Tekonsha 118375† Installation guide

Tekonsha
Brand
Tekonsha
Model
118375†
Type
Installation guide

This manual is also suitable for

Tekonsha 118375† is a 7.5 amp per circuit trailer wiring harness that allows you to connect your vehicle's electrical system to a trailer. It is designed to be easy to install, with no cutting or splicing of wires required. The harness simply plugs into your vehicle's taillight connectors, and then you can connect your trailer's lights to the harness. The harness is also compatible with a variety of trailers, including those with electric brakes.

Here are some of the features and benefits of the Tekonsha 118375†:

  • Easy to install - no cutting or splicing of wires required
  • Plugs into your vehicle's taillight connectors

Tekonsha 118375† is a 7.5 amp per circuit trailer wiring harness that allows you to connect your vehicle's electrical system to a trailer. It is designed to be easy to install, with no cutting or splicing of wires required. The harness simply plugs into your vehicle's taillight connectors, and then you can connect your trailer's lights to the harness. The harness is also compatible with a variety of trailers, including those with electric brakes.

Here are some of the features and benefits of the Tekonsha 118375†:

  • Easy to install - no cutting or splicing of wires required
  • Plugs into your vehicle's taillight connectors
Installation instructions
Instructions d'installation
Instrucciones de instalación
18375-037 1/12/01
Fig. 6
FRANÇAIS
ENGLISH ESPAÑOL
1. Remueva las dos tuercas plásticas que
sostienen las alfombras que recubren las
luces traseras dentro del baúl (1 en el lado del
conductor, 1 en el lado del pasajero).
2. Hale el forro del lado del conductor lo
suficiente como para permitir el acceso al
conector del cableado que se encuentra
montado en la pared trasera del baúl. Separe
los conectores, tenga cuidado de no romper
las orejetas de seguridad.
3. Inserte el conector de 3 vías de la conexión
en T entre los conectores del cableado del
vehículo. Asegúrese de que las orejetas de
seguridad cumplan su función de mantener la
conexión unida fijamente.
4. Encamine el terminal de la conexión en T que
tiene un solo cable por debajo del forro a el
lado del pasajero. Localice el conector que se
encuentra en el mismo lugar como en el lado
del conductor. Separe los conectores y haga
la unión con el conector en T.
5. Pruebe la instalación con una luz de prueba o
un remolque.
6. Coloque nuevamente las dos alfombras que
cubren las luces traseras y enrosque las dos
tuercas plásticas.
Esta unidad es clasificada para 7.5 amperios
por el circuito.
1. Retirez les deux écrous plastiques qui
attachent la doublure de feutre du coffre
derrière les feux arrière (1 du côté
conducteur, 1 du côté passager).
2. Retirez la doublure du côté conducteur assez
pour permettre de l ’accès au connecteur
monté à l ’arrière du coffre. Séparez les
connecteurs; faites attention de ne pas briser
les languettes de retenue.
3. Insérez le connecteur àtrois fils du
connecteur en T entre les connecteurs du
véhicule, vous assurant que toutes les
languettes de retenue sont serrées.
4. Acheminez l ’embout à un fil du connecteur
en T en dessous de la doublure jusqu ’au
côté passager. Localisez le connecteur au
lieu correspondant à celui du côté
conducteur. Séparez les connecteurs et
branchez le connecteur en T.
5. Utilisez une lampe témoin ou une remorque
pour vérifier que l ’installation est correcte.
6. Remettez la doublure du coffre et rattachez
les deux écrous plastiques.
Cette inité est évaluéé pour 7.5 ampères par
circuit.
1.
Remove 2 plastic nuts that hold the felt trunk
liner behind the taillights (1 on the driver’s
side, 1 on the passenger side.)
2. Pull the liner on the driver’s side out far
enough to allow access to the connector
mounted to the rear wall of trunk. Separate
the connectors, being careful not to break the
locking tabs.
3. Insert the T-Connector’s 3 wire connector
between the vehicle’s connectors, making
sure all tabs are locked into place.
4. Route the single wire end of the T-Connector
under the liner to the passenger side. Locate
the passenger side connector in the same
spot as on the driver’s side. Separate the
connectors and make the attachment.
5. Test the installation with a test light or trailer.
6. Reposition the trunk liner and reattach the 2
plastic nuts
This unit is rated for 7.5 amps per circuit.
  • Page 1 1

Tekonsha 118375† Installation guide

Tekonsha
Brand
Tekonsha
Model
118375†
Type
Installation guide
This manual is also suitable for

Tekonsha 118375† is a 7.5 amp per circuit trailer wiring harness that allows you to connect your vehicle's electrical system to a trailer. It is designed to be easy to install, with no cutting or splicing of wires required. The harness simply plugs into your vehicle's taillight connectors, and then you can connect your trailer's lights to the harness. The harness is also compatible with a variety of trailers, including those with electric brakes.

Here are some of the features and benefits of the Tekonsha 118375†:

  • Easy to install - no cutting or splicing of wires required
  • Plugs into your vehicle's taillight connectors
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents