Page is loading ...
1
EN
QUICK REFERENCE GUIDE
ÉPIX Strip IP QRG Rev. 3
About This Guide
The ÉPIX Strip IP Quick Reference Guide (QRG) has basic product information such as connection and mounting.
Download the ÉPIX Drive 2000 IP User Manual from www.chauvetprofessional.com
for more details.
Disclaimer
The information and specifications contained in this QRG are subject to change without notice.
LIMITED WARRANTY
FOR WARRANTY REGISTRATION AND COMPLETE TERMS AND CONDITIONS PLEASE VISIT OUR WEBSITE.
For Customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration
.
For Customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and
Germany: www.chauvetlighting.eu/warranty-registration
.
Chauvet warrants that this product shall be free from defects in material and workmanship under normal use, for the
period specified in, and subject to the exclusions and limitations set forth in the full limited warranty on our website. This
warranty extends only to the original purchaser of the product and is not transferable. To exercise rights under this
warranty, you must provide proof of purchase in the form of an original sales receipt from an authorized dealer that shows
the product name and date of purchase. THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. This
warranty gives you specific legal rights. You may also have other rights that vary from state to state and country to
country. This warranty is valid only in the United States, United Kingdom, Republic of Ireland, Belgium, the Netherlands,
Luxembourg, France, Germany and Mexico. For warranty terms in other countries, please consult your local distributor.
Safety Notes
These Safety Notes include important information about installation, use, and maintenance.
• DO NOT open this product. It contains no user-serviceable parts.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the
product from power via breaker or by unplugging it.
• CAUTION: This product’s housing may be hot when lights are operating.
• CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid
ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow
product to fully acclimate to the surrounding environment before connecting it to power.
• CAUTION: This product’s housing may be hot when lights are operating.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
• DO NOT leave any flammable material within 50 cm of this product while operating or connected to power.
• USE a safety cable when mounting this product overhead.
• DO NOT submerge this product (IP65). Temporary outdoor operation is fine.
• When using this product in an outdoor environment, use IP65 (or higher) rated power and data cables. Be sure to
secure unused power and data ports with attached IP65 covers.
• DO NOT operate this product if the housing, ports, or cables appear damaged.
• DO NOT connect this product to a dimmer or rheostat.
• ONLY connect this product to an ÉPIX Drive 2000 IP or an ÉPIX Drive 900.
• Only use the hanging/mounting bracket to carry this product.
• In the event of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.
Contact
Outside the U.S., United Kingdom, Ireland, Benelux, France, Germany, or Mexico, contact your distributor to request
support or return a product. Refer to Contact Us
at the end of this QRG for contact information.
What is Included
• ÉPIX Strip IP
• Square Milky Filter (Installed)
• Black Stealth Filter
• Round Milky Filter
• Quick Reference Guide
EN
2
ÉPIX Strip IP QRG Rev. 3
QUICK REFERENCE GUIDE
Product Overview
Product Dimensions
Power
This product is powered by an ÉPIX Drive 2000 IP. Refer to the ÉPIX Drive 2000 IP User Manual for detailed instructions
on how to connect this product to power.
Power Linking
You can link up to 10 ÉPIX Strip IP products to each port of an ÉPIX Drive 2000 IP. Never exceed this number.
Scrambled Pulse-Width Modulation
This product features Scrambled-PWM (S-PWM) technology, which de-synchronizes the pulse widths of each color of the
multi-color LEDs. This ensures that there is always some LED output, reducing flicker, and maintaining the same
grayscale performance.
• Use ONLY IP65 4-pin XLR cables with the ÉPIX Strip IP. For our CHAUVET Professional line of
IP65 4-pin XLR cables, go to https://www.chauvetprofessional.com/accessories
.
• To eliminate wear and improve its lifespan, during periods of non-use completely disconnect
the ÉPIX Drive 2000 IP from power via breaker or by unplugging it.
Data/Power In
Bracket Position Adjustment Knobs
(used to align end to end on truss)
Interlocking
Hardware
Mounting Bracket
Fastening Knob/
Safety Loop
Data/Power Out
Filter
39.37 in
1000 mm
7.04 in
178.9 mm
3.15 in
80 mm
1.33 in
34 mm
1.42 in
36 mm
3.46 in
88 mm
3.27 in
83 mm
2.05 in
52 mm
5.04 in
128 mm
3
EN
QUICK REFERENCE GUIDE
ÉPIX Strip IP QRG Rev. 3
Filter Installation
The ÉPIX Strip IP includes a Square Milky Filter already installed. Follow the procedure below to install the included Black
Stealth Filter or Round Milky Filter.
1. Locate the end cap of the product that does not have the interlocking hardware.
2. Push in on the end-cap latch.
3. Slide the installed filter out and replace it with the desired filter.
4. Release the end-cap latch.
Mounting
Before mounting this product, read the Safety Notes. Use at least one mounting point per product. Make sure the
mounting clamps are capable of supporting the weight of the product. For our CHAUVET Professional line of mounting
clamps, go to http://trusst.com/products
.
Mounting Diagram
Interlocking Hardware
End-Cap Latch
Safety Cable
Safety Loop
Eye Bolts
Mounting Clamp
EN
4
ÉPIX Strip IP QRG Rev. 3
QUICK REFERENCE GUIDE
Vertical Mounting Instructions
1. Attach the clamp to the mounting bracket.
2. Attach the clamp to the desired structure or surface.
3. Attach a safety cable to the product’s safety loop.
Never attach more than 4 products together when hanging vertically from a single mounting
point.
Attach the Safety Cable
of the first product to
the mounting point
Attach the Safety Cable of the
following products to the
Bracket of the preceding product
5
EN
QUICK REFERENCE GUIDE
ÉPIX Strip IP QRG Rev. 3
Series Attachment Instructions
The ÉPIX Strip IP can be attached in an end to end formation to create a strip up to 4 meters long from one mounting
point. Do not connect any more than 4 ÉPIX Strip IP products in a row when hanging vertically.
1. Loosen the 2 fastening eye bolts.
2. Slide the connecting bracket out until it stops and tighten the eye bolt closest to the center of the product.
3. Slide the second ÉPIX Strip IP into the connecting bracket and tighten the remaining eye bolt.
4. Attach the safety cable as shown in Vertical Mounting Instructions
.
Install the safety cable last when attaching ÉPIX Strip IP products in series.
1
2
3
EN
6
ÉPIX Strip IP QRG Rev. 3
QUICK REFERENCE GUIDE
Technical Specifications
Dimensions and Weight
Note: Dimensions in inches are rounded.
Power
Light Source
Photometrics
Control
Thermal
Ordering
Filter Length Width Height Weight
Square Milky Filter 39.37 in (1000 mm) 3.93 in (100 mm) 1.33 in (34 mm) 6 lb (2.7 kg)
Black Stealth Filter 39.37 in (1000 mm) 3.46 in (88 mm) 1.33 in (34 mm) 6 lb (2.7 kg)
Round Milky Filter 39.37 in (1000 mm) 5.03 in (128 mm) 1.77 in (45 mm) 6 lb (2.7 kg)
Power Supply Range Power Linking
ÉPIX Drive 2000 IP 100 to 240 VAC, 50/60 Hz 10 per ÉPIX Drive 2000 IP port
Parameter 120 V, 60 Hz 208 V, 60 Hz 230 V, 50 Hz
Consumption 35 W 44 W 44 W
Operation Current 0.292 A 0.210 A 0.195 A
Power I/O U.S./Worldwide UK/Europe
Power Input Connector IP65 4-pin XLR IP65 4-pin XLR
Power Cord Plug IP65 4-pin XLR IP65 4-pin XLR
Type Color Quantity Lifespan
SMD 505 LED Tri-color RGB 100 50,000 hours
Parameter Square Milky Filter Black Stealth Filter Round Milky Filter
Viewing Angle 160° 140° 160°
Illuminance 2,470 NITS 1,455 NITS 1,360 NITS
Pixel Pitch 10 mm 10 mm 10 mm
Refresh Rate 4,800 Hz 4,800 Hz 4,800 Hz
Data I/O Channel Range (Art-Net™/sACN) Channel Range (Kling-Net)
IP65 4-pin XLR 15, 17, 30, 60, 150 or 300
Determined by ArKaos MediaMaster
software
Maximum External Temp. Cooling
113 °F (45 °C) Convection
Product Name Item Name Item Code UPC Number
ÉPIX Strip IP EPIXSTRIPIP 03091318 781462216665
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Multi-Language
QUICK REFERENCE GUIDE
27
ÉPIX Strip IP QRG Rev. 3
Contact Us
Visit the applicable website above to verify our contact information and instructions to request support. Outside the
U.S., United Kingdom, Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record.
General Information Technical Support
Chauvet World Headquarters
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetprofessional.com
Chauvet Europe Ltd.
Address: Unit 1C Email: [email protected]
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetprofessional.eu
NG16 6NT
Voice: +44 (0) 1773 511115
Fax: +44 (0) 1773 511110
Chauvet Europe BVBA
Address: Stokstraat 18 Email: BNLtec[email protected]
9770 Kruishoutem
Belgium Website: www.chauvetprofessional.eu
Voice: +32 9 388 93 97
Chauvet France
Address: 3, Rue Ampère
91380 Chilly-Mazarin
Email: [email protected]
France Website: www.chauvetprofessional.eu
Voice: +33 1 78 85 33 59
Chauvet Germany
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Email: DEtech@chauvetlighting.de
Germany Website: www.chauvetprofessional.eu
Voice: +49 421 62 60 20
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
(Entrance by Calle 2)
Email: [email protected]
Zona Industrial Lerma Website: www.chauvetprofessional.mx
Lerma, Edo. de México, CP 52000
Voice: +52 (728) 690-2010
/
