video Menu Options................................................
How to select picture mode....................................
How to customize your own picture status...............
Audio Menu Options................................................
How to select audio mode......................................
How to customize your own audio status.................
Feature Menu Options.............................................
Time Setting..........................................................
Sleep Timer setting................................................
Advanced Video Settings.......................................
..............
....................
Setting Parental Controls........................................
Password Set........................................................
Closed Caption style..............................................
CCD.....................................................................
............................................................
Product Specification................................................
Troubleshooting.......................................................
To select the TV signal source
Screen Setup for Component or VGA mode
Parental Control rating and categories
Maintenance
19
19
19
19
19
20
20
20
20
21
21
21
21
22
22
22
23
23
24
25
26
26
27
28
29
30
Introduction
6 TV LCD-TFT
Front panel controls
This is a simplified representation of front panel.
Here shown may be somewhat different from your TV.
1.MENU: Menu display.
2.INPUT: Press to show the input source mode. In the MENU/INPUT screen,
these buttons serve as OK buttons.
3.VOL -/+: Press to adjust the volume .In the MENU screen, these buttons
serve as left/right buttons.
4.CH -/+ : Press to scan through channels. To scan quickly through channels,
press and hold down either +/- . In the MENU screen, these buttons
serve as up/down buttons.
5.POWER: Press to turn on and off the TV.
6.HDMI In2: Connect a signal to
7. Headphone jack : Headphone audio output terminal.
8.S-VIDEO In: Connect S-Video out from an S-VIDEO device to the S-VIDEO input.
9.AV2 VIDEO In: Connects the video signal from a video device.
10.AV2 AUDIO In: connect to hear stereo sound from an external device.
11. Remote Sensor Receivers Irsignals from the remote control. Do not put
anything near the sensor ,as its function may be affected.
HDMI.
L - AUDIO - R
L - AUDIO - R
HDMI2 IN
HDMI2 IN
S-VIDEO2 IN
S-VIDEO2 IN
VIDEO2 IN
VIDEO2 IN
VIDEO
MENU INPUT VOL+ VOL- CH+ CH- POWER
Controls
2
1
1 1
Y
Pb
Pr
L
R
L
R
VIDEO
S-VIDEO
S-VIDEO
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
OUT
L
R
DVI AUDIO
AUDIO
L
R
AUDIO
COMPONENT IN
COMPONENT IN
VIDEO IN
VIDEO IN
1
AUDIO OUT
AUDIO OUT
VGA IN
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
Introduction
Owner s Manual 7
Connection Options
1. Digital Audio Output: Connect digital audio from various types of equipment.
NOTE: In standby mode, these ports will not work.
2. DVI Audio In: Connect a component video device to these jacks.
3.
HDMI In: Connect a signal to .
5.
6.
7. VIDEO In:
8. DVD/DTV In(Component ): Connect a component video device to these jacks.
9. AUDIO In: Connect to hear stereo sound from an external device.
10. In:
COMPONENT AUDIO In: Connect to hear stereo sound from an external device.
12. AUDIO In: Connect to hear stereo sound from an external device.
13. AUDIO Out: Connect to the left and right audio input jacks of your audio or video equipment.
Antenna Input: Connect cable or antenna signals to the TV, either directly or through your cable box.
4.
VGA Audio In: Connect the audio L/R cables from a computer to this jack.
VGA Video In: Connect a video cable from a computer to this jack.
Connects the video signal from a video device.
S-VIDEO Connect S-Video out from an S-VIDEO device to the S-VIDEO input.
11.
HDMI
Back panel controls
Introduction
8 TV LCD-TFT
The remote control cannot be operated unless the batteries are properly loaded.
When using the remote control, aim it at the remote control sensor on the TV.
Universal Remote Control
Function introduction
1.POWER
Press to turn on and off the TV.
2.CH.LIST
Press to open the channel list.
3.ZOOM
Press to select the aspect ratio.
4.SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog
mode. Change the audio language in DTV mode.
5.Numeric buttons
Press to change the channel.
6.MENU
Brings up the main menu to the screen.
7.THUMBSTICK (Up/Down/Left/Right/OK)
Allows you to navigate the on-screen menus and adjust
the system settings to your preference.
8.EXIT
Clears all on-screen displays and returns to TV viewing
from any menu.
9.PICTURE
Select the picture mode appropriate for the program's
character.
10.VOL+/-
Press to adjust the volume.
11. AUDIO
Select the audio mode appropriate for the program's
character.
12.Shortcut Button of Input
TODAY: Press to enter TODAY signal;
NEXT DAY: Press to enter NEXT DAY signal;
PAGE-: Press to enter PAGE- signal;
PAGE+: Press to enter PAGE+ signal.
13.GUIDE
Shows program schedule.
14.TV
Press to switch TV mode.
15.COMPONENT
Press to enter COMPONENT signal.
16.VGA
Press to enter VGA signal.
17.ADD/ERASE
Add or erase favorite program.
18.FAV.LIST
Open the favorite channel list.
19.MUTE
Switches the sound on or off.
20.SLEEP
Displays the Sleep Timer option.
21.RECALL
Switch the current channel to the last channel you have
viewed.
22. button
Press to select additional channels (digital )being
broadcast by the same station. For example, to select
channel“54 3”, press “54”, then press “ ” and “3”.
23.INPUT
Show the input source mode.
24.DISPLAY
When you watch the TV, press the key, the information
displays on top of the screen.
25.CCD
Select the closed caption.
26.CH+/-
Press to scan through channels. To scan quickly through
channels, press and hold down either +/- .
27.FREEZE
Freezes the currently-viewed picture, but audio continues.
Press FREEZE button again to resume the normal picture.
28.S-VIDEO
Press to enter S-VIDEO signal.
29.VIDEO
Press to enter VIDEO signal.
30.HDMI
Press to enter HDMI signal.
POWER FAV.LIST
ADD/ERASE
ZOOM
MENU
SAP
SLEEP
MUTE
1234
5678
90
RECALL
INPUT
OK
EXIT DISPLAY
PICTURE
VOL+
CH+
AUDIO VOL- CH- FREEZE
TODAY
GUIDE TV VIDEO S-VIDEO
COMPONENT
VGA
NEXTDAY
PAGE- PAGE+
HDMI
CCD
CH.LIST
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
TFT-LCD TV
OWNERS MANUAL'
MODELS:
HL26R-A
HL32R-A
R
ANT IN
ANT IN
ANT IN
ANT IN
Installation
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an
outdoor antenna .
.
Over-the-air TV reception quality will depend on your antenna type, antenna
location and antenna positioning
External Equipment Connections
Antenna Connection
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
VHF Antenna
UHF Antenna
Turn clockwise to tighten
RF Coaxial Wire (75 ohm)
Bronze Wire
Be careful not to bend the bronze wire
when connecting the antenna.
Bronze Wire
To improve the picture quality in a poor signal area,
please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV`s, install
a 2-Way Signal Splitter in the connections.
To install the antenna properly please contact a
professional in your area.
Accessories
Remote control
Owner`s manual
Alkaline battery(AAA) 2
Power cable
Connection Instructions
Owner s Manual 9
POWER FAV.LIST
ADD/ERASE
ZOOM
MENU
SAP
SLEEP
MUTE
1234
5678
90
RECALL
INPUT
OK
EXIT DISPLAY
PICTURE
VOL+
CH+
AUDIO VOL- CH- FREEZE
TODAY
GUIDE TV VIDEO S-VIDEO
COMPONENT
VGA
NEXTDAY
PAGE- PAGE+
HDMI
CCD
CH.LIST
2
1
1 1
Y
Pb
Pr
L
R
L
R
VIDEO
VIDEO
S-VIDEO
S-VIDEO
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
OUT
L
R
DVI AUDIO
DVI AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
COMPONENT IN
COMPONENT IN
VIDEO IN
VIDEO IN
1
AUDIO OUT
AUDIO OUT
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
VCR connection
NOTE: All cables shown are not included with the TV.
There are several ways to connect your television, depending on the components you want to connect
and the quality of the signal you want to achieve. The following are examples of some different ways
to connect your TV with different input sources.
Choose Your Connection
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
Connection Option 1
Set VCR output switch to channel 3 or 4 and
then tune the TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
shown in the figure.
When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
If you connect an S-VIDEO output from VCR to
the S-VIDEO input, the picture quality is
improved; compared to connecting a regular
VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s
manual.)
3. Select the input source with using the
INPUT button on the remote control, and
then press / button to select the source,
press OK button to confirm.
Installation
Connection Instructions
10 TV LCD-TFT
2
1
1 1
Y
Pb
Pr
Pr
L
R
L
R
VIDEO
VIDEO
S-VIDEO
S-VIDEO
VGA
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
OUT
OUT
L
R
DVI AUDIO
DVI AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
COMPONENT IN
COMPONENT IN
VIDEO IN
VIDEO IN
1
AUDIO OUT
AUDIO OUT
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
Installation
How to connect
1. Connect the DVD video outputs (COMPONENT) to
the Y Pb Pr jacks on the TV and connect the DVD audio
outputs to the Y Pb Pr Audio IN jacks on the TV, as
shown in the figure.
2. If your DVD only has an S-VIDEO output jack,
connect this to the S-VIDEO input on the TV. as shown
in the figure.
Note
If your DVD player does not have component video
output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select
Y Pb Pr mode.
3. Press Play button on external equipment for program
play.
4. Refer to the DVD player's manual for operating
instructions.
How to connect
Connect the audio and video cables from the external
equipment's output jacks to the TV input jacks, as shown
in the figure. When connecting the TV to external equipment,
match the jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
How to use
1. Select the input source with using the INPUT button on
the remote control.
2. Press / button to select the desired source.
3. Press OK button to confirm.
4. Operate the corresponding external equipment.
Video Game Set
Camcorder
Component Input ports
To get better picture quality, connect a DVD player to the
component input ports as shown below.
Component ports
on the TV
Video output ports
on DVD player
Y Pb Pr
Y Pb Pr
Y B-Y R-Y
Y Cb Cr
Y P P
BR
External A/V Source Setup
DVD connection
DVD
or
Connection Instructions
Owner s Manual 11
2
1
1 1
Y
Pb
Pr
Pr
L
R
L
R
VIDEO
VIDEO
S-VIDEO
S-VIDEO
VGA
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
OUT
OUT
L
R
DVI AUDIO
DVI AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
COMPONENT IN
COMPONENT IN
VIDEO IN
VIDEO IN
1
AUDIO OUT
AUDIO OUT
VGA IN
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
!
2
1
1 1
Y
Pb
Pb
Pr
L
R
L
R
VIDEO
VIDEO
S-VIDEO
S-VIDEO
VGA
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
OUT
OUT
L
R
DVI AUDIO
DVI AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
COMPONENT IN
VIDEO IN
VIDEO IN
1
AUDIO OUT
AUDIO OUT
VGA IN
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
2
1
1 1
Y
Pb
Pb
Pr
L
R
L
R
VIDEO
VIDEO
S-VIDEO
S-VIDEO
VGA
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
OUT
OUT
L
R
DVI AUDIO
DVI AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
COMPONENT IN
COMPONENT IN
VIDEO IN
1
AUDIO OUT
VGA IN
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
Installation
Digital Set-top Box
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do
receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480i,480p,720p,
1080i).
How to connect
Use the TV`s COMPONENT , VGA or HDMI
jack for video connections, depending on
your set-top box connector. Then, make
the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the
owner`s manual for the digital set-top box.)
2. Use INPUT on the remote control to select
COMPONENT , VGA or HDMIsource.
Send the TV`s audio to external audio equipment (stereo
system) the Digital Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Digital
Audio(Optical) Output port.
2. Connect the other end of the optical cable to the digital
audio (optical)input on the audio equipment.
See the external audio equipment instruction manual for
operation.
When connecting with external audio equipments, such
as amplifers or speakers, please turn the TV speakers off.
via
Note
Digital Audio Output
Caution: Do not look into the optical output port.
Looking at the laser beam may damage your
vision.
DTV connection
Signal
480i
480p
720p
1080i
COMPONENT
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI
Connection Instructions
12 TV LCD-TFT
2
1
1 1
Y
Pb
Pb
Pr
Pr
L
R
L
R
VIDEO
VIDEO
S-VIDEO
VGA
VGA
VGA AUDIO
VGA AUDIO
AUDIO
AUDIO
L
R
AUDIO
OUT
L
R
DVI AUDIO
DVI AUDIO
AUDIO
AUDIO
L
R
AUDIO
AUDIO
COMPONENT IN
COMPONENT IN
VIDEO IN
VIDEO IN
1
AUDIO OUT
AUDIO OUT
VGA IN
VGA IN
HDMI IN
HDMI IN
ANT IN
ANT IN
OPTICAL OUT
OPTICAL OUT
Installation
How to connect
1. To get the best picture quality, adjust the PC graphics card to 1024
2. Use the TV`s VGA or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your VGA
connector.
If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either
VGA r HDMI/DVI IN to display the PC on the TV.
If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe VGA
DVI; (the other mode is set to Plug and Play automatically by the TV.)
3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.
How to use
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Use INPUT on the remote control to select PC or HDMI/DVI source.
4.Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC
graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
Note
1.Use a DVI cable.
2.Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently
imprinted on the screen.
3. The synchronization input form for Horizontal and Vertical frequencies is separate.
x768 .
IN o
ror
HDMI/
Resolution
Frame
frequency
(Hz)
VGA
SVGA
XGA
60Hz
800x600
1024x768
60Hz
60Hz
Mode
Resolution
75Hz
75Hz
VGA connection
Connection Instructions
640x480
1280x1024
1280x768
1920x1080
Owner s Manual 13
When the source device(DVD player or Set Top Box) supports HDMI
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).
2. No separated audio connection is necessary.
How To Use
If the source device supports Auto HDMI function, the output resolution of the source device will be automatically
set to 1280x720p.
If the source device does not support Auto HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Select HDMI input source in input source option of Select Main source menu.
When the source device(DVD player or Set Top Box) supports DVI
How To Connect
1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).
2. A separated audio connection is necessary.
3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio
In port located on the left side of HDMI port.
How To Use
If the source device supports Auto DVI function, the output resolution of the source device will be automatically set
to 1280x720p.
If the source device does not support Auto DVI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Press the INPUT button to select HDMI input source in input source option of Select Main source menu.
Installation
HDMI Input
Connection Instructions
14 TV LCD-TFT
Installation
Power source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for
operation on AC. Insert the AC cord plug into
a standard polarized AC outlet.
Note
Never connect the AC line cord plug to other
than the specified voltage. Use the attached
power cord only.
If the polarized AC cord does not fit into a non-
polarized AC outlet, do not attempt to file or cut
the blade. It is the user`s responsibility to have
an electrician replace the obsolete outlet.
If you cause a static discharge when touching
the unit and the unit fails to function, simply
unplug the unit from the AC outlet and plug it back
in. The unit should return to normal operation.
Polarized AC Cord Plug
AC Outlet
Wider Hole
and Blade
You can connect a set of headphones to your set if you wish to watch a
TV programme without disturbing the other people in the room.
Connecting Headphones
Note
Prolonged use of headphones at a high volume
may damage your hearing.
You will not receive sound from the speakers
when you connect headphones to the system.
Plug a set of headphones into the 3.5mm
mini-jack socket on the side panel of the set.
L-AUDIO-R
L-AUDIO-R
HDMI2 IN
HDMI2 IN
S-VIDEO2 IN
S-VIDEO2 IN
VIDEO2 IN
VIDEO2 IN
VIDEO
VIDEO
Connection Instructions
Owner s Manual 15
Installation
Removing the table stand and installing a
wall mount bracket
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable
(Stereo to RCA type)
(not supplied with the product)
Cable sample
Connection Instructions
16 TV LCD-TFT
Use 4X M6 screws to secure the wall
bracket (not supplied) to the back of your TV.
Remove 4X M4 screws securing the
stand to the TV, then remove the stand.
Operation
Source List
TV
Composite 1
Composite 2
S-Video1
S-Video2
Component1
Component2
VGA
HDMI/DVI1
HDMI/DVI12
Switching On/Off the TV set
Choose the Input source
Air
English
Tuning Band
Signal Level
Auto Channel Search
Add On Channel Search
Manual Channel Set
Channel Labels
Menu Language
Reset
Picture
Audio
Setup
Feature
To Move OK To Select Exit To Exit
To Move OK To Select Exit To Exit
Operation
Owner s Manual 17
In the manual, the OSD (on screen display) may be
different from your TV`s, because it is just an example to
help you with the TV operation.
There are several options you might need to set up in
order for your TV to work properly. Read the instructions
that follow.
1. First, connect power cord correctly.
2. Press POWER button to turn on your TV.
3. Select the viewing source by using INPUT button.
4. When finished using the TV, press POWER button
again. The TV reverts to standby mode.
5. If you intend to be away on vacation, disconnect the
power plug from the wall power outlet.
Note
If the TV in power on , the screen show information
according the type of input signal , the information will
disappear. If there is no signal , "No Signal" will display
on the screen.
If there is no signal , NO SIGNAL will display on the
screen.
Choose the Menu Language
When you start using your set for the first time, you must
select the language which will be used for displaying
menus and indications.
1.Choose the TV Input and then pressMENU button.
2.Press / to select Setup menu.
3.Press , then press / to select
the .
4.Press or OK , then press / to
select language.
You can select English Spanish or French
button
button button
button button
Menu Language
Change the picture source so you can watch your TV,
cable TV, VCR, DVD, or any
other devices that are connected to your TV.
1. Press INPUT button to enter the select main picture
source menu and then press / button to select the
desired items
.
2. Press OK button to confirm .
TV, Composite 1, Composite 2, S-
Video1, S-Video2, Component1, Component2,VGA,
HDMI/DVI1, HDMI/DVI2
Basic Operating Instructions
18 TV LCD-TFT
Select the desired program
1.Using CH+/- buttons
Press CH+ button on the remote control to select a
channel number increasing direction.
Press CH- button on the remote control to select a
channel number decreasing direction.
2.You can use the number buttons and button on the
remote control to directly select TV channels and
press OK to confirm.
Note
If skip is On on one channel, press CH+/- button, the
channel will not appear.
Select the desired sound
1.Press VOL+ button to increase the volume. A number
will appear on screen indicating the volume level.
2.Press VOL- button to decrease the volume. A number
will appear on screen indicating the volume level.
When the volume button are pressed the volume level is
Displayed automatically on the TV screen.
Mute
When you need to pay attention o a conversation, or
there is a telephone calling you or there are some
guests visiting you, the sound elimination(mute)
Function is very convenient.
1.Press MUTE button to mute the sound temporarily. A
mute icon appears on the screen. At this time, the
sound of the TV set is turned off.
2.Press MUTE or VOL+ button again to restore the
sound.
/
To add or delete your favorite
channels to the favorite channels
list
1.Press CH+/- buttons to select a channel.
2. Press ADD/ERASE button to add the channel to your
favorite channels list.
3.Press ADD/ERASE button again to delete the channel.
To tune to a favorite channel:
1.Press FAV.LIST to open your favorite channels list.
2.Press button to select a channel on the list.
3.Press OK button. Your TV tunes to that channel.
SAP Broadcasts Setup
This TV can receive MTS stereo programs and SAP
(Secondary Audio Program) that accompanies the
stereo program; if the station transmits an additional
sound signal as well as the original one.
When having selected SAP button on the remote
control, this TV can only receive the signal when the
TV station transmits the proper signals.
Mono sound is automatically received if the
broadcast is only in Mono; even though Stereo or
SAP has been selected.
Select Mono if you want to listen to mono sound
during stereo/SAP broadcasting.
Stereo or SAP can be received in a Analog channel.
To listen to SAP
1. P SAP to select your desired mode in a analog
signal. Each time you press SAP, Mono,
Stereo or SAP appear. If other languages are
available on the digital signal, select them with the
SAP button.
2. Press EXIT to save and return to TV viewing.
ress
Operation
Operation
Auto Channel Search- Air
Add On Channel Search
Scanning
0
0
Scanning
0
0
Performing First Pass
Analog Found
Digital Found
Progress(%)
Performing First Pass
Analog Found
Digital Found
Progress(%)
12
12
Exit To Exit
Exit To Exit
Menu Operations
Owner s Manual 19
Air
Air
English
English
Tuning Band
Signal Level
Auto Channel Search
Add On Channel Search
Manual Channel Set
Channel Labels
Menu Language
Reset
Tuning Band
Signal Level
Auto Channel Search
Add On Channel Search
Manual Channel Set
Channel Labels
Menu Language
Reset
Picture
Audio
Setup
Feature
To Move OK To Select Exit To Exit
Picture
Audio
Setup
Feature
To Move OK To Select Exit To Exit
Setup Menu Options
To select the TV signal source
1. Press MENU button, then press / button to select
Setup menu.
2. Press button, then press / button one or more
times to select the T
uning Band .
3. Press or OK button to select the TV signal source.
Automatic Scan
Automatically finds all channels available through
antenna or cable inputs, and stores them in memory on
the all channel list.
Note
The channel menu will be only operated in normal TV
mode.
1. Press MENU button, then press / button to select
Setup menu.
2. Press button, then press / button one or more
times to select the Auto Search .
3. Press or OK button to start scanning.
4 .To cancel searching, press EXIT button.
Your TV searches for channels that have a signal. Any
channel that has no signal or a poor signal are not saved.
During the search, the following appears.
Your LCD TV scans for analog channels, then scans
again for digital channels.
When the search is complete the first channel appears
on the screen.
Adding Channels
You can add channels that were not found in a previous
scan for channels.
For example, if your LCD TV found channels 1 through
20 and you select the Add On Search option,
your LCD TV scans for channels starting at 21.
1. Press MENU button, then press / button to select
Setup menu.
2. Press button, then press / button one or more
times to select the Add On Search.
3. Press or OK button to start scanning.
4. To cancel searching, press the EXIT button.
Channel
Channel
Channel
Operation
Manual Channel Set Menu
Channel Labels Menu
Ch 9-1 ATSC dmo Viewable
Ch 10-0 Viewable
Ch 11-0 Viewable
Menu Operations
Setup Menu Options
20 TV LCD-TFT
Air
Air
English
English
Tuning Band
Signal Level
Auto Channel Search
Add On Channel Search
Manual Channel Set
Channel Labels
Menu Language
Reset
Tuning Band
Signal Level
Auto Channel Search
Add On Channel Search
Manual Channel Set
Channel Labels
Menu Language
Reset
Picture
Audio
Setup
Feature
To Move OK To Select Exit To Exit
To Move To Change OK To Select
To Move To Change Exit To Exit
Picture
Audio
Setup
Feature
To Move OK To Select Exit To Exit
Adding or removing a channel
You can add or remove a channel from the channel list. If you
remove a channel from the list, your LCD TV skips the
channel when you press the CH buttons. You can still tune to
the channel by pressing the number buttons.
1. Press MENU button, then press / button to select
Setup menu.
2. Press button, then press / button to select the
Manual Channel Set.
3. Press or OK button, the menu opens.
4. Press / button to select the channel, then press
button to toggle between viewable and not viewable.
Adding a Channel Label
1. Press MENU button ,then press / button to select
Setup menu.
2. Press button, then press / button to select the
Channel Labels.
3. Press or button, t
4. Press / button to move the cursor to the channel
filed or label filed, then press / button to select a
channel while the cursor is in the channel filed, or
press / button to select the character while the
cursor is in the label filed.
OK he menu opens.
Video Menu Options
The TV menu gives you an overview of the menus you
can select.
Note
Depending on the input signal, one or more menu items
may not be selectable.
How to select picture mode
The picture mode provides the pre-defined images
settings: Standard/Vivid/Bright/User.
1. Press MENU button ,then press / button to select
Picture menu.
2. Press button, then press / button to select the
Picture Mode.
3. Press / button to select the option.
You can also press PICTURE button on the remote
Control to select the option.
Wide
Standard
50
50
50
50
50
Picture Mode
Contrast
Brightness
Sharpness
Color
Tint
Aspect Ratio
Picture
Audio
Setup
Feature
To Move OK To Select Exit To Exit
/
