Tekonsha 118331 Installation guide

118331
Tekonsha
Brand
Tekonsha
Model
118331
Type
Installation guide

This manual is also suitable for

Tekonsha 118331 is a T-connector adapter that allows you to connect a trailer harness connector to your vehicle's existing wiring system. It features a 4-ampere per circuit rating, making it suitable for a wide range of towing applications. Installation is simple: remove the protective cap from the vehicle's connector, connect the adapter, and test the connection with a test light or trailer.

Tekonsha 118331 is a T-connector adapter that allows you to connect a trailer harness connector to your vehicle's existing wiring system. It features a 4-ampere per circuit rating, making it suitable for a wide range of towing applications. Installation is simple: remove the protective cap from the vehicle's connector, connect the adapter, and test the connection with a test light or trailer.

ENGLISH
1. Locate tow vehicle’s trailer harness
connector.This harness is located
under the vehicle, behind the rear
bumper, on the passenger side of
the vehicle.
2. Remove protective cap B (and save)
from connector A, being careful not
to break the locking tabs. Check to
see that the mating surfaces of the
connectors are free of dirt and clean
if necessary.
3. Connect the T-connector adapter
end C to the vehicle’s connector A.
Be sure that the T-connector is fully
inserted with locking tabs in place.
4. Test the installation with a test
light or trailer.
This unit is rated for 4 amps per cir-
cuit.
ESPAÑOL
1. Localice el conector del cableado
que el vehículo posee para la conex-
ión de remolque. Este cableado se
encuentra debajo del vehículo, detrás
de la defensa trasera, en el lado del
pasajero.
2. Remueva la tapa de protección B
(guárdela) del conector A, tenga
cuidado de no romper las orejetas
de seguridad. Asegúrese de que las
superficies a unirse estén libres de
polvo, límpielas si es necesario.
3. Conecte la punta C del conector en
T al conector A del vehículo. Asegúrese
de que las orejetas de seguridad
cumplan su función de mantener la
conexión unida firmemente.
4. Pruebe la instalación con una luz
de prueba o un remolque.
Esta unidad es clasificada para 4
amperios por el circuito.
FRANÇAIS
1. Localisez au véhicule le con-
necteur du faisceau de fils pour con-
necter une remorque. Ce faisceau se
trouve en dessous du véhicule, der-
rière le pare-chocs arrière, du côté
passager.
2. Enlevez le capuchon protecteur B
(gardez-le) du connecteur A; faites
attention de ne pas briser les
languettes de retenue. Vérifiez que
les surfaces homologues des
connecteurs ne sont pas sales;
nettoyez-les si nécessaire.
3. Connectez l’embout C de l’adaptateur
du connecteur en T au connecteur A
du véhicule. Assurez-vous que les
connecteurs soient insérés à fond et
que les languettes de retenue soient
en place.
4. Utilisez une lampe témoin ou une
remorque pour vérifier que
l'installation est correcte.
Cette inité est évaluéé pour 4
ampères par circuit.
Installation instructions
Instructions d’installation
Instrucciones de instalación
18331-037 1/16/01
A
B
C
View Under Right Rear Side
Vu dessous du côté droit arrière
Vista debajo del lado derecho trasero
  • Page 1 1

Tekonsha 118331 Installation guide

118331
Tekonsha
Brand
Tekonsha
Model
118331
Type
Installation guide
This manual is also suitable for

Tekonsha 118331 is a T-connector adapter that allows you to connect a trailer harness connector to your vehicle's existing wiring system. It features a 4-ampere per circuit rating, making it suitable for a wide range of towing applications. Installation is simple: remove the protective cap from the vehicle's connector, connect the adapter, and test the connection with a test light or trailer.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers