Chauvet ÉPIX Reference guide

Page is loading ...

1

EN

QUICK REFERENCE GUIDE

ÉPIX Strip Tour 50 QRG Rev. 2

About This Guide

The ÉPIX Strip Tour 50 Quick Reference Guide (QRG) has basic product information such as connection and mounting.

Download the ÉPIX Drive 900 or ÉPIX Drive 2000 IP. User Manual from www.chauvetprofessional.com

for more details.

Disclaimer

The information and specifications contained in this QRG are subject to change without notice.

Safety Notes

These Safety Notes include important information about installation, use, and maintenance.

• DO NOT open this product. It contains no user-serviceable parts.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the

product from power via breaker or by unplugging it.

• DO NOT look at the light source when the product is on.

• CAUTION: This product’s housing may be hot when lights are operating.

• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.

• DO NOT leave any flammable material within 50 cm of this product while operating or connected to power.

• CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to warm humid

ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow

product to fully acclimate to the surrounding environment before connecting it to power.

• USE a safety cable when mounting this product overhead.

• DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect

it. (IP20)

• DO NOT operate this product if the housing, or I/O ports appear damaged. Have the damaged parts replaced by

a Chauvet certified technician at once.

• DO NOT connect this product to a dimmer or rheostat.

• ONLY connect this product to an ÉPIX Drive 900 or ÉPIX Drive 2000 IP.

• ONLY use the hanging/mounting bracket to carry this product.

• In the event of a serious operating problem, stop using immediately.

• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact your distributor to request support or return a

product. Visit www.chauvetprofessional.com

for contact information.

What is Included

• ÉPIX Strip Tour 50

• Black stealth filter (Installed)

• White Frost Filter

• Warranty Card

• Quick Reference Guide

EN

2

ÉPIX Strip Tour 50 QRG Rev. 2

QUICK REFERENCE GUIDE

Product Overview

Data/Power In

Bracket Position Adjustment Knobs

Interlocking

Hardware

Mounting Bracket

Fastening Knob/

Safety Loop

Data/Power Out

Filter

3

EN

QUICK REFERENCE GUIDE

ÉPIX Strip Tour 50 QRG Rev. 2

Product Dimensions

Power

This product is powered by an ÉPIX Drive 900 or ÉPIX Drive 2000 IP. Refer to the ÉPIX Drive 900/ÉPIX Drive 2000 IP

User Manual for detailed instructions on how to connect this product to power.

Power Linking

You can link up to 10 ÉPIX Strip Tour 50 products to each port of an ÉPIX Drive 900/ÉPIX Drive 2000 IP. Never exceed

this number.

• To eliminate wear and improve its lifespan, during periods of non-use completely disconnect

the ÉPIX Drive 900 or ÉPIX Drive 2000 IP from power via breaker or by unplugging it.

19.68 in

500 mm

1.20 in

30.5 mm

1.34 in

34 mm

1.26 in

32 mm

2.74 in

69.5 mm

EN

4

ÉPIX Strip Tour 50 QRG Rev. 2

QUICK REFERENCE GUIDE

Filter Installation

The ÉPIX Strip Tour 50 includes a black stealth filter already installed. Follow the procedure below to install the included

Black Stealth Filter or Round Milky Filter.

1. Locate the end cap of the product that does not have the interlocking hardware.

2. Push in on the end-cap latch.

3. Slide the installed filter out and replace it with the desired filter.

4. Release the end-cap latch.

Mounting

Before mounting this product, read the Safety Notes. Use at least one mounting point per product. Make sure the

mounting clamps are capable of supporting the weight of the product. For our CHAUVET Professional line of mounting

clamps, go to http://trusst.com/products

.

Mounting Diagram

End-Cap Latch

Safety Cable

Safety Loop

Eye Bolts

Mounting Clamp

5

EN

QUICK REFERENCE GUIDE

ÉPIX Strip Tour 50 QRG Rev. 2

Vertical Mounting Instructions

1. Attach the clamp to the mounting bracket.

2. Attach the clamp to the desired structure or surface.

3. Attach a safety cable to the product’s safety loop.

Never attach more than 6 products together when hanging vertically from a single mounting

point.

Attach the Safety Cable

of the first product to

the mounting point

Attach the Safety Cable of the

following products to the

Bracket of the preceding product

EN

6

ÉPIX Strip Tour 50 QRG Rev. 2

QUICK REFERENCE GUIDE

Series Attachment Instructions

The ÉPIX Strip Tour 50 can be attached in an end to end formation to create a strip up to 3 meters long from one

mounting point. Do not connect any more than 6 ÉPIX Strip Tour 50 products in a row when hanging vertically.

1. Loosen the 2 fastening eye bolts.

2. Slide the connecting bracket out until it stops and tighten the eye bolt closest to the center of the product.

3. Slide the second ÉPIX Strip Tour 50 into the connecting bracket and tighten the remaining eye bolt.

4. Attach the safety cable as shown in Vertical Mounting Instructions

.

Install the safety cable last when attaching ÉPIX Strip Tour 50 products in series.

1

2

3

7

EN

QUICK REFERENCE GUIDE

ÉPIX Strip Tour 50 QRG Rev. 2

Technical Specifications

Dimensions and Weight

Note: Dimensions in inches are rounded.

Power

Power Linking

Light Source

Photometrics

Control

Thermal

Ordering

Length Width Height Weight

19.68 in (500 mm) 1.2 in (30.5 mm) 4.7 in (119.5 mm) 2 lb (1 kg)

Power Supply Range

ÉPIX Drive 900 or ÉPIX Drive 2000 IP 100 to 240 VAC, 50/60 Hz

Parameter 120 V, 60 Hz 208 V, 60 Hz 230 V, 50 Hz

Consumption 7 W 9 W 8 W

Operation Current 0.051 A 0.046 A 0.031 A

Power I/O U.S./Worldwide UK/Europe

Power Input Connector 4-pin XLR 4-pin XLR

Power Cord Plug 4-pin XLR 4-pin XLR

Power Linking

36

Type Color Quantity Lifespan

SMD 5050 LED Tri-color RGB 50 50,000 hours

Parameter Dome Filter Black Stealth Filter White Frost Filter

Viewing Angle 180° 125° 125°

Illuminance 700 NITS 270 NITS 1,100NITS

Pixel Pitch 20 mm 20 mm 20 mm

Refresh Rate 4,700 Hz 4,700 Hz 4,700 Hz

Data I/O Channel Range (Art-Net™/sACN) Channel Range (Kling-Net)

4-pin XLR 75

Determined by ArKaos MediaMaster

software

Maximum External Temp. Cooling

113 °F (45 °C) Convection

Product Name Item Name Item Code UPC Number

ÉPIX Strip Tour 50 EPIXSTRIPTOUR50 09031436 781462217846

Page is loading ...

NL

26

ÉPIX Strip Tour 50 BH Rev. 2

BEKNOPTE HANDLEIDING

Technische Specificaties

Afmetingen en gewicht

Let op: Afmetingen in inches zijn afgerond.

Power

Lichtbron

Photometrics

Control

Thermisch

Bestellen

Lengte Breedte Lengte Gewicht

19,68 in (500 mm) 1,20 in (30,5 mm) 4,70 in (119,5 mm) 2 lb (1 kg)

Stroomvoeding Bereik

ÉPIX Drive 900/ÉPIX Drive 2000 IP 100 tot 240 VAC, 50/60 Hz

Parameter 120 V, 60 Hz 208 V, 60 Hz 230 V, 50 Hz

Verbruik 7 W 9 W 8 W

In gebruik 0,051 A 0,046 A 0,031 A

Stroom I/O VS/Wereldwijd VK/Europa

Aansluitingspoort 4-pins XLR 4-pins XLR

Snoerstekker 4-pins XLR 4-pins XLR

Type Kleur Aantal Levensduur

SMD 5050 LED Driekleurige RGB 50 50.000 uur

Parameter Domefilter Stealthfilter Frostfilter

Kijkhoek 180° 125° 125°

Verlichtingssterkte 700 NITS 270 NITS 1.100 NITS

Pixelpitch 20 mm 20 mm 20 mm

Verversingssnelheid 4.700 Hz 4.700 Hz 4.700 Hz

Gegevens I/O Kanaalbereik (Art-Net™/sACN) Kanaalbereik (Kling-Net)

4-pins XLR 75

Bepaald door ArKaos MediaMaster

software

Maximum Externe Temperatuur Koelsysteem

113 °F (45 °C) Convectie

Productbeschrijving Productnaam Artikelcode UPC Nummer

ÉPIX Strip Tour 50 EPIXSTRIPTOUR50 00031436 781462217846

Multi-Language

QUICK REFERENCE GUIDE

27

ÉPIX Strip Tour 50 QRG Rev. 2

Contact Us

Outside the U.S., United Kingdom, Ireland, Mexico or Benelux, contact the dealer of record. Follow the instructions to

request support or to return a product. Visit our website for contact details.

World Headquarters

General Information Technical Support

Address: 5200 NW 108th Ave. Voice: (844) 393-7575

Sunrise, FL 33351 Fax: (954) 756-8015

Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com

Fax: (954) 929-5560

Website

Toll Free: (800) 762-1084 www.chauvetlighting.com

EUROPE

General Information Technical Support

Address: Stokstraat 18 Email: eutech@chauvetlighting.eu

9770 Kruishoutem

Website

Belgium www.chauvetlighting.eu

Voice: +32 9 388 93 97

General Information Technical Support

Address: Unit 1C Email: [email protected]

Brookhill Road Industrial Estate

Pinxton, Nottingham, UK

Website

NG16 6NT www.chauvetlighting.co.uk

Voice: +44 (0) 1773 511115

Fax: +44 (0) 1773 511110

MEXICO

General Information Technical Support

Address: Av. de las Partidas 34 - 3B

(Entrance by Calle 2)

Email: [email protected]

Zona Industrial Lerma

Website

Lerma, Edo. de México, CP 52000 www.chauvet.com.mx

Voice: +52 (728) 690-2010

Chauvet ÉPIX Reference guide

Chauvet ÉPIX Reference guide

in other languages

Related papers

Other documents