Chicago Electric Item 63583 Quick start guide

Chicago Electric
Brand
Chicago Electric
Model
Item 63583
Type
Quick start guide

This manual is also suitable for

Chicago Electric Item 63583 is a 90 AMP FLUX WIRE WELDER that can weld 18 Ga. – 3/16″ Steel Plate. It can weld mild, low alloy steel materials (not for aluminum or stainless steel). The wire feed speed and MAX/MIN settings are adjustable according to the chart. The device provides the ability to correct common welding issues, such as current being too high or too low, wire feed being too fast or too slow, and weld speed being too fast or too slow. The flux-core welds will have a coat of slag over them until cleaned.

Chicago Electric Item 63583 is a 90 AMP FLUX WIRE WELDER that can weld 18 Ga. – 3/16″ Steel Plate. It can weld mild, low alloy steel materials (not for aluminum or stainless steel). The wire feed speed and MAX/MIN settings are adjustable according to the chart. The device provides the ability to correct common welding issues, such as current being too high or too low, wire feed being too fast or too slow, and weld speed being too fast or too slow. The flux-core welds will have a coat of slag over them until cleaned.

WARNING
To prevent serious injury, read manual warnings and instructions before use.
BASIC WELDING INSTRUCTIONS AND WELDING TIPS ARE IN MANUAL.
ON MIN
OFF MAX
WIRE FEED SPEED
GUN
GROUND
120V~
60Hz
20A
90 AMP FLUX WIRE WELDER
ITEM 68887
Specications
Wire 0.030″- 0.035″ Flux-Core
Capacity 18 Ga. – 3/16″ Steel Plate
Weldable
Materials
Mild, Low Alloy Steel
(Not for Aluminum or Stainless Steel)
I
O
WARNING
To prevent re and
serious injury:
Keep torch and
wire clear of
grounded objects
while welder
plugged in.
2"
Contact
Tip
Nozzle
HOLD
GUN
CLEAR
2"-3"
wood
block
Assemble face shield handle and cover handle.
Install FLUX-CORE
wire spool.
Insert wire through
both wire liners and
clamp it into feed
mechanism.
See manual if
changing wire size.
63583 QUICK START GUIDE
Take off nozzle and tip,
plug in welder, turn it on,
and squeeze trigger until
wire comes out.
Incrementally tighten
wire feed tension
knob clockwise until
wire will bend from
feed tension at 2"-3".
Unplug welder and
replace nozzle and tip.
Adjust wire feed speed
and MAX/MIN settings
according to chart.
Hold gun clear of workpiece,
then plug in welder and turn it on.
welding
wire
Wire
Spool
17e
.030″
clockwise
ON MIN
OFF MAX
WIRE FEED SPEED
GUN
GROUND
120V~
60Hz
20A
90 AMP FLUX WIRE WELDER
ITEM 68887
Specications
Wire 0.030″- 0.035″ Flux-Core
Capacity 18 Ga. – 3/16″ Steel Plate
Weldable
Materials
Mild, Low Alloy Steel
(Not for Aluminum or Stainless Steel)
I
O
Wire Spool
Spring
Top Plate
Knob
Spindle
Good
Weld
ON MIN
OFF
MAX
WIRE FEED SPEED
GUN
GROUND
120V~
60Hz
20A
90 AMP FLUX WIRE WELDER
ITEM 68887
Specications
Wire 0.030″-
0.035″ Flux-Core
Capacity 18 Ga. –
3/16″ Steel Plate
Weldable
Materials
Mild, Low Alloy Steel
(Not for Aluminum or Stainless Steel)
I
O
Current
Too Low
TO CORRECT:
ON MIN
OFF MAX
WIRE FEED SPEED
GUN
GROUND
120V~
60Hz
20A
90 AMP FLUX WIRE WELDER
ITEM 68887
Specications
Wire 0.030″- 0.035″ Flux-Core
Capacity 18 Ga. – 3/16″ Steel Plate
Weldable
Materials
Mild, Low Alloy Steel
(Not for Aluminum or Stainless Steel)
I
O
or
ON MIN
OFF
MAX
WIRE FEED SPEED
GUN
GROUND
120V~
60Hz
20A
90 AMP FLUX WIRE WELDER
ITEM 68887
Specications
Wire 0
.030″- 0.035″ Flux-Core
Capacity 18 Ga. – 3/16″ Steel Plate
Weldable
Materials
Mild, Low Alloy Steel
(Not for Aluminum or Stainless Steel)
I
O
Current
Too High or
Wire Feed
Too Fast
TO CORRECT:
Weld
Speed
Too Fast
TO CORRECT:
weld
slower
Weld
Speed
Too Slow
TO CORRECT:
weld
faster
maintain
less
than
1
/
2
"
stickout
Stickout
Too Long
TO CORRECT:
CLEAN WELDS FIRST!
Flux-core welds will have a coat of slag over them until cleaned.
63583 WELD EXAMPLE PICTURES
  • Page 1 1
  • Page 2 2

Chicago Electric Item 63583 Quick start guide

Chicago Electric
Brand
Chicago Electric
Model
Item 63583
Type
Quick start guide
This manual is also suitable for

Chicago Electric Item 63583 is a 90 AMP FLUX WIRE WELDER that can weld 18 Ga. – 3/16″ Steel Plate. It can weld mild, low alloy steel materials (not for aluminum or stainless steel). The wire feed speed and MAX/MIN settings are adjustable according to the chart. The device provides the ability to correct common welding issues, such as current being too high or too low, wire feed being too fast or too slow, and weld speed being too fast or too slow. The flux-core welds will have a coat of slag over them until cleaned.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents